移植与电子模块通信相关代码

source/elec_det/hardware/adc_cfg.h

@@ -0,0 +1,97 @@
+#ifndef ADC_CFG_H_
+#define ADC_CFG_H_
+#include "base/define.h"
+
+
+
+
+
+
+#define AN_UA_CH					ADC_Channel_12	//AD2
+#define AN_MAL_CH					ADC_Channel_13 //AD2
+#define RAD_01_CH					ADC_Channel_2   //AD2
+#define AN_CAP_AD_CH      ADC_Channel_15  //AD2
+
+
+
+#define VCC_2V5_CH				ADC_Channel_1 //AD1
+#define VCC_1V25_CH				ADC_Channel_3 //AD1
+#define V_LA_M_CH					ADC_Channel_6 //AD1 
+#define V_LA_H_CH					ADC_Channel_7 //AD1
+#define AD_OUTA_CH				ADC_Channel_10 //AD1
+#define AD_OUTB_CH				ADC_Channel_11 //AD1
+
+
+#define ADC_CURR_DE   ADC2
+
+
+
+#define AD_SCAN_COUNT 16
+#define AD_SCAN_SAMPLE 8
+
+#define FIREBUS_ADC_BUF_LEN 160
+extern volatile uint16_t FireBus_ADC_Buf[FIREBUS_ADC_BUF_LEN];
+
+#define ADC_SPEED_SLOW			ADC_SampleTime_239Cycles5
+#define ADC_SPEED_MIDLE			ADC_SampleTime_71Cycles5
+#define ADC_SPEED_HIGH			ADC_SampleTime_13Cycles5  
+#define ADC_SPEED_HFAST			ADC_SampleTime_7Cycles5 
+void AdcDef_Init(void);
+void StartADC2Channel(uint32_t  channel, uint32_t speed);
+#define ADC_CurChnnelSet(channel,speed) StartADC2Channel(channel,speed)
+//桥丝电阻测量通道
+#define ADC_ResistorChannelSet(speed)  StartADC2Channel(RAD_01_CH,speed);
+//电容电压测量
+#define ADC_CAPVolChannelSet(speed)    StartADC2Channel(AN_CAP_AD_CH,speed);
+
+void StartADC1Channel(uint32_t  channel);
+void StartADC2ChannelV2(uint32_t  channel);
+uint32_t GetADC2_Fast(void);
+//电流采集通道
+#define ADC_GetCurADCFast()  GetADC2_Fast()
+//桥丝电阻采集通道
+#define ADC_GetResistorADCFast() GetADC2_Fast()
+//电容电压采集通道
+#define ADC_GetCAPVolADCFast()  GetADC2_Fast()
+
+uint32_t GetADC1_Fast(void);
+
+uint32_t GetADC2_Value(uint32_t channel);
+#define ADC_GetCurADC(chnnel) GetADC2_Value(channel)
+
+void GetADC1_Value(uint32_t channel,uint16_t* buf,uint16_t len);
+float Get_Temperature(void);
+/*
+@brief 稳定获取总线电流
+@rtv 返回电流值 0.1uA
+*/
+uint16_t ADC_Comm1p6mA_EndCur(void);
+/*
+@brief 稳定获取总线电流
+*/
+uint16_t ADC_GetBaseStableCur(void);
+/*
+@brief 电流降到指定电流下的时间
+@param 采样超时
+@param end_adv 检测启动和结束判线
+@param 最大电流ad
+@param 电流下降过程中最大向上波动
+@rtv 时间采集值0.1ms
+*/
+uint16_t AD_GetChgEnergy(uint16_t sample_timeout, uint16_t end_adv,uint16_t* max_cul,uint16_t *shake_adv);
+/*
+@brief 电流降到指定电流下的时间
+@param  执行时间 单位0.1ms
+@rtv 最大波动AD值
+*/
+uint16_t AD_CurMonitor(uint32_t us_times);
+/*
+使用该函数，对ADC触发一次采样，到用该函数前，应调用一次StartADC0Channel(ch)
+*/
+uint16_t GetADC_Fast(ADC_TypeDef* adc_periph);
+
+/*获取桥丝电阻*/
+void AD_SampleResistor(uint16_t* channels_re);
+/*测量电容电压*/
+uint16_t AD_SampleCap(uint16_t delay);
+#endif