/****************************************************************************

Copyright(c) 2019 by Aerospace C.Power (Chongqing) Microelectronics. ALL RIGHTS RESERVED.

This Information is proprietary to Aerospace C.Power (Chongqing) Microelectronics and MAY NOT
be copied by any method or incorporated into another program without
the express written consent of Aerospace C.Power. This Information or any portion
thereof remains the property of Aerospace C.Power. The Information contained herein
is believed to be accurate and Aerospace C.Power assumes no responsibility or
liability for its use in any way and conveys no license or title under
any patent or copyright and makes no representation or warranty that this
Information is free from patent or copyright infringement.

****************************************************************************/
#include "os_utils.h"
#include "chip_reg_base.h"
#include "hw_reg_api.h"
#include "ahb.h"
#include "gpio_mtx.h"
#include "iot_led.h"
#include "ledc.h"
#include "sec_glb.h"
#include "iot_io.h"
#include "dbg_io.h"

#define REG32(a)        (*((volatile uint32_t *)(a)))

void gpio_sel()
{
    gpio_mtx_enable();
    gpio_sig_info_t sfc = {
        2,
        {
            {IO_TYPE_OUT, 0, 0, 0xff, 52},
            {IO_TYPE_OUT, 0, 1, 0xff, 53},
        }
    };
    gpio_module_pin_select(&sfc);
    gpio_module_sig_select(&sfc, GPIO_MTX_MODE_MATRIX);

    // gpio output inv
    gpio_pin_oinv(1, 1);
    gpio_pin_oinv(0, 0);
}

void led_ctrl_test()
{
    ledc_ena_rst();

    // config timer, timer0 for led0, timer1 for led1, timer2 for reference led
    ledc_timer_cfg(0, 0, 0, 0, 0x10000, 5);
    ledc_timer_cfg(1, 0, 0, 0, 0x10000, 5);
    ledc_timer_cfg(2, 0, 0, 0, 0x10001, 5);

#if 1 // enable reference led clock
    ledc_set_l2h_val(8, 0);
    ledc_target_value(8, 0xa0);
    ledc_target_cfg(8, LED_TARGET_SHADOW_ENA, LED_TARGET_DEC, 8, 1, 2);
    // led config
    ledc_cfg(8, 1, 1, 2);
#endif

#if 1 // enable test led0
    ledc_set_l2h_val(0, 0);
    ledc_target_value(0, 0x100);
    ledc_target_cfg(0, LED_TARGET_SHADOW_ENA, LED_TARGET_DEC, 0, 1, 1);
    ledc_cfg(0, 0, 1, 0);

    // use reference led
//    ledc_out_ref(0, 1);
#endif

#if 1 // enable test led1
    ledc_set_l2h_val(1, 0);
    ledc_target_value(1, 0xa0);
    ledc_target_cfg(1, LED_TARGET_SHADOW_ENA, LED_TARGET_DEC, 0, 1, 1);
    ledc_cfg(1, 0, 1, 1);

    // use reference led
//    ledc_out_ref(1, 1);
#endif

    return;
}

int main(void) {
    dbg_uart_init();
    gpio_sel();
    iot_printf("test led\n");

    led_ctrl_test();

    iot_printf("end.......\n");
    return 0;
}