python_tools/web/layui/Checker/JQChecker.js

var JQCheckerTaskInfo = [
  {
    TaskID: 0,
    TaskName: "电源准备",
    TaskBrief:
      "检测前校准检测过程中需要使用的电压，便于检测过程中快速输出电压。电压范围55~270",
    ParamInfo: [
      "预设电压1",
      "预设电压2",
      "预设电压3",
      "预设电压4",
      "预设电压5",
      "预设电压6",
      "预设电压7",
      "预设电压8",
      "预设电压9",
      "预设电压10",
    ],
    ReturnInfo: [],
    CommTestCmd: "PowerPrapare",
    TaskErr:21,
    ReturnErr:[],
  },
  {
    TaskID: 1,
    TaskName: "上电充能",
    TaskBrief: "统计上电瞬间，模块功耗。电流计数方式 A = 3.3*ADC/4096/510/11",
    ParamInfo: ["总线电压", "采样超时0.1ms", "计时启停ADC"],
    ReturnInfo: ["总线电压", "大于启停的时间"],
    CommTestCmd: "PowerOn",
    TaskErr:22,
    ReturnErr:[23,22],
  },
  {
    TaskID: 2,
    TaskName: "设置总线电压",
    TaskBrief: "设置总线电压为预设电压中的值",
    ParamInfo: ["总线电压"],
    ReturnInfo: ["总线电压"],
    CommTestCmd: "SetBusV",
    TaskErr:23,
    ReturnErr:[23],
  },
  {
    TaskID: 3,
    TaskName: "获取总线电流",
    TaskBrief: "获取总线正反两个极性电流",
    ParamInfo: [],
    ReturnInfo: ["总线正电流", "总线反电流"],
    CommTestCmd: "BaseCur",
    TaskErr:27,
    ReturnErr:[27,27],
  },
  {
    TaskID: 4,
    TaskName: "扫描UID",
    TaskBrief: "芯片通信测试，分配网络地址。芯片复位后，第一条通信测试命令",
    ParamInfo: ["使1/失0反码采集", "使0/失1UID全0验证"],
    ReturnInfo: [
      "最大反馈电流",
      "最大反馈时间",
      "最小反馈电流",
      "最小反馈时间",
      "1字节",
      "3字节",
      "5字节",
      "7字节",
    ],
    CommTestCmd: "ScanUID",
    TaskErr:24,
    ReturnErr:[43,44,43,44,0,0,0,0],
  },
  {
    TaskID: 5,
    TaskName: "密码验证",
    TaskBrief: "芯片密码验证",
    ParamInfo: ["0码/1原码验证"],
    ReturnInfo: [],
    CommTestCmd: "PWCheck",
    TaskErr:29,
    ReturnErr:[],
  },
  {
    TaskID: 6,
    TaskName: "读取芯片代码",
    TaskBrief: "读取芯片代码",
    ParamInfo: [],
    ReturnInfo: ["2字节代码"],
    CommTestCmd: "ReadChipID",
    TaskErr:28,
    ReturnErr:[0],
  },
  {
    TaskID: 7,
    TaskName: "OTP检测",
    TaskBrief: "对OTP数据进行检测,可屏蔽检测区域",
    ParamInfo: [
      "1关/0检UID密码为0",
      "1关/0检延时保留区为0",
      "1关/0检用户区为0",
    ],
    ReturnInfo: [],
    CommTestCmd: "OTPCheck",
    TaskErr:25,
    ReturnErr:[25,25,25],
  },
  {
    TaskID: 8,
    TaskName: "工厂程测检测",
    TaskBrief: "芯片出厂检测，会在24 25区写0xFF",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "FTCheck",
    TaskErr:38,
    ReturnErr:[38],
  },
  {
    TaskID: 9,
    TaskName: "读芯片状态",
    TaskBrief: "将芯片状态值与参数值进行算术与操作，等于参数值表示执行成功",
    ParamInfo: ["状态值掩码"],
    ReturnInfo: ["状态码"],
    CommTestCmd: "ReadState",
    TaskErr:42,
    ReturnErr:[42],
  },
  {
    TaskID: 10,
    TaskName: "写工厂信息",
    TaskBrief: "在OTP 20~23区间写入工厂数据",
    ParamInfo: ["2字节数据", "2字节数据"],
    ReturnInfo: [],
    CommTestCmd: "WriteUserInfo",
    TaskErr:40,
    ReturnErr:[],
  },
  {
    TaskID: 11,
    TaskName: "充能统计",
    TaskBrief:
      "充能统会发送充电命令，计电流判线设定值，从上升到下降的时间。\
同时记录充过程中最大电流。以及结束高压充电的总线电流和充电电流监控时间。\
充电电流判线计数公式 电流=AD/4093*3.3/100/11",
    ParamInfo: [
      "超时0.1us",
      "电流判线AD",
      "充电结束值0.1uA",
      "充电超时0.1S",
      "电流监控0.1S",
    ],
    ReturnInfo: [
      "充能值0.1ms",
      "充末电流0.1uA",
      "最大充电电流0.1mA",
      "充电抖动ADV",
    ],
    CommTestCmd: "ChgEnergy",
    TaskErr:31,
    ReturnErr:[31,33,32,43],
  },
  {
    TaskID: 12,
    TaskName: "充电电压检测",
    TaskBrief: "由高向低扫描芯片电压检测值,扫描失败返回值为0",
    ParamInfo: ["起始DAC", "结束DAC"],
    ReturnInfo: ["扫描通过的DAC"],
    CommTestCmd: "CheckDAC",
    TaskErr:30,
    ReturnErr:[30],
  },
  {
    TaskID: 13,
    TaskName: "延时等待",
    TaskBrief:
      "延时流程，同时可以启动总线电流监测 设置单位0.1S。波动DAC换算 Vad/4096*3.3/100/11",
    ParamInfo: ["延时时间", "使1/失0电流监控"],
    ReturnInfo: ["电流波动DAC"],
    CommTestCmd: "WaitDelay",
    TaskErr:254,
    ReturnErr:[43],
  },
  {
    TaskID: 14,
    TaskName: "写延时",
    TaskBrief: "向延时寄存器写入数据",
    ParamInfo: ["延时"],
    ReturnInfo: [],
    CommTestCmd: "SetDelay",
    TaskErr:36,
    ReturnErr:[],
  },
  {
    TaskID: 15,
    TaskName: "读延时",
    TaskBrief: "读延时寄存器",
    ParamInfo: [],
    ReturnInfo: ["延时值"],
    CommTestCmd: "ReadDelay",
    TaskErr:37,
    ReturnErr:[37],
  },
  {
    TaskID: 16,
    TaskName: "时钟校准",
    TaskBrief: "发送校准脉冲",
    ParamInfo: ["脉冲周期", "脉冲个数"],
    ReturnInfo: [],
    CommTestCmd: "ClkTrim",
    TaskErr:39,
    ReturnErr:[39],
  },
  {
    TaskID: 17,
    TaskName: "放电",
    TaskBrief:
      "发送放电命令,使能快速放电，还需要配置放电时间。快速放电仅JQ2012才有。放电时间单位0.1S，该值应该大于0快速放电才有效",
    ParamInfo: ["0/1使能快速", "快速时间"],
    ReturnInfo: [],
    CommTestCmd: "Discharge",
    TaskErr:45,
    ReturnErr:[],
  },
  {
    TaskID: 18,
    TaskName: "复位放电",
    TaskBrief: "执行复位和放电，并检测复测成功",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "Reset",
    TaskErr:45,
    ReturnErr:[],
  },
  {
    TaskID: 19,
    TaskName: "起爆使能",
    TaskBrief: "发送起爆使能命令",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "BootEn",
    TaskErr:41,
    ReturnErr:[],
  },
  {
    TaskID: 20,
    TaskName: "起爆充能",
    TaskBrief:
      "发送起爆命令后，检测起爆完成后对电容的充电。判断电流上升沿到下降沿的时间。充能电流ADC/4096*3.3/100/21",
    ParamInfo: ["电流判线AD", "起爆脉冲个数", "延时采集时间"],
    ReturnInfo: ["充能时间", "充电电流", "充电电流波动"],
    CommTestCmd: "BoomEnergy",
    TaskErr:41,
    ReturnErr:[41,41,43],
  },
  {
    TaskID: 21,
    TaskName: "使能通讯末电流采集",
    TaskBrief:
      "启动命令通讯结束后电流采集，与获取通讯电流配合。两个任务间应该避免充电、OTP写和起爆操作",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "EnCommEndCur",
    TaskErr:26,
    ReturnErr:[],
  },
  {
    TaskID: 22,
    TaskName: "获取通讯末电流",
    TaskBrief:
      "获取通讯电流配合与使能通讯末电流采集，获取两个任务间，通讯完成后的最大电流",
    ParamInfo: [],
    ReturnInfo: ["通讯末电流"],
    CommTestCmd: "GetCommEndCur",
    TaskErr:26,
    ReturnErr:[26],
  },
  {
    TaskID: 23,
    TaskName: "写OTP数据",
    TaskBrief: "向芯片OTP中写入数据",
    ParamInfo: ["OTP地址", "数据长度", "1数据", "3数据", "5数据", "7数据"],
    ReturnInfo: [],
    CommTestCmd: "WriteOTP",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 24,
    TaskName: "读OTP数据",
    TaskBrief: "从芯片OTP中读取数据",
    ParamInfo: ["OTP地址", "数据长度"],
    ReturnInfo: ["nBytesOTP数据"],
    CommTestCmd: "ReadOTP",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 25,
    TaskName: "清除起爆命令",
    TaskBrief: "起爆脉冲重新计算",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "ClearBoom",
    TaskErr:41,
    ReturnErr:[],
  },
  {
    TaskID: 26,
    TaskName: "关总线",
    TaskBrief: "关闭总线输出",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "PowerOff",
    TaskErr:254,
    ReturnErr:[],
  },
  {
    TaskID: 27,
    TaskName: "缓存写入OTP",
    TaskBrief: "缓存数据写入OTP数据",
    ParamInfo: ["OTP 地址", "缓存区起始", "写入数据长度"],
    ReturnInfo: [],
    CommTestCmd: "PowerOff",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 28,
    TaskName: "三码绑定",
    TaskBrief: "注码检测指令使用，直接使用命令中的三码数据",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "BindUIDPWD",
    TaskErr:52,
    ReturnErr:[],
  },
  {
    TaskID: 29,
    TaskName: "验证三码",
    TaskBrief: "验证芯片三码数据，直接使用命令中的三码数据",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "VerifyUIDPWD",
    TaskErr:53,
    ReturnErr:[],
  },
  {
    TaskID: 30,
    TaskName: "电容压差",
    TaskBrief: "充电后，总线断电测试电容给芯片供电，评估芯片延时功耗",
    ParamInfo: ["断电时间0.1S"],
    ReturnInfo: ["压差mV"],
    CommTestCmd: "CapVoltage",
    TaskErr:34,
    ReturnErr:[34],
  },
  {
    TaskID: 31,
    TaskName: "桥丝电阻测试",
    TaskBrief: "测量桥丝阻值。可配置测量模式 0 4线制， 1 2线1-4通，2 2线2-3通",
    ParamInfo: ["测量模式"],
    ReturnInfo: ["电阻0.01Ω"],
    CommTestCmd: "ResistorSample",
    TaskErr:51,
    ReturnErr:[51],
  },
  {
    TaskID: 32,
    TaskName: "使能OTP",
    TaskBrief: "OTP使能命令",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "EnOTPW",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 33,
    TaskName: "写版本",
    TaskBrief: "写入模块版本号到OTP 20地址，该值应该小于32",
    ParamInfo: ["版本号"],
    ReturnInfo: [],
    CommTestCmd: "WriteVersion",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 34,
    TaskName: "读版本",
    TaskBrief: "获取写入的版本号",
    ParamInfo: [],
    ReturnInfo: ["版本号"],
    CommTestCmd: "ReadVersion",
    TaskErr:25,
    ReturnErr:[40],
  },
  {
    TaskID: 35,
    TaskName: "写缓存数据",
    TaskBrief: "将系统缓存区的数据写入到OTP中，主要用于写工厂信息",
    ParamInfo: ["OTP地址", "缓存地址", "写入长度"],
    ReturnInfo: [],
    CommTestCmd: "WriteFacBuff",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 36,
    TaskName: "验证缓存数据",
    TaskBrief: "对比缓存数据与OTP数据",
    ParamInfo: ["OTP地址", "缓存地址", "验证长度"],
    ReturnInfo: [],
    CommTestCmd: "VerifyFacBuff",
    TaskErr:25,
    ReturnErr:[],
  },
  {
    TaskID: 37,
    TaskName: "验证延时时间",
    TaskBrief: "验证延时和otp是否相等",
    ParamInfo: [],
    ReturnInfo: [],
    CommTestCmd: "VerifyFacBuff",
    TaskErr:37,
    ReturnErr:[],
  },
  {
    TaskID: 38,
    TaskName: "切换总线极性",
    TaskBrief: "反复切换总线极性，输出最后一次极性切换后的电流",
    ParamInfo: ["间隔时间ms", "切换次数"],
    ReturnInfo: [],
    CommTestCmd: "VerifyFacBuff",
    TaskErr:254,
    ReturnErr:[],
  },
  {
    TaskID: 39,
    TaskName: "异常判定",
    TaskBrief:
      "对已检项目进行异常判定，如果异常判定结果不在过滤范围内，则此任务失败",
    ParamInfo: [
      "过滤值1",
      "过滤值2",
      "过滤值3",
      "过滤值4",
      "过滤值5",
      "过滤值6",
      "过滤值7",
      "过滤值8",
      "过滤值9",
      "过滤值10",
    ],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:0,
    ReturnErr:[],
  },
  {
    TaskID: 40,
    TaskName: "重新执行任务",
    TaskBrief: "重新执行指定序号的任务，本次执行会覆盖之前的结果",
    ParamInfo: ["需要重新执行的任务序号"],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:0,
    ReturnErr:[],
  },
  {
    TaskID: 41,
    TaskName: "配置三码数据到小板",
    TaskBrief: "先把三码数据写入小板缓存，然后才能使用三码绑定任务",
    ParamInfo: [
      "uid,pwd长度",
      "数据0,1",
      "数据2,3",
      "数据4,5",
      "数据6,7",
      "数据8,9",
      "数据10,11",
      "数据12,13",
      "数据14,15",
      "数据16,17",
    ],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:254,
    ReturnErr:[],
  },
  {
    TaskID: 42,
    TaskName: "任务插槽",
    TaskBrief:
      "程序可以动态添加要执行的任务，此任务将执行所有序号匹配的动态任务",
    ParamInfo: ["插槽序号"],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:0,
    ReturnErr:[],
  },
  {
    TaskID: 43,
    TaskName: "设置电阻校准值",
    TaskBrief: "电阻测量的校准值，不建议将此任务添加进方案中",
    ParamInfo: ["电阻校准值"],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:254,
    ReturnErr:[],
  },
  {
    TaskID: 44,
    TaskName: "写入流水号",
    TaskBrief: "采用读改写的方式写入27bit的流水号数据",
    ParamInfo: ["要写入的流水号低2字节", "要写入的流水号高2字节"],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:40,
    ReturnErr:[],
  },
  {
    TaskID: 45,
    TaskName: "读取流水号",
    TaskBrief: "读取27bit的流水号数据，对比失败则此任务失败",
    ParamInfo: ["要校验的流水号低2字节", "要校验的流水号高2字节"],
    ReturnInfo: ["读取的流水号低2字节", "读取的流水号高2字节"],
    CommTestCmd: "ResistorSample",
    TaskErr:40,
    ReturnErr:[],
  },
  {
    TaskID: 46,
    TaskName: "写固定延时",
    TaskBrief: "写入延时并掉电保存",
    ParamInfo: ["延时值ms"],
    ReturnInfo: [],
    CommTestCmd: "ResistorSample",
    TaskErr:40,
    ReturnErr:[],
  },
];
JQ_ErrorInfo = {
  //错误描述
  //主错误段
  MajorErrInfo: [
    {
      Info: "执行成功",
      MajorErrCode: 0,
      SubErrCode: [],
      ErrFac: ["未检测到异常"],
    },
    {
      Info: "检测器异常",
      MajorErrCode: 1,
      SubErrCode: [21, 23, 254],
      ErrFac: ["1.外部短路导致检测器调压失败", "2.设备故障"],
    },
    // 主电容异常移除 dac比较错误30，状态错误42
    // 如果有电容异常，在充能阶段已经暴露
    {
      Info: "主电容异常",
      MajorErrCode: 2,
      SubErrCode: [31, 32, 33, 34, 35],
      ErrFac: ["1.电容充放电测试指标超出限制", "2.电容短路、短路或损坏"],
    },
    {
      Info: "接触异常",
      MajorErrCode: 3,
      SubErrCode: [27],
      ErrFac: ["1.线路接触异常", "2.模块铆接异常", "3.芯片虚焊或损坏"],
    },
    // 桥丝异常移除 41，42
    // 如果有桥丝异常，在dac比较阶段和电阻检阶段已暴露
    {
      Info: "桥丝阻值异常",
      MajorErrCode: 4,
      SubErrCode: [30, 51],
      ErrFac: ["1.(外力导致)桥丝断", "2.桥丝焊接异常"],
    },
    // 移除上电充能异常22，加入其他异常
    {
      Info: "芯片异常",
      MajorErrCode: 5,
      SubErrCode: [
        24, 25, 26, 27, 28, 29, 30, 32, 33, 35, 36, 37, 38, 39, 40, 41, 42, 43,
        44, 45, 52, 53, 54,
      ],
      ErrFac: ["1.对芯片功能(读写OTP、时钟校准等)的检测失败"],
    },
    {
      Info: "判定任务缺失",
      MajorErrCode: 6,
      SubErrCode: [212],
      ErrFac: ["1.设备程序未更新"],
    },
    {
      Info: "过流",
      MajorErrCode: 7,
      SubErrCode: [],
      ErrFac: ["1.模块静态电流指标超过限制"],
    },
    {
      Info: "连接线短路",
      MajorErrCode: 8,
      SubErrCode: [],
      ErrFac: ["1.线路短路", "2.芯片焊接异常", "3.器件损坏"],
    },
    {
      Info: "未执行槽任务",
      MajorErrCode: 9,
      SubErrCode: [],
      ErrFac: ["1.设备程序未更新"],
    },
    {
      Info: "槽任务参数错误",
      MajorErrCode: 10,
      SubErrCode: [],
      ErrFac: ["1.槽任务(写延时、写流水号等)返回值错误"],
    },
    {
      Info: "其他异常",
      MajorErrCode: 20,
      SubErrCode: [22, 255, 208, 209, 210, 211, 212, 213],
      ErrFac: ["1.不常见的异常"],
    },
  ], //需要根据返回参数进行判断]
  SubErrInfo: [
    //详细错误段
    {
      Info: "无异常",
      ErrCode: 0,
      ErrFac: ["1.当检测任务不产生异常时使用此错误码"],
    },
    {
      Info: "预设电压异常",
      ErrCode: 21,
      ErrFac: ["1.检测小板电压调节失效，存在无法设置的电压"],
    },
    {
      Info: "上电充能错误",
      ErrCode: 22,
      ErrFac: [
        "1.检测器输出电压异常",
        "2.模块上电容性负载大",
        "3.模块基本电路异常",
      ],
    },
    {
      Info: "电压设置异常",
      ErrCode: 23,
      ErrFac: ["1.检测小板输出电压异常", "2.外部短路，导致过流保护"],
    },
    {
      Info: "UID扫描错误",
      ErrCode: 24,
      ErrFac: ["1.芯片通信异常", "2.OTP中UID非0(启用了UID全0检测)"],
    },
    { Info: "OTP错误", ErrCode: 25, ErrFac: ["1.OTP数据非全0(启用了全0检测)"] },
    { Info: "通讯电流错误", ErrCode: 26, ErrFac: ["1.芯片反码电流异常"] },
    {
      Info: "基本电流错误",
      ErrCode: 27,
      ErrFac: ["1.芯片的静态功耗异常", "2.检测器输出电压异常"],
    },
    { Info: "读取芯片ID错误", ErrCode: 28, ErrFac: ["1.通信错误"] },
    {
      Info: "密码验证错误",
      ErrCode: 29,
      ErrFac: ["1.芯片异常，内部密码与严重密码不一致"],
    },
    {
      Info: "DAC比较错误",
      ErrCode: 30,
      ErrFac: [
        "1.芯片异常，检测DAC不准",
        "2.电容端电压异常，不符合检测要求",
        "3.高压或充电降压通信异常",
        "4.芯片充电漏流偏大",
      ],
    },
    {
      Info: "高压充能错误",
      ErrCode: 31,
      ErrFac: [
        "1.电容漏流",
        "2.电容容值偏低或偏大",
        "3.芯片充电漏流,充电回路或起爆回路",
        "4.芯片高压基本电流偏大",
        "5.芯片异常，充电电流偏小",
      ],
    },
    {
      Info: "充电电流错误",
      ErrCode: 32,
      ErrFac: ["1.芯片异常，充电电流符合指标"],
    },
    {
      Info: "高压充末电流错误",
      ErrCode: 33,
      ErrFac: [
        "1.电容漏流",
        "2.芯片充电回路漏流或起爆回路漏流",
        "3.芯片高压基本电流偏大",
      ],
    },
    {
      Info: "低压充电能量错误",
      ErrCode: 34,
      ErrFac: [
        "1.电容漏流",
        "2.电容容值偏低或偏大",
        "3.芯片充电漏流,充电回路或起爆回路",
        "4.芯片低压基本电流偏大",
        "5.芯片异常，充电电流偏小",
        "6.高压充电后不能放电",
      ],
    },
    {
      Info: "低压充末电流错误",
      ErrCode: 35,
      ErrFac: [
        "1.电容漏流",
        "2.芯片充电回路漏流或起爆回路漏流",
        "3.芯片基本功耗偏大",
      ],
    },
    {
      Info: "写延时错误",
      ErrCode: 36,
      ErrFac: ["1.芯片设置延时功能异常", "2.通信异常"],
    },
    {
      Info: "读延时错误",
      ErrCode: 37,
      ErrFac: ["1.芯片读延时功能异常", "2.通信异常"],
    },
    {
      Info: "芯片程测错误",
      ErrCode: 38,
      ErrFac: ["1.芯片成测标记错误，非全FFFF", "2.通信异常"],
    },
    { Info: "时钟校准错误", ErrCode: 39, ErrFac: ["1.检测器命令执行异常"] },
    {
      Info: "写工厂信息错误",
      ErrCode: 40,
      ErrFac: ["1.OTP数据写入出错", "2.通信异常"],
    },
    { Info: "模拟起爆错误", ErrCode: 41, ErrFac: ["1.发送起爆指令后无应答"] },
    {
      Info: "芯片状态码异常",
      ErrCode: 42,
      ErrFac: ["1.状态码与设置的掩码不匹配", "2.通讯异常"],
    },
    {
      Info: "通信电流错误",
      ErrCode: 43,
      ErrFac: ["1.芯片异常", "2.检测器异常"],
    },
    {
      Info: "反码时长错误",
      ErrCode: 44,
      ErrFac: ["1.芯片异常，通讯无反码", "2.通讯反码电流低，不能识别"],
    },
    {
      Info: "复位放电错误",
      ErrCode: 45,
      ErrFac: [
        "1.高压充电后降压通讯异常",
        "2.芯片复位不能正常放电",
        "3.芯片异常，指令不执行",
      ],
    },
    {
      Info: "桥丝阻值异常",
      ErrCode: 51,
      ErrFac: ["1.桥丝电阻不符合标准", "2.测试设备校准偏差"],
    },
    {
      Info: "三码绑定失败",
      ErrCode: 52,
      ErrFac: ["1.模块已注过码", "2.芯片异常，无法注码"],
    },
    {
      Info: "三码验证失败",
      ErrCode: 53,
      ErrFac: ["1.芯片异常，注码后验证失败"],
    },
    {
      Info: "缓存信息写入失败",
      ErrCode: 54,
      ErrFac: ["1.系统内部缓存数据异常", "2.芯片数据写入异常"],
    },
    {
      Info: "通信超时",
      ErrCode: 208,
      ErrFac: ["1.小板状态异常，不响应通信指令", "2.小板与主板之间通信异常"],
    },
    {
      Info: "脚本执行失败",
      ErrCode: 209,
      ErrFac: ["1.脚本功能异常", "2.配置文件配置为不使用脚本"],
    },
    {
      Info: "数据长度与方案不符",
      ErrCode: 210,
      ErrFac: ["1.小板和主板使用的方案不同，更新方案即可", "2.脚本功能异常"],
    },
    {
      Info: "方案ID不符",
      ErrCode: 211,
      ErrFac: [
        "1.使用的方案和脚本适配的方案不适配，更换相应的脚本或者方案即可",
      ],
    },
    {
      Info: "检测项目不足",
      ErrCode: 212,
      ErrFac: [
        "1.方案中未执行异常判定所需的任务，无法判定异常",
        "2.脚本功能异常",
      ],
    },
    {
      Info: "数据不合规",
      ErrCode: 213,
      ErrFac: [
        "1.用于判定的数据不具有正常的电性能检测规律，模块检测时不应出现此错误",
        "2.脚本功能异常",
        "3.方案中相关异常判定参数设置不合理",
        "4.小板和主板使用的方案不同但数据返回长度相同，导致错误解释了返回数据的含义",
      ],
    },

    { Info: "检测器执行异常", ErrCode: 254, ErrFac: ["广播类命令执行错误"] },
    { Info: "返回参数判断", ErrCode: 255, ErrFac: [] }, //需要通过指标判断
  ],
};
var JQ_Product_Names = ["EJ", "EQ", "EJ(Q)", "MQ"];