90 lines
2.8 KiB
C
90 lines
2.8 KiB
C
#include "adc.h"
|
||
|
||
|
||
|
||
static vu8 g_Adc_Inited=0;
|
||
|
||
|
||
//初始化ADC
|
||
void Adc_Init(void)
|
||
{
|
||
GPIO_InitTypeDef GPIO_InitStructure={0};
|
||
ADC_CommonInitTypeDef ADC_CommonInitStructure={0};
|
||
ADC_InitTypeDef ADC_InitStructure={0};
|
||
Adc_DeInit();
|
||
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);//使能GPIOA时钟
|
||
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE); //使能ADC1时钟
|
||
|
||
//先初始化ADC1通道5 IO口
|
||
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;//PA5 通道5
|
||
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;//模拟输入
|
||
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;//不带上下拉
|
||
GPIO_Init(GPIOA, &GPIO_InitStructure);//初始化
|
||
|
||
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1,ENABLE); //ADC1复位
|
||
RCC_APB2PeriphResetCmd(RCC_APB2Periph_ADC1,DISABLE); //复位结束
|
||
|
||
|
||
ADC_CommonInitStructure.ADC_Mode = ADC_Mode_Independent;//独立模式
|
||
ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;//两个采样阶段之间的延迟5个时钟
|
||
ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled; //DMA失能
|
||
ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div4;//预分频4分频。ADCCLK=PCLK2/4=84/4=21Mhz,ADC时钟最好不要超过36Mhz
|
||
ADC_CommonInit(&ADC_CommonInitStructure);//初始化
|
||
|
||
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;//12位模式
|
||
ADC_InitStructure.ADC_ScanConvMode = DISABLE;//非扫描模式
|
||
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;//关闭连续转换
|
||
ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;//禁止触发检测，使用软件触发
|
||
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;//右对齐
|
||
ADC_InitStructure.ADC_NbrOfConversion = 1;//1个转换在规则序列中 也就是只转换规则序列1
|
||
ADC_Init(ADC1, &ADC_InitStructure);//ADC初始化
|
||
|
||
|
||
ADC_Cmd(ADC1, ENABLE);//开启AD转换器
|
||
g_Adc_Inited=1;
|
||
}
|
||
|
||
|
||
|
||
void Adc_DeInit (void)
|
||
{
|
||
ADC_Cmd(ADC1, DISABLE);
|
||
ADC_DeInit();
|
||
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, DISABLE);
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
//获得ADC值
|
||
//ch: @ref ADC_channels
|
||
//通道值 0~16取值范围为：ADC_Channel_0~ADC_Channel_16
|
||
//返回值:转换结果
|
||
u16 Get_Adc(u8 ch)
|
||
{
|
||
|
||
if (g_Adc_Inited==0) return 0;
|
||
//设置指定ADC的规则组通道，一个序列，采样时间
|
||
ADC_RegularChannelConfig(ADC1, ch, 1, ADC_SampleTime_3Cycles ); //ADC1,ADC通道,480个周期,提高采样时间可以提高精确度
|
||
|
||
ADC_SoftwareStartConv(ADC1); //使能指定的ADC1的软件转换启动功能
|
||
u32 t=10000;
|
||
while((!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC ))&&t--);//等待转换结束
|
||
if (t==(u32)-1)
|
||
{
|
||
//Adc_Init();
|
||
}
|
||
ADC_ClearFlag (ADC1,ADC_FLAG_EOC);
|
||
return ADC_GetConversionValue(ADC1); //返回最近一次ADC1规则组的转换结果
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|