kunlun/mfgtool/oem_tool/hw3/oem_tool_hw.c

#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <errno.h>
#include <string.h>
#include <stddef.h>
#include <arpa/inet.h>

#include "../../../inc/hw/reg/riscv3/2/gpio_mtx_sig.h"

#include "oem_common.h"
#include "oem_tool_hw.h"

#define RC_TOTAL_GPIO           128
#define RC_TOTAL_UART           IOT_UART_MAX_NUM_V1
#define RC_TOTAL_PWM            IOT_PWM_MAX_NUM_V1
#define RC_TOTAL_ADC            IOT_ADC_MAX_NUM_V1
#define RC_TOTAL_LEDC           IOT_LEDC_MAX_NUM_V1
#define RC_TOTAL_SPI            IOT_SPI_MAX_NUM_V1
#define RC_TOTAL_I2C            IOT_I2C_MAX_NUM_V1
#define RC_TOTAL_SPINLOCK       IOT_SPINLOCK_MAX_NUM_V1
#define RC_TOTAL_DMA            IOT_DMA_MAX_NUM_V1
#define RC_TOTAL_GPTIMER        IOT_GPTIMER_MAX_NUM_V1
#define RC_TOTAL_MAILBOX        IOT_MAILBOX_MAX_NUM_V1
#define RC_TOTAL_WDG            IOT_WDG_MAX_NUM_V1
#define RC_TOTAL_ZC             3   //3 phase
#define RC_TOTAL_PA             3   //3 phase

#define OEM_TOOL_DEBUG_EB       0
#if OEM_TOOL_DEBUG_EB
#define oem_debug_print(fmt, ...) printf(fmt, ##__VA_ARGS__)
#else
#define oem_debug_print(fmt, ...)
#endif

typedef enum _category_type_t {
    CATEGORY_GENERAL = 0,
    CATEGORY_RC_HDR,
    /* external reosurce */
    CATEGORY_GPIO,
    CATEGORY_UART,
    CATEGORY_PWM,
    CATEGORY_ADC,
    CATEGORY_LEDC,
    CATEGORY_SPI,
    CATEGORY_I2C,
    /* internal resource */
    CATEGORY_SPINLOCK,
    CATEGORY_DMA,
    CATEGORY_GPTIMER,
    CATEGORY_MAILBOX,
    CATEGORY_WDG,
    /* special resources, only one zc\pa\rf module,
     * only binding signal are required, resource allocation is not required.
     */
    CATEGORY_ZC,
    CATEGORY_PA,
    CATEGORY_MAX = 0xff,
} category_type_t;

typedef enum _peripheral_signal_type_t {
    SIGNAL_UART_TX = 0,
    SIGNAL_UART_RX,
    SIGNAL_UART_RTS,
    SIGNAL_UART_CTS,
    SIGNAL_SPI_CS,
    SIGNAL_SPI_CLK,
    SIGNAL_SPI_MISO,
    SIGNAL_SPI_MOSI,
    SIGNAL_I2C_SDA,
    SIGNAL_I2C_SCL,
    /* PWM complementary output */
    SIGNAL_PWM_A_OUT,
    SIGNAL_PWM_B_OUT,
    SIGNAL_LEDC_OUT,
    SIGNAL_ZC_UP,
    SIGNAL_ZC_DOWN,
    SIGNAL_PA_TX_EN,
    SIGNAL_PA_RX_EN,
    SIGNAL_PA_GAIN,
    SIGNAL_MAX = 0xff,
} peripheral_signal_type_t;

typedef struct _current_rc_info_t {
        uint8_t device_last;
        uint8_t core_last;
        uint8_t pin_idx;
        iot_board_info_v1_t *rc_ptr;
} current_rc_info_t;

typedef struct _diff_data_buffer_t {
    uint8_t buf[4096];
    uint16_t len_total;
} diff_data_buffer_t;

typedef struct _oem_tool_info_t {
    uint32_t line_num;  /* source file(*.ini file) line number */
    uint8_t rc_cnt;
    iot_board_info_v1_t *rc_list[128];
    current_rc_info_t rc;
    diff_data_buffer_t buf;
} oem_tool_info_t;

oem_tool_info_t oem_tool = {0};

/* The order is the same as category_type_t */
char *g_category_string[] = {
    "general",
    "rc_header",
    "gpio",
    "uart",
    "pwm",
    "adc",
    "ledc",
    "spi",
    "i2c",
    "spinlock",
    "dma",
    "gptimer",
    "mailbox",
    "wdg",
    "zc",
    "pa",
};

/* The order is the same as peripheral_signal_type_t */
char *g_signal_string[] = {
    "uart_tx",
    "uart_rx",
    "uart_rts",
    "uart_cts",
    "spi_cs",
    "spi_clk",
    "spi_miso",
    "spi_mosi",
    "i2c_sda",
    "i2c_scl",
    "pwma",
    "pwmb",
    "ledc_out",
    "zc_up",
    "zc_down",
    "pa_tx_en",
    "pa_rx_en",
    "pa_gain",
};

uint8_t gpio_func_sel(uint8_t gpio)
{
    return 0;
}

// 输出inid
// sig_type gpio信号的类型 number，外设或内设的编号
uint8_t get_matrix_signal_inid(uint8_t sig_type, uint8_t number)
{
    uint8_t inid = 0xff;

    switch (sig_type) {
    case SIGNAL_UART_RX:
        switch (number) {
        case 0:
            inid = GPIO_MTX_UART0_RXD_IN;
            break;
        case 1:
            inid = GPIO_MTX_UART1_RXD_IN;
            break;
        case 2:
            inid = GPIO_MTX_UART2_RXD_IN;
            break;
        case 3:
            inid = GPIO_MTX_UART3_RXD_IN;
            break;
        case 4:
            inid = GPIO_MTX_UART4_RXD_IN;
            break;
        case 5:
            inid = GPIO_MTX_UART5_RXD_IN;
            break;
        case 6:
            inid = GPIO_MTX_UART6_RXD_IN;
            break;
        case 7:
            inid = GPIO_MTX_UART7_RXD_IN;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_UART_CTS:
        switch (number) {
        case 0:
            inid = GPIO_MTX_UART0_CTS_IN;
            break;
        case 1:
            inid = GPIO_MTX_UART1_CTS_IN;
            break;
        case 2:
            inid = GPIO_MTX_UART2_CTS_IN;
            break;
        case 3:
            inid = GPIO_MTX_UART3_CTS_IN;
            break;
        case 4:
            inid = GPIO_MTX_UART4_CTS_IN;
            break;
        case 5:
            inid = GPIO_MTX_UART5_CTS_IN;
            break;
        case 6:
            inid = GPIO_MTX_UART6_CTS_IN;
            break;
        case 7:
            inid = GPIO_MTX_UART7_CTS_IN;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_SPI_MISO:
        switch (number) {
        case 0:
            inid = GPIO_MTX_SPI_M0_SI_IN;
            break;
        case 1:
            inid = GPIO_MTX_SPI_M1_SI_IN;
            break;
        case 2:
            inid = GPIO_MTX_SPI_M2_SI_IN;
            break;
        case 3:
            inid = GPIO_MTX_SPI_M3_SI_IN;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_I2C_SDA:
        switch (number) {
        case 0:
            inid = GPIO_MTX_I2C0_SDA_IN;
            break;
        case 1:
            inid = GPIO_MTX_I2C1_SDA_IN;
            break;
        case 2:
            inid = GPIO_MTX_I2C2_SDA_IN;
            break;
        case 3:
            inid = GPIO_MTX_I2C3_SDA_IN;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_ZC_UP:
        switch (number) {
        case 0:
            inid = GPIO_MTX_MAC_ZC_UP_PHASE_0;
            break;
        case 1:
            inid = GPIO_MTX_MAC_ZC_UP_PHASE_1;
            break;
        case 2:
            inid = GPIO_MTX_MAC_ZC_UP_PHASE_2;
            break;
        }
        break;
    case SIGNAL_ZC_DOWN:
        switch (number) {
        case 0:
            inid = GPIO_MTX_MAC_ZC_DOWN_PHASE_0;
            break;
        case 1:
            inid = GPIO_MTX_MAC_ZC_DOWN_PHASE_1;
            break;
        case 2:
            inid = GPIO_MTX_MAC_ZC_DOWN_PHASE_2;
            break;
        }
        break;
    default:
        break;
    }

    return inid;
}

// 输出outid
// sig_type gpio信号的类型 number，外设或内设的编号
uint8_t get_matrix_signal_outid(uint8_t sig_type, uint8_t number)
{
    uint8_t outid = 0xff;

    switch (sig_type) {
    case SIGNAL_UART_TX:
        switch (number) {
        case 0:
            outid = GPIO_MTX_UART0_TXD_OUT;
            break;
        case 1:
            outid = GPIO_MTX_UART1_TXD_OUT;
            break;
        case 2:
            outid = GPIO_MTX_UART2_TXD_OUT;
            break;
        case 3:
            outid = GPIO_MTX_UART3_TXD_OUT;
            break;
        case 4:
            outid = GPIO_MTX_UART4_TXD_OUT;
            break;
        case 5:
            outid = GPIO_MTX_UART5_TXD_OUT;
            break;
        case 6:
            outid = GPIO_MTX_UART6_TXD_OUT;
            break;
        case 7:
            outid = GPIO_MTX_UART7_TXD_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_UART_RTS:
        switch (number) {
        case 0:
            outid = GPIO_MTX_UART0_RTS_OUT;
            break;
        case 1:
            outid = GPIO_MTX_UART1_RTS_OUT;
            break;
        case 2:
            outid = GPIO_MTX_UART2_RTS_OUT;
            break;
        case 3:
            outid = GPIO_MTX_UART3_RTS_OUT;
            break;
        case 4:
            outid = GPIO_MTX_UART4_RTS_OUT;
            break;
        case 5:
            outid = GPIO_MTX_UART5_RTS_OUT;
            break;
        case 6:
            outid = GPIO_MTX_UART6_RTS_OUT;
            break;
        case 7:
            outid = GPIO_MTX_UART7_RTS_OUT;
            break;
        default:
            break;

        }
        break;
    case SIGNAL_SPI_CS:
        switch (number) {
        case 0:
            outid = GPIO_MTX_SPI_M0_CS_OUT;
            break;
        case 1:
            outid = GPIO_MTX_SPI_M1_CS_OUT;
            break;
        case 2:
            outid = GPIO_MTX_SPI_M2_CS_OUT;
            break;
        case 3:
            outid = GPIO_MTX_SPI_M3_CS_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_SPI_CLK:
        switch (number) {
        case 0:
            outid = GPIO_MTX_SPI_M0_CLK_OUT;
            break;
        case 1:
            outid = GPIO_MTX_SPI_M1_CLK_OUT;
            break;
        case 2:
            outid = GPIO_MTX_SPI_M2_CLK_OUT;
            break;
        case 3:
            outid = GPIO_MTX_SPI_M3_CLK_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_SPI_MOSI:
        switch (number) {
        case 0:
            outid = GPIO_MTX_SPI_M0_SO_OUT;
            break;
        case 1:
            outid = GPIO_MTX_SPI_M1_SO_OUT;
            break;
        case 2:
            outid = GPIO_MTX_SPI_M2_SO_OUT;
            break;
        case 3:
            outid = GPIO_MTX_SPI_M3_SO_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_I2C_SCL:
        switch (number) {
        case 0:
            outid = GPIO_MTX_I2C0_SCL_OUT;
            break;
        case 1:
            outid = GPIO_MTX_I2C1_SCL_OUT;
            break;
        case 2:
            outid = GPIO_MTX_I2C2_SCL_OUT;
            break;
        case 3:
            outid = GPIO_MTX_I2C3_SCL_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_I2C_SDA:
        switch (number) {
        case 0:
            outid = GPIO_MTX_I2C0_SDA_OUT;
            break;
        case 1:
            outid = GPIO_MTX_I2C1_SDA_OUT;
            break;
        case 2:
            outid = GPIO_MTX_I2C2_SDA_OUT;
            break;
        case 3:
            outid = GPIO_MTX_I2C3_SDA_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_PWM_A_OUT:
        switch (number) {
        case 0:
            outid = GPIO_MTX_PWM0A_OUT;
            break;
        case 1:
            outid = GPIO_MTX_PWM1A_OUT;
            break;
        case 2:
            outid = GPIO_MTX_PWM2A_OUT;
            break;
        case 3:
            outid = GPIO_MTX_PWM3A_OUT;
            break;
        case 4:
            outid = GPIO_MTX_PWM4A_OUT;
            break;
        case 5:
            outid = GPIO_MTX_PWM5A_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_PWM_B_OUT:
        switch (number) {
        case 0:
            outid = GPIO_MTX_PWM0B_OUT;
            break;
        case 1:
            outid = GPIO_MTX_PWM1B_OUT;
            break;
        case 2:
            outid = GPIO_MTX_PWM2B_OUT;
            break;
        case 3:
            outid = GPIO_MTX_PWM3B_OUT;
            break;
        case 4:
            outid = GPIO_MTX_PWM4B_OUT;
            break;
        case 5:
            outid = GPIO_MTX_PWM5B_OUT;
            break;
        default:
            break;
        }
        break;
    case SIGNAL_LEDC_OUT:
        outid = GPIO_MTX_LED0_OUT + number;
        break;
    case SIGNAL_PA_TX_EN:
        switch (number) {
        case 0:
            outid = GPIO_MTX_TX_EN_A;
            break;
        case 1:
            outid = GPIO_MTX_TX_EN_B;
            break;
        case 2:
            outid = GPIO_MTX_TX_EN_C;
            break;
        }
        break;
    case SIGNAL_PA_RX_EN:
        switch (number) {
        case 0:
            outid = GPIO_MTX_RX_EN_A;
            break;
        case 1:
            outid = GPIO_MTX_RX_EN_B;
            break;
        case 2:
            outid = GPIO_MTX_RX_EN_C;
            break;
        }
        break;
    case SIGNAL_PA_GAIN:
        switch (number) {
        case 0:
            outid = GPIO_MTX_RX_GLNA_0;
            break;
        case 1:
            outid = GPIO_MTX_RX_GLNA_1;
            break;
        case 2:
            outid = GPIO_MTX_RX_GLNA_2;
            break;
        }
        break;
    default:
        break;
    }

    return outid;
}


// 如果buf中的字符全是空白或者以 # 开头则返回1
uint8_t is_comments_and_blankline(char *buf)
{
    char *ptr = buf;

    if (is_whitespace(ptr)) {
        return 1;
    }

    /* the # at the beginning of the line indicates a comment */
    while (*ptr && isspace(*ptr)) {
        ptr++;
    }
    if (*ptr == '#') {
        return 1;
    }

    return 0;
}

// buf 是一行字符 如果这行字符在几种类型之中，返回类型代码，否则返回0xff
uint8_t get_category_info(char *buf)
{
    // 以 空格 分割字符串
    char *start = strtok(buf, " ");
    category_type_t category = CATEGORY_MAX;

    while (*start && isspace(*start)) {
        start++;
    }

    if (!strcmp(start, "general")) {
        category = CATEGORY_GENERAL;
    } else if(!strcmp(start, "rc_hdr")) {
        // 如果类型为 rc_hdr 则初始化一份配置表
        category = CATEGORY_RC_HDR;
        oem_debug_print("============= resource counter:%d =============\n",
            oem_tool.rc_cnt);
        // 一个 iot_board_info_v1_t 结构体即可包含所有的硬件配置
        void *temp = malloc(sizeof(iot_board_info_v1_t));
        if (temp == NULL) {
            die("not enough memory");
        }
        memset(temp, 0xff, sizeof(iot_board_info_v1_t));
        oem_tool.rc_list[oem_tool.rc_cnt] = (iot_board_info_v1_t *)temp;
        oem_tool.rc.rc_ptr = oem_tool.rc_list[oem_tool.rc_cnt];
        oem_tool.rc.device_last = 0;
        oem_tool.rc.pin_idx = 0;
        oem_tool.rc.core_last = 0;
        oem_tool.rc_cnt++;
    } else if (!strcmp(start, "gpio")) {
        category = CATEGORY_GPIO;
    } else if(!strcmp(start, "uart")) {
        category = CATEGORY_UART;
    } else if(!strcmp(start, "pwm")) {
        category = CATEGORY_PWM;
    } else if(!strcmp(start, "adc")) {
        category = CATEGORY_ADC;
    } else if(!strcmp(start, "ledc")) {
        category = CATEGORY_LEDC;
    } else if(!strcmp(start, "spi")) {
        category = CATEGORY_SPI;
    } else if(!strcmp(start, "i2c")) {
        category = CATEGORY_I2C;
    } else if(!strcmp(start, "spinlock")) {
        category = CATEGORY_SPINLOCK;
    } else if(!strcmp(start, "dma")) {
        category = CATEGORY_DMA;
    } else if(!strcmp(start, "gptimer")) {
        category = CATEGORY_GPTIMER;
    } else if(!strcmp(start, "mailbox")) {
           category = CATEGORY_MAILBOX;
    } else if(!strcmp(start, "wdg")) {
        category = CATEGORY_WDG;
    } else if(!strcmp(start, "zc")) {
        category = CATEGORY_ZC;
    } else if(!strcmp(start, "pa")) {
        category = CATEGORY_PA;
    } else {
        oem_debug_print("get category info fail, buf:%s\n", buf);
        return category;
    }

    oem_debug_print(" category info, buf:%s, result:%s\n", start,
        g_category_string[category]);
    return category;
}

// 把配置写入 iot_board_info_v1_t 结构体中
// category 类型， number 外设或内设的编号， core 使用的核心， purpose 用途
uint8_t set_peripheral_allot(uint8_t category, uint8_t number,
    uint8_t core, uint8_t purpose)
{
    switch (category) {
    case CATEGORY_GPIO:
        for (uint8_t i = 0; i < IOT_PIN_MAX_NUM_V1; i++) {
            // 如果找到已配置的编号相同的gpio或者找到一个未配置的gpio，返回其在数组中的index
            if (oem_tool.rc.rc_ptr->pin[i].gpio == number ||
                oem_tool.rc.rc_ptr->pin[i].gpio == 0xff) {
                oem_tool.rc.pin_idx = i;
                break;
            }
            if (i == IOT_PIN_MAX_NUM_V1 - 1) {
                die("not enough structural space, line:%d", oem_tool.line_num);
            }
        }
        oem_debug_print("pin array current index:%d\n", oem_tool.rc.pin_idx);
        /* gpio index maybe greater than IOT_PIN_MAX_NUM_V1 */
        // 配置这个gpio
        oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].gpio = number;
        oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].core = core;
        oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].purpose = purpose;
        if (oem_tool.rc.rc_ptr->hdr.mode) {
            /* clear the peripheral signals that may be bound */
            oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].inid = 0xff;
            oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].outid = 0xff;
            oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].func = 0xff;
        }
        break;
    case CATEGORY_UART:
        oem_tool.rc.rc_ptr->uart[number].core = core;
        oem_tool.rc.rc_ptr->uart[number].purpose = purpose;
        break;
    case CATEGORY_PWM:
        oem_tool.rc.rc_ptr->pwm[number].core = core;
        oem_tool.rc.rc_ptr->pwm[number].purpose = purpose;
        break;
    case CATEGORY_ADC:
        oem_tool.rc.rc_ptr->adc[number].core = core;
        oem_tool.rc.rc_ptr->adc[number].purpose = purpose;
        break;
    case CATEGORY_LEDC:
        oem_tool.rc.rc_ptr->ledc[number].core = core;
        oem_tool.rc.rc_ptr->ledc[number].purpose = purpose;
        break;
    case CATEGORY_SPI:
        oem_tool.rc.rc_ptr->spi[number].core = core;
        oem_tool.rc.rc_ptr->spi[number].purpose = purpose;
        break;
    case CATEGORY_I2C:
        oem_tool.rc.rc_ptr->i2c[number].core = core;
        oem_tool.rc.rc_ptr->i2c[number].purpose = purpose;
        break;
    case CATEGORY_SPINLOCK:
        oem_tool.rc.rc_ptr->spinlock[number].core = core;
        oem_tool.rc.rc_ptr->spinlock[number].purpose = purpose;
        break;
    case CATEGORY_DMA:
        oem_tool.rc.rc_ptr->dma[number].core = core;
        oem_tool.rc.rc_ptr->dma[number].purpose = purpose;
        break;
    case CATEGORY_GPTIMER:
        oem_tool.rc.rc_ptr->gptimer[number].core = core;
        oem_tool.rc.rc_ptr->gptimer[number].purpose = purpose;
        break;
    case CATEGORY_MAILBOX:
        oem_tool.rc.rc_ptr->mailbox[number].core = core;
        oem_tool.rc.rc_ptr->mailbox[number].purpose = purpose;
        break;
    case CATEGORY_WDG:
        oem_tool.rc.rc_ptr->wdg[number].core = core;
        oem_tool.rc.rc_ptr->wdg[number].purpose = purpose;
        break;
    default:
        break;
    }
    oem_debug_print("  peripheral allot, category:%s, number:%d, core:%d, "
        "purpose:%d\n", g_category_string[category], number, core, purpose);
    return 0;
}

// 如果外设或内设编号number大于范围 则退出程序
void rc_quantity_boundary_check(uint8_t category, uint8_t number)
{
    uint8_t out_of_bounds = 0;

    switch (category) {
    case CATEGORY_GPIO:
        out_of_bounds = (number >= RC_TOTAL_GPIO);
        break;
    case CATEGORY_UART:
        out_of_bounds = (number >= RC_TOTAL_UART);
        break;
    case CATEGORY_PWM:
        out_of_bounds = (number >= RC_TOTAL_PWM);
        break;
    case CATEGORY_ADC:
        out_of_bounds = (number >= RC_TOTAL_ADC);
        break;
    case CATEGORY_LEDC:
        out_of_bounds = (number >= RC_TOTAL_LEDC);
        break;
    case CATEGORY_SPI:
        out_of_bounds = (number >= RC_TOTAL_SPI);
        break;
    case CATEGORY_I2C:
        out_of_bounds = (number >= RC_TOTAL_I2C);
        break;
    case CATEGORY_SPINLOCK:
        out_of_bounds = (number >= RC_TOTAL_SPINLOCK);
        break;
    case CATEGORY_DMA:
        out_of_bounds = (number >= RC_TOTAL_DMA);
        break;
    case CATEGORY_GPTIMER:
        out_of_bounds = (number >= RC_TOTAL_GPTIMER);
        break;
    case CATEGORY_MAILBOX:
        out_of_bounds = (number >= RC_TOTAL_MAILBOX);
        break;
    case CATEGORY_WDG:
        out_of_bounds = (number >= RC_TOTAL_WDG);
        break;
    case CATEGORY_ZC:
        out_of_bounds = (number >= RC_TOTAL_ZC);
        break;
    case CATEGORY_PA:
        out_of_bounds = (number >= RC_TOTAL_PA);
        break;
    }

    if (out_of_bounds) {
        die("device number exceeds maximum, device:%s, number:%d\n",
            g_category_string[category], number);
    }

    oem_debug_print("====== %s, number:%d, out:%d\n",
        g_category_string[category], number, out_of_bounds);
}

// 设置gpio的参数到 iot_board_info_v1_t 结构体中，str是从配置文件中读取的关键字
// 通过这个函数设置的gpio，func都是0
uint8_t set_gpio_matrix_signal(uint8_t category, uint8_t number,
    char *str, uint8_t gpio, uint8_t core)
{
    uint8_t sig_type = SIGNAL_MAX;
    uint8_t inid = 0xff, outid = 0xff;
    // func好像没用到 都是返回0
    uint8_t func = gpio_func_sel(gpio);

    if (!strcmp(str, "tx")) {
        if (category == CATEGORY_UART) {
            sig_type = SIGNAL_UART_TX;
        }
    } else if (!strcmp(str, "rx")) {
        if (category == CATEGORY_UART) {
            sig_type = SIGNAL_UART_RX;
        }
    } else if (!strcmp(str, "rts")) {
        if (category == CATEGORY_UART) {
            sig_type = SIGNAL_UART_RTS;
        }
    } else if (!strcmp(str, "cts")) {
        if (category == CATEGORY_UART) {
            sig_type = SIGNAL_UART_CTS;
        }
    } else if (!strcmp(str, "cs")) {
        if (category == CATEGORY_SPI) {
            sig_type = SIGNAL_SPI_CS;
        }
    } else if (!strcmp(str, "clk")) {
        if (category == CATEGORY_SPI) {
            sig_type = SIGNAL_SPI_CLK;
        }
    } else if (!strcmp(str, "miso")) {
        if (category == CATEGORY_SPI) {
            sig_type = SIGNAL_SPI_MISO;
        }
    } else if (!strcmp(str, "mosi")) {
        if (category == CATEGORY_SPI) {
            sig_type = SIGNAL_SPI_MOSI;
        }
    } else if (!strcmp(str, "sda")) {
        if (category == CATEGORY_I2C) {
            sig_type = SIGNAL_I2C_SDA;
        }
    } else if (!strcmp(str, "scl")) {
        if (category == CATEGORY_I2C) {
            sig_type = SIGNAL_I2C_SCL;
        }
    } else if (!strcmp(str, "pwma")) {
        if (category == CATEGORY_PWM) {
            sig_type = SIGNAL_PWM_A_OUT;
        }
    } else if (!strcmp(str, "pwmb")) {
        if (category == CATEGORY_PWM) {
            sig_type = SIGNAL_PWM_B_OUT;
        }
    } else if (!strcmp(str, "ledout")) {
        if (category == CATEGORY_LEDC) {
            sig_type = SIGNAL_LEDC_OUT;
        }
    } else if (starts_with(str, "up_")) {
        if (category == CATEGORY_ZC) {
            sig_type = SIGNAL_ZC_UP;
            number = atoi(&str[iot_strlen("up_")]);
            rc_quantity_boundary_check(category, number);
        }
    } else if (starts_with(str, "down_")) {
        if (category == CATEGORY_ZC) {
            sig_type = SIGNAL_ZC_DOWN;
            number = atoi(&str[iot_strlen("down_")]);
            rc_quantity_boundary_check(category, number);
        }
    } else if (starts_with(str, "tx_en_")) {
        if (category == CATEGORY_PA) {
            sig_type = SIGNAL_PA_TX_EN;
            number = atoi(&str[iot_strlen("tx_en_")]);
            rc_quantity_boundary_check(category, number);
        }
    } else if (starts_with(str, "rx_en_")) {
        if (category == CATEGORY_PA) {
            sig_type = SIGNAL_PA_RX_EN;
            number = atoi(&str[iot_strlen("rx_en_")]);
            rc_quantity_boundary_check(category, number);
        }
    } else if (starts_with(str, "gain_")) {
        if (category == CATEGORY_PA) {
            sig_type = SIGNAL_PA_GAIN;
            number = atoi(&str[iot_strlen("gain_")]);
            rc_quantity_boundary_check(category, number);
        }
    }

    if (sig_type == SIGNAL_MAX) {
        die("signal type error, category:%s, signal str:%s\n",
            g_category_string[category], str);
    }

    outid = get_matrix_signal_outid(sig_type, number);
    inid = get_matrix_signal_inid(sig_type, number);

    // 找到gpio在结数组中的index
    for (uint8_t i = 0; i < IOT_PIN_MAX_NUM_V1; i++) {
        if (oem_tool.rc.rc_ptr->pin[i].gpio == gpio ||
            oem_tool.rc.rc_ptr->pin[i].gpio == 0xff) {
            oem_tool.rc.pin_idx = i;
            break;
        }
        if (i == IOT_PIN_MAX_NUM_V1 - 1) {
            die("not enough structural space, line:%d", oem_tool.line_num);
        }
    }
    oem_debug_print("pin array current index:%d\n", oem_tool.rc.pin_idx);
    /* gpio index maybe greater than IOT_PIN_MAX_NUM_V1 */
    oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].gpio = gpio;
    oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].func = func;
    /* gpio绑定多个信号 */
    if (inid != 0xff) {
        oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].inid = inid;
    }
    if (outid != 0xff) {
        oem_tool.rc.rc_ptr->pin[oem_tool.rc.pin_idx].outid = outid;
    }

    oem_debug_print("   signal matrix info, buf:%s, category:%s, signal:%s, "
        "number:%d, gpio:%d, core:%d, inid:%d, outid:%d\n", str,
        g_category_string[category], g_signal_string[sig_type],
        number, gpio, core, inid, outid);

    return 0;
}


// 解析细节，差分模式是把之前的拷贝一份再把改动部分覆盖之前的
uint8_t get_detail_info(char *buf, uint8_t category)
{
    char *str_ptr[3] = {0};
    char *split_str = " ";
    uint8_t is_peripheral_gpio_map = 1;

    /* split string */
    str_ptr[0] = strtok(buf, split_str);
    str_ptr[1] = strtok(NULL, split_str);
    str_ptr[2] = strtok(NULL, split_str);

    /* special category */
    if (category == CATEGORY_GENERAL) {
        if (!strcmp(str_ptr[0], "bid")) {
            // board_id 可以用于区分模块用途 是sta iic 3ps还是cco
            // 比subid 更详细 subid用于区分芯片
            oemcfg.board_id = atoi(str_ptr[1]);
        } else if (!strcmp(str_ptr[0], "mid")) {
            // 0:sta 1:cco 2:iic 3:3ps
            oemcfg.base_cfg.module_type = atoi(str_ptr[1]);
        } else if (!strcmp(str_ptr[0], "vid")) {
            /* vid is text data, two characters */
            // 芯片厂家缩写
            oemcfg.misc_cfg.vendor_id = htons(*(uint16_t*)str_ptr[1]);
        } else if (!strcmp(str_ptr[0], "fver")) {
            // ?
            oemcfg.board_cfg_ver = atoi(str_ptr[1]);
        }
        return 0;
    } else if (category == CATEGORY_RC_HDR) {
        if (!strcmp(str_ptr[0], "hw_ver")) {
            // 硬件识别码
            oem_tool.rc.rc_ptr->hdr.hw_version = oem_atoi(str_ptr[1]);
        } else if (!strcmp(str_ptr[0], "mode")) {
            oem_tool.rc.rc_ptr->hdr.mode = atoi(str_ptr[1]) ? 1 : 0;
#if 0
            /* currently, only differential mode is supported */
            if ((oem_tool.rc_cnt != 1) && (!oem_tool.rc.rc_ptr->hdr.mode)) {
                die("not diff mode, line:%d", oem_tool.line_num);
            }
#endif
        } else if (!strcmp(str_ptr[0], "d_hw_ver")) {
            uint32_t diff_hw_ver = oem_atoi(str_ptr[1]);
            oem_tool.rc.rc_ptr->hdr.diff_hw_ver = diff_hw_ver;
            if (oem_tool.rc.rc_ptr->hdr.mode) {
                uint8_t i;
                uint8_t len_hdr = sizeof(iot_oem_rc_hdr_v1_t);
                // 找到 diff_hw_ver 所在的 iot_board_info_v1_t 结构体
                for (i = 0; i < oem_tool.rc_cnt; i++) {
                    if (oem_tool.rc_list[i]->hdr.hw_version == diff_hw_ver) {
                        break;
                    }
                }
                if (i == oem_tool.rc_cnt) {
                    die("diff hw version not match, line:%d", oem_tool.line_num);
                }
                // 把之前的复制一份
                memcpy((uint8_t *)oem_tool.rc.rc_ptr + len_hdr,
                    (uint8_t *)oem_tool.rc_list[i] + len_hdr,
                    sizeof(iot_board_info_v1_t) - len_hdr);
            }
        }
        return 0;
    }

    /* peripheral category */
    if (isdigit(*str_ptr[0])) {
        is_peripheral_gpio_map = 0;
    }

    if (is_peripheral_gpio_map) {
        // 通过外设来设置gpio
        uint8_t gpio = atoi(str_ptr[1]);
        if (set_gpio_matrix_signal(category, oem_tool.rc.device_last, str_ptr[0],
            gpio, oem_tool.rc.core_last)) {
            die("signal info error, line:%d", oem_tool.line_num);
        }
    } else {
        // 配置gpio
        uint8_t number = atoi(str_ptr[0]);
        uint8_t core = atoi(str_ptr[1]);
        uint8_t purpose = atoi(str_ptr[2]);
        rc_quantity_boundary_check(category, number);
        set_peripheral_allot(category, number, core, purpose);
        oem_tool.rc.device_last = number;
        oem_tool.rc.core_last = core;
    }

    return 0;
}


uint8_t genereate_diff_content(iot_board_info_v1_t *rc,
    iot_board_info_v1_t *rc_d)
{
    uint16_t i, j, idx_0, idx_1, idx_d;
    uint8_t len_hdr = sizeof(iot_oem_rc_hdr_v1_t);
    uint32_t len_rc = sizeof(iot_board_info_v1_t);
    uint8_t len_diff = sizeof(iot_oem_rc_diff_v1_t);
    uint8_t *p_rc = (uint8_t *)rc;
    uint8_t *p_rc_d = (uint8_t *)rc_d;
    iot_oem_rc_diff_v1_t *diff;

    /* save header info */
    memcpy(&oem_tool.buf.buf[oem_tool.buf.len_total], &rc->hdr, len_hdr);
    oem_tool.buf.len_total += len_hdr;

    for (i = len_hdr; i < len_rc; i++) {
        /* If the interval between two adjacent differential data is less than
         * 4 bytes, the space used to save the data together is smaller.
         */
        if (p_rc[i] != p_rc_d[i]) {
            idx_0 = i;
            idx_1 = idx_0 + 1;  //prevents the last byte from being unequal
again:
            for (j = i + 1; j < len_rc; j++) {
                if (p_rc[j] != p_rc_d[j]) {
                    if (j - i > 4) {    //store the two sections separately
                        for (j = i + 1; j < len_rc; j++) {
                            if (p_rc[j] == p_rc_d[j]) {
                                idx_1 = j;
                                break;
                            }
                        }
                    } else {    //store the two sections together
                        i = j;
                        goto again;
                    }
                    break;
                } else {
                    if (j == len_rc - 1) {  //the last unequal block
                        for (j = i + 1; j < len_rc; j++) {
                            if (p_rc[j] == p_rc_d[j]) {
                                idx_1 = j;
                                break;
                            }
                        }
                        break;
                    }
                }
            }
            i = idx_1;
            idx_d = idx_1 - idx_0;
            diff = (iot_oem_rc_diff_v1_t *)&oem_tool.buf.buf[\
                oem_tool.buf.len_total];
            oem_tool.buf.len_total += len_diff;
            diff->offset = idx_0;
            diff->length = idx_d;
            memcpy(&oem_tool.buf.buf[oem_tool.buf.len_total], &p_rc[idx_0], idx_d);
            oem_tool.buf.len_total += idx_d;

            oem_debug_print("find diff data, offset:%d, length:%d, buf offset:%d\n",
                diff->offset, diff->length, oem_tool.buf.len_total);
            oem_debug_print(" curr data: ");
            for (uint16_t m = 0; m < diff->length; m++) {
                oem_debug_print("%02x ", p_rc[diff->offset + m]);
            }
            oem_debug_print("\n");
            oem_debug_print(" diff data: ");
            for (uint16_t m = 0; m < diff->length; m++) {
                oem_debug_print("%02x ", p_rc_d[diff->offset + m]);
            }
            oem_debug_print("\n");
        }
    }

    return 0;
}

uint8_t rc_data_merge()
{
    uint16_t buf_index_last;
    uint8_t index, diff_index;

    for (index = 0; index < oem_tool.rc_cnt; index++) {
        buf_index_last = oem_tool.buf.len_total;
        if (oem_tool.rc_list[index]->hdr.mode == 0) {
            if (index != 0) {
                /* save the complete resource table */
                oem_debug_print("save complete rc data\n");
                memcpy(&oem_tool.buf.buf[oem_tool.buf.len_total],
                    &oem_tool.rc_list[index]->hdr, sizeof(iot_board_info_v1_t));
                oem_tool.buf.len_total += sizeof(iot_board_info_v1_t);
            }
            oem_tool.rc_list[index]->hdr.length = sizeof(iot_board_info_v1_t) -
                sizeof(iot_oem_rc_hdr_v1_t);
        } else {
            for (diff_index = 0; diff_index < oem_tool.rc_cnt; diff_index++) {
                if (oem_tool.rc_list[diff_index]->hdr.hw_version ==
                    oem_tool.rc_list[index]->hdr.diff_hw_ver) {
                    break;
                }
            }
            if (diff_index == oem_tool.rc_cnt) {
                die("diff hw version(0x%08x) not match\n",
                    oem_tool.rc_list[index]->hdr.diff_hw_ver);
            }
            /* save the difference data */
            oem_debug_print("save difference data\n");
            genereate_diff_content(oem_tool.rc_list[index],
                oem_tool.rc_list[diff_index]);
            oem_tool.rc_list[index]->hdr.length = oem_tool.buf.len_total -
                buf_index_last - sizeof(iot_oem_rc_hdr_v1_t);
            oem_debug_print("genereate diff data succeed, len:%d,(%d - %d)\n",
                oem_tool.rc_list[index]->hdr.length, oem_tool.buf.len_total,
                buf_index_last);
        }

        /* oem partition size is 4K, including image header(64 bytes) and an
         * iot_oem_cfg_t structure. the remaining space holds differential data.
         */
        if (oem_tool.buf.len_total > 4096 - sizeof(iot_oem_cfg_t) - 64) {
            die("diff data length exceeded the limit\n");
        }

        /* fill header information (crc and offset) */
        if (oem_tool.rc_list[index + 1] != 0) {
            oem_tool.rc_list[index]->hdr.have_next = 1;
        } else {
            oem_tool.rc_list[index]->hdr.have_next = 0;
        }
        oem_tool.rc_list[index]->hdr.crc = \
            iot_getcrc32((uint8_t *)&oem_tool.rc_list[index]->hdr +
            sizeof(uint32_t), sizeof(iot_board_info_v1_t) - sizeof(uint32_t));

        /* copy header info again */
        memcpy(&oem_tool.buf.buf[buf_index_last],
            &oem_tool.rc_list[index]->hdr, sizeof(iot_oem_rc_hdr_v1_t));
    }

    /* The first resource is put into the OEM architecture */
    memcpy(&oemcfg.board_cfg_v1, oem_tool.rc_list[0],
        sizeof(iot_board_info_v1_t));

    return 0;
}

void load_database_hw(const char *filename)
{
    FILE *fp;
    char buf[2048];
    category_type_t category;

    fp = fopen(filename, "r");
    if (fp == NULL) {
        die ("error opening %s: %s", filename, strerror (errno));
    }

    memset(oem_tool.buf.buf, 0xff, sizeof(oem_tool.buf.buf));

    while (fgets(buf, sizeof(buf), fp) != NULL) {
        oem_tool.line_num++;

        if (is_comments_and_blankline(buf)) {
            continue;
        }
        oem_debug_print("--> line data:%s", buf);

        chomp_trailing_whitespace(buf);

        if (!isspace(buf[0])){
            category = get_category_info(buf);
            if (category == CATEGORY_MAX) {
                die("ini file category data error, lines:%d", oem_tool.line_num);
            }
        } else {
            get_detail_info(buf, category);
        }
    }

    rc_data_merge();

    fclose (fp);
}

void save_database_hw(const char *filename)
{
    FILE *fp;
    uint8_t *buf = (uint8_t*)&oemcfg;

    if (filename == NULL) {
        fp = fopen("oem.bin", "wb");
    } else {
        fp = fopen(filename, "wb");
    }

    //printf("oem len:%d\n", (uint32_t)sizeof(iot_oem_cfg_t));
    oemcfg.base_cfg.oem_crc = iot_getcrc8(buf + sizeof(uint8_t),
        sizeof(iot_oem_cfg_t) - sizeof(uint8_t));

    if (fp == NULL)
        die ("error write oem.bin: %s", strerror(errno));

    fwrite(buf, sizeof(iot_oem_cfg_t), 1, fp);
    if (oem_tool.buf.len_total) {
        // oem_tool.buf中存储的是差分后的配置信息 每个差分都是原配置的一个副本修改差异值
        oem_debug_print("find diff data, write to file\n");
        fwrite(oem_tool.buf.buf, sizeof(uint8_t), oem_tool.buf.len_total, fp);
    }

    fclose(fp);
}

void oem_resource_info_dump(iot_board_info_v1_t *ptr_rc)
{
    uint8_t i;
    uint32_t crc;

    printf("resource info, crc:0x%08x, hw_version:0x%08x, mode:%d, "
        "diff hw_ver:0x%08x, length:%d, have next:%d\n",
        ptr_rc->hdr.crc, ptr_rc->hdr.hw_version, ptr_rc->hdr.mode,
        ptr_rc->hdr.diff_hw_ver, ptr_rc->hdr.length, ptr_rc->hdr.have_next);
    // 计算 iot_board_info_v1_t 结构体除crc字段其他部分的crc32
    crc = iot_getcrc32((uint8_t *)&ptr_rc->hdr + sizeof(uint32_t),
        sizeof(iot_board_info_v1_t) - sizeof(uint32_t));
    if (crc != ptr_rc->hdr.crc) {
        die("crc error, hdr:0x%08x, cal:0x%08x", ptr_rc->hdr.crc, crc);
    } else {
        printf("resource crc check pass\n");
    }

    for (i = 0; i < IOT_PIN_MAX_NUM_V1; i++) {
        if (ptr_rc->pin[i].gpio == 0xff) {
            continue;
        }
        printf("pin info, index:%d, gpio:%d, core:%d, func:%d, inid:%d, outid:%d,"
            " purpose:%d\n", i, ptr_rc->pin[i].gpio, ptr_rc->pin[i].core,
            ptr_rc->pin[i].func, ptr_rc->pin[i].inid, ptr_rc->pin[i].outid,
            ptr_rc->pin[i].purpose);
    }

    for (i = 0; i < IOT_UART_MAX_NUM_V1; i++) {
        if (ptr_rc->uart[i].core == 0xff) {
            continue;
        }
        printf("uart info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->uart[i].core, ptr_rc->uart[i].purpose);
    }

    for (i = 0; i < IOT_PWM_MAX_NUM_V1; i++) {
        if (ptr_rc->pwm[i].core == 0xff) {
            continue;
        }
        printf("pwm info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->pwm[i].core, ptr_rc->pwm[i].purpose);
    }

    for (i = 0; i < IOT_ADC_MAX_NUM_V1; i++) {
        if (ptr_rc->adc[i].core == 0xff) {
            continue;
        }
        printf("adc info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->adc[i].core, ptr_rc->adc[i].purpose);
    }

    for (i = 0; i < IOT_LEDC_MAX_NUM_V1; i++) {
        if (ptr_rc->ledc[i].core == 0xff) {
            continue;
        }
        printf("ledc info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->ledc[i].core, ptr_rc->ledc[i].purpose);
    }

    for (i = 0; i < IOT_SPI_MAX_NUM_V1; i++) {
        if (ptr_rc->spi[i].core == 0xff) {
            continue;
        }
        printf("spi info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->spi[i].core, ptr_rc->spi[i].purpose);
    }

    for (i = 0; i < IOT_I2C_MAX_NUM_V1; i++) {
        if (ptr_rc->i2c[i].core == 0xff) {
            continue;
        }
        printf("i2c info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->i2c[i].core, ptr_rc->i2c[i].purpose);
    }

    for (i = 0; i < IOT_SPINLOCK_MAX_NUM_V1; i++) {
        if (ptr_rc->spinlock[i].core == 0xff) {
            continue;
        }
        printf("spinlock info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->spinlock[i].core, ptr_rc->spinlock[i].purpose);
    }

    for (i = 0; i < IOT_DMA_MAX_NUM_V1; i++) {
        if (ptr_rc->dma[i].core == 0xff) {
            continue;
        }
        printf("dma info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->dma[i].core, ptr_rc->dma[i].purpose);
    }

    for (i = 0; i < IOT_GPTIMER_MAX_NUM_V1; i++) {
        if (ptr_rc->gptimer[i].core == 0xff) {
            continue;
        }
        printf("gptimer info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->gptimer[i].core, ptr_rc->gptimer[i].purpose);
    }

    for (i = 0; i < IOT_MAILBOX_MAX_NUM_V1; i++) {
        if (ptr_rc->mailbox[i].core == 0xff) {
            continue;
        }
        printf("mailbox info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->mailbox[i].core, ptr_rc->mailbox[i].purpose);
    }

    for (i = 0; i < IOT_WDG_MAX_NUM_V1; i++) {
        if (ptr_rc->wdg[i].core == 0xff) {
            continue;
        }
        printf("wdg info, index:%d, core:%d, purpose:%d\n",
            i, ptr_rc->wdg[i].core, ptr_rc->wdg[i].purpose);
    }
    printf("\n");
}

void oem_bin_file_parse_hw_all()
{
    uint8_t i;
    uint8_t len_hdr = sizeof(iot_oem_rc_hdr_v1_t);
    uint8_t diff_buf[sizeof(iot_board_info_v1_t)];
    uint8_t diff_idx;
    uint16_t diff_data_len;
    uint32_t diff_hw_ver;
    iot_oem_rc_hdr_v1_t *hdr_ptr;

    /* get all resource */
    oem_tool.rc_list[oem_tool.rc_cnt] = &oemcfg.board_cfg_v1;
again:
    // 如果存在下一个的话，读取下一个
    if (oem_tool.rc_list[oem_tool.rc_cnt]->hdr.have_next) {
        printf("find next rc, offset:%d\n", oem_tool.buf.len_total);
        oem_tool.rc_cnt++;
        void *temp = malloc(sizeof(iot_board_info_v1_t));
        if (temp == NULL) {
            die("not enough memory");
        }
        oem_tool.rc_list[oem_tool.rc_cnt] = (iot_board_info_v1_t *)temp;
        // 读取buf中剩余的空间
        hdr_ptr = (iot_oem_rc_hdr_v1_t *)&oem_tool.buf.buf[oem_tool.buf.len_total];

        if (hdr_ptr->mode == 0) {
            printf("full resource table\n");
            memcpy(temp, &oem_tool.buf.buf[oem_tool.buf.len_total],
                sizeof(iot_board_info_v1_t));
            oem_tool.buf.len_total += sizeof(iot_board_info_v1_t);
            goto again;
        }

        printf("differential resource table\n");
        /* copy header */
        memcpy(temp, &oem_tool.buf.buf[oem_tool.buf.len_total], len_hdr);
        oem_tool.buf.len_total += len_hdr;
        diff_hw_ver = oem_tool.rc_list[oem_tool.rc_cnt]->hdr.diff_hw_ver;
        for (diff_idx = 0; diff_idx < oem_tool.rc_cnt; diff_idx++) {
            if (oem_tool.rc_list[diff_idx]->hdr.hw_version == diff_hw_ver) {
                break;
            }
        }
        if (diff_idx >= oem_tool.rc_cnt) {
            die("diff hw version(0x%08x) not match, current rc cnt:%d\n",
                diff_hw_ver, oem_tool.rc_cnt);
        }
        /* copy diff source data */
        memcpy((uint8_t *)oem_tool.rc_list[oem_tool.rc_cnt] + len_hdr,
            (uint8_t *)oem_tool.rc_list[diff_idx] + len_hdr,
            sizeof(iot_board_info_v1_t) - len_hdr);
        /* copy diff data */
        diff_data_len = oem_tool.rc_list[oem_tool.rc_cnt]->hdr.length;
        memcpy(diff_buf, &oem_tool.buf.buf[oem_tool.buf.len_total], diff_data_len);
        oem_tool.buf.len_total += diff_data_len;
        /* restore differential data */
        // 这里可以支持多个差异二进制片段
        i = 0;
        while (i < diff_data_len) {
            iot_oem_rc_diff_v1_t *diff_temp =
                (iot_oem_rc_diff_v1_t *)&diff_buf[i];
            uint16_t len_temp = diff_temp->length;
            uint16_t offset_temp = diff_temp->offset;
            memcpy((uint8_t *)oem_tool.rc_list[oem_tool.rc_cnt] + offset_temp,
                diff_temp->data, len_temp);
            i += sizeof(iot_oem_rc_diff_v1_t) + len_temp;
        }
        goto again;
    }

    printf("total of %d resource table\n", oem_tool.rc_cnt + 1);

    for (uint8_t cnt = 0; cnt < oem_tool.rc_cnt + 1; cnt++) {
        iot_board_info_v1_t *ptr_rc = oem_tool.rc_list[cnt];
        /* dump board resource info */
        printf("============= resource counter:%d =============\n", cnt);
        oem_resource_info_dump(ptr_rc);
    }
}

void oem_bin_file_parse_hw_specific(uint8_t *buf, uint32_t hw_ver)
{
    int i = 0;
    iot_board_info_v1_t *ptr_rc;
    iot_oem_rc_hdr_v1_t *ptr_hdr;
    uint32_t hw_ver_rc, hw_ver_cal;
    uint8_t cnt_rc = 1;
    uint16_t offset = 0;
    uint16_t *offset_array;
    uint8_t *diff_idx_array;
    iot_board_info_v1_t rc_info = {0};
    uint8_t buf_oem[4096 - sizeof(iot_oem_cfg_t) - 64] = {0};
    iot_oem_cfg_t *oem_cfg;

    printf("parse hw version:0x%08x\n", hw_ver);
    oem_cfg = (iot_oem_cfg_t *)buf;
    ptr_rc = &oem_cfg->board_cfg_v1;
    memcpy(&rc_info, ptr_rc, sizeof(iot_board_info_v1_t));
    memcpy(buf_oem, buf + sizeof(iot_oem_cfg_t), sizeof(buf_oem));

    hw_ver_cal = hw_ver;
    ptr_hdr = &ptr_rc->hdr;
    hw_ver_rc = ptr_hdr->hw_version;
    /* fund the matching resource table */
hdr_check:
    if (hw_ver_cal != hw_ver_rc) {
        if (ptr_hdr->have_next == 0) {
            die("resource does not match but no other resource\n");
        }
        cnt_rc++;
        ptr_hdr = (iot_oem_rc_hdr_v1_t *)&buf_oem[offset];
        offset += ptr_hdr->length + sizeof(iot_oem_rc_hdr_v1_t);
        hw_ver_rc = ptr_hdr->hw_version;
        goto hdr_check;
    }
    printf("match resource counter:%d\n", cnt_rc);

    /* gets information about all matched headers */
    if (cnt_rc >= 2) {
        uint8_t cnt_diff_deep = 0;
        /* Not differential mode */
        if (ptr_hdr->mode == 0) {
            memcpy(&rc_info, ptr_hdr, sizeof(iot_board_info_v1_t));
            goto dump;
        }
        /* differential mode */
        offset_array = (uint16_t *)malloc(sizeof(uint16_t) * cnt_rc);
        diff_idx_array = (uint8_t *)malloc(sizeof(uint8_t) * cnt_rc);
        if (offset_array == NULL || diff_idx_array == NULL) {
            die("malloc memory failed\n");
        }
        offset = 0;
        /* get resource header information offset in diff data buffer */
        for (i = 1; i < cnt_rc; i++) {  //skip the first full resource table
            offset_array[i] = offset;
            ptr_hdr = (iot_oem_rc_hdr_v1_t *)&buf_oem[offset];
            offset += ptr_hdr->length + sizeof(iot_oem_rc_hdr_v1_t);
        }
        /* get the difference mapping table */
        for (i = cnt_rc - 1; i > 0;) {
            uint8_t j;
            uint32_t hw_ver_diff;
            ptr_hdr = (iot_oem_rc_hdr_v1_t *)&buf_oem[offset_array[i]];
            hw_ver_diff = ptr_hdr->diff_hw_ver;
            diff_idx_array[cnt_diff_deep] = i;
            cnt_diff_deep++;
            for (j = i - 1; j > 0; j--) {
                ptr_hdr = (iot_oem_rc_hdr_v1_t *)&buf_oem[offset_array[j]];
                if (ptr_hdr->hw_version == hw_ver_diff) {
                    i = j;
                    oem_debug_print("find father rc table, index:%d\n", i);
                    if (ptr_hdr->mode == 0) {
                        oem_debug_print("father is full rc table\n");
                        memcpy(&rc_info, ptr_hdr, sizeof(iot_board_info_v1_t));
                        j = 0;
                    }
                    break;
                }
            }
            if (j == 0) {
                oem_debug_print("find full rc table, as root\n");
                break;
            }
        }
        printf("get diff deep:%d, array:", cnt_diff_deep);
        for (i = 0; i < cnt_diff_deep; i++) {
            printf("%d, ", diff_idx_array[i]);
        }
        printf("\n");
        /* get diff resource table information */
        for (i = cnt_diff_deep - 1; i >= 0; i--) {
            uint16_t offset_temp;
            iot_oem_rc_diff_v1_t *ptr_diff;
            uint8_t diff_idx = diff_idx_array[i];
            ptr_hdr = (iot_oem_rc_hdr_v1_t *)&buf_oem[offset_array[diff_idx]];
            /* copy header info */
            memcpy(&rc_info, ptr_hdr, sizeof(iot_oem_rc_hdr_v1_t));
            /* replace diff data */
            offset = offset_array[diff_idx] + sizeof(iot_oem_rc_hdr_v1_t);
            offset_temp = offset;
            while (offset_temp < offset + ptr_hdr->length) {
                ptr_diff = (iot_oem_rc_diff_v1_t *)&buf_oem[offset_temp];
                memcpy((uint8_t *)&rc_info + ptr_diff->offset,
                    ptr_diff->data, ptr_diff->length);
                offset_temp += sizeof(iot_oem_rc_diff_v1_t) + ptr_diff->length;
            }
        }
    }

dump:
    printf("============= resource hw version:0x%08x =============\n", hw_ver);
    oem_resource_info_dump(&rc_info);
}

// 读取bin文件并解析
void oem_bin_file_parse_hw(const char *filename)
{
    FILE *fp;
    uint8_t crc;

    if (filename == NULL) {
        fp = fopen("oem.bin", "rb");
    } else {
        fp = fopen (filename, "rb");
    }
    if (fp == NULL) {
        die("open oem bin file(%s) failed, %s", filename, strerror(errno));
    }
    printf("open oem bin file(%s) succeed\n", filename);

    /* read oem bin file all data */
    // 读取4k个字节的oem数据
    fread(oem_tool.buf.buf, sizeof(oem_tool.buf.buf), 1, fp);
    /* not include image header information by default */
    // 把第一个配置信息复制到oemcfg结构体
    memcpy((void*)&oemcfg, oem_tool.buf.buf, sizeof(iot_oem_cfg_t));
    // 修改当前指针为 iot_oem_cfg_t 结构体的长度
    oem_tool.buf.len_total += sizeof(iot_oem_cfg_t);
    // 计算 iot_oem_cfg_t 结构体的crc8 此结构体的第一个字节为crc值
    crc = iot_getcrc8((uint8_t*)&oemcfg + sizeof(uint8_t),
        sizeof(iot_oem_cfg_t) - sizeof(uint8_t));
    if (crc != oemcfg.base_cfg.oem_crc) {
        die("oem bin file crc check error, cal:0x%x, file:0x%x",
            crc, oemcfg.base_cfg.oem_crc);
    }
    /* general information */
    printf("board id:%d\n", oemcfg.board_id);
    printf("module type:%d\n", oemcfg.base_cfg.module_type);
    /* [TODO]: vendor id need byte order conversion and limited two characters */
    printf("vendor id:%s\n", (char*)&oemcfg.misc_cfg.vendor_id);
    printf("resource version:%d\n", oemcfg.board_cfg_ver);

    oem_bin_file_parse_hw_all();

    oem_bin_file_parse_hw_specific(oem_tool.buf.buf, 0x2);

    fclose(fp);
}