550 lines
18 KiB
JavaScript
550 lines
18 KiB
JavaScript
var JQCheckerTaskInfo=[
|
||
{
|
||
TaskID: 0,
|
||
TaskName: "电源准备",
|
||
TaskBrief: "检测前校准检测过程中需要使用的电压，便于检测过程中快速输出电压。电压范围55~270",
|
||
ParamInfo: ["预设电压1", "预设电压2", "预设电压3", "预设电压4", "预设电压5", "预设电压6", "预设电压7", "预设电压8", "预设电压9", "预设电压10",],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "PowerPrapare",
|
||
}, {
|
||
TaskID: 1,
|
||
TaskName: "上电充能",
|
||
TaskBrief: "统计上电瞬间，模块功耗。电流计数方式 A = 3.3*ADC/4096/510/11",
|
||
ParamInfo: ["总线电压", "采样超时0.1ms", "计时启停ADC"],
|
||
ReturnInfo: ["总线电压", "大于启停的时间"],
|
||
CommTestCmd: "PowerOn",
|
||
}, {
|
||
TaskID: 2,
|
||
TaskName: "设置总线电压",
|
||
TaskBrief: "设置总线电压为预设电压中的值",
|
||
ParamInfo: ["总线电压"],
|
||
ReturnInfo: ["总线电压"],
|
||
CommTestCmd: "SetBusV",
|
||
}, {
|
||
TaskID: 3,
|
||
TaskName: "获取总线电流",
|
||
TaskBrief: "获取总线正反两个极性电流",
|
||
ParamInfo: [],
|
||
ReturnInfo: ["总线正电流", "总线反电流"],
|
||
CommTestCmd: "BaseCur",
|
||
}, {
|
||
TaskID: 4,
|
||
TaskName: "扫描UID",
|
||
TaskBrief: "芯片通信测试，分配网络地址。芯片复位后，第一条通信测试命令",
|
||
ParamInfo: ["使1/失0反码采集", "使0/失1UID全0验证"],
|
||
ReturnInfo: ["最大反馈电流", "最大反馈时间", "最小反馈电流", "最小反馈时间", "1字节", "3字节", "5字节", "7字节"],
|
||
CommTestCmd: "ScanUID",
|
||
}, {
|
||
TaskID: 5,
|
||
TaskName: "密码验证",
|
||
TaskBrief: "芯片密码验证",
|
||
ParamInfo: ["0码/1原码验证"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "PWCheck",
|
||
}, {
|
||
TaskID: 6,
|
||
TaskName: "读取芯片代码",
|
||
TaskBrief: "读取芯片代码",
|
||
ParamInfo: [],
|
||
ReturnInfo: ["2字节代码"],
|
||
CommTestCmd: "ReadChipID",
|
||
}, {
|
||
TaskID: 7,
|
||
TaskName: "OTP检测",
|
||
TaskBrief: "对OTP数据进行检测,可屏蔽检测区域",
|
||
ParamInfo: ["1关/0检UID密码为0", "1关/0检延时保留区为0", "1关/0检用户区为0"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "OTPCheck",
|
||
}, {
|
||
TaskID: 8,
|
||
TaskName: "工厂程测检测",
|
||
TaskBrief: "芯片出厂检测，会在24 25区写0xFF",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "FTCheck",
|
||
}, {
|
||
TaskID: 9,
|
||
TaskName: "读芯片状态",
|
||
TaskBrief: "将芯片状态值与参数值进行算术与操作，等于参数值表示执行成功",
|
||
ParamInfo: ["状态值掩码"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ReadState",
|
||
}, {
|
||
TaskID: 10,
|
||
TaskName: "写工厂信息",
|
||
TaskBrief: "在OTP 20~23区间写入工厂数据",
|
||
ParamInfo: ["2字节数据", "2字节数据"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "WriteUserInfo",
|
||
}, {
|
||
TaskID: 11,
|
||
TaskName: "充能统计",
|
||
TaskBrief: "充能统会发送充电命令，计电流判线设定值，从上升到下降的时间。\
|
||
同时记录充过程中最大电流。以及结束高压充电的总线电流和充电电流监控时间。\
|
||
充电电流判线计数公式 电流=AD/4093*3.3/100/11",
|
||
ParamInfo: ["超时0.1us", "电流判线AD", "充电结束值0.1uA", "充电超时0.1S", "电流监控0.1S"],
|
||
ReturnInfo: ["充能值0.1ms", "充末电流0.1uA", "最大充电电流0.1mA", "充电抖动ADV"],
|
||
CommTestCmd: "ChgEnergy",
|
||
}, {
|
||
TaskID: 12,
|
||
TaskName: "充电电压检测",
|
||
TaskBrief: "由高向低扫描芯片电压检测值,扫描失败返回值为0",
|
||
ParamInfo: ["起始DAC", "结束DAC"],
|
||
ReturnInfo: ["扫描通过的DAC"],
|
||
CommTestCmd: "CheckDAC",
|
||
}, {
|
||
TaskID: 13,
|
||
TaskName: "延时等待",
|
||
TaskBrief: "延时流程，同时可以启动总线电流监测 设置单位0.1S。波动DAC换算 Vad/4096*3.3/100/11",
|
||
ParamInfo: ["延时时间", "使1/失0电流监控"],
|
||
ReturnInfo: ["电流波动DAC"],
|
||
CommTestCmd: "WaitDelay",
|
||
}, {
|
||
TaskID: 14,
|
||
TaskName: "写延时",
|
||
TaskBrief: "向延时寄存器写入数据",
|
||
ParamInfo: ["延时"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "SetDelay",
|
||
}, {
|
||
TaskID: 15,
|
||
TaskName: "读延时",
|
||
TaskBrief: "读延时寄存器",
|
||
ParamInfo: [],
|
||
ReturnInfo: ["延时值"],
|
||
CommTestCmd: "ReadDelay",
|
||
}, {
|
||
TaskID: 16,
|
||
TaskName: "时钟校准",
|
||
TaskBrief: "发送校准脉冲",
|
||
ParamInfo: ["脉冲周期", "脉冲个数"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ClkTrim",
|
||
}, {
|
||
TaskID: 17,
|
||
TaskName: "放电",
|
||
TaskBrief: "发送放电命令,使能快速放电，还需要配置放电时间。快速放电仅JQ2012才有。放电时间单位0.1S，该值应该大于0快速放电才有效",
|
||
ParamInfo: ["0/1使能快速", "快速时间"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "Discharge",
|
||
}, {
|
||
TaskID: 18,
|
||
TaskName: "复位放电",
|
||
TaskBrief: "执行复位和放电，并检测复测成功",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "Reset",
|
||
}, {
|
||
TaskID: 19,
|
||
TaskName: "起爆使能",
|
||
TaskBrief: "发送起爆使能命令",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "BootEn",
|
||
}, {
|
||
TaskID: 20,
|
||
TaskName: "起爆充能",
|
||
TaskBrief: "发送起爆命令后，检测起爆完成后对电容的充电。判断电流上升沿到下降沿的时间。充能电流ADC/4096*3.3/100/21",
|
||
ParamInfo: ["电流判线AD", "起爆脉冲个数", "延时采集时间"],
|
||
ReturnInfo: ["充能时间", "充电电流", "充电电流波动"],
|
||
CommTestCmd: "BoomEnergy",
|
||
}, {
|
||
TaskID: 21,
|
||
TaskName: "使能通讯末电流采集",
|
||
TaskBrief: "启动命令通讯结束后电流采集，与获取通讯电流配合。两个任务间应该避免充电、OTP写和起爆操作",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "EnCommEndCur",
|
||
}, {
|
||
TaskID: 22,
|
||
TaskName: "获取通讯末电流",
|
||
TaskBrief: "获取通讯电流配合与使能通讯末电流采集，获取两个任务间，通讯完成后的最大电流",
|
||
ParamInfo: [],
|
||
ReturnInfo: ["通讯末电流"],
|
||
CommTestCmd: "GetCommEndCur",
|
||
}, {
|
||
TaskID: 23,
|
||
TaskName: "写OTP数据",
|
||
TaskBrief: "向芯片OTP中写入数据",
|
||
ParamInfo: ["OTP地址", "数据长度", "1数据", "3数据", "5数据", "7数据"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "WriteOTP",
|
||
}, {
|
||
TaskID: 24,
|
||
TaskName: "读OTP数据",
|
||
TaskBrief: "从芯片OTP中读取数据",
|
||
ParamInfo: ["OTP地址", "数据长度"],
|
||
ReturnInfo: ["nBytesOTP数据"],
|
||
CommTestCmd: "ReadOTP",
|
||
}, {
|
||
TaskID: 25,
|
||
TaskName: "清除起爆命令",
|
||
TaskBrief: "起爆脉冲重新计算",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ClearBoom",
|
||
}, {
|
||
TaskID: 26,
|
||
TaskName: "关总线",
|
||
TaskBrief: "关闭总线输出",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "PowerOff",
|
||
}, {
|
||
TaskID: 27,
|
||
TaskName: "缓存写入OTP",
|
||
TaskBrief: "缓存数据写入OTP数据",
|
||
ParamInfo: ["OTP 地址", "缓存区起始", "写入数据长度"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "PowerOff",
|
||
},
|
||
{
|
||
TaskID: 28,
|
||
TaskName: "三码绑定",
|
||
TaskBrief: "注码检测指令使用，直接使用命令中的三码数据",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "BindUIDPWD",
|
||
}, {
|
||
TaskID: 29,
|
||
TaskName: "验证三码",
|
||
TaskBrief: "验证芯片三码数据，直接使用命令中的三码数据",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "VerifyUIDPWD",
|
||
}, {
|
||
TaskID: 30,
|
||
TaskName: "电容压差",
|
||
TaskBrief: "充电后，总线断电测试电容给芯片供电，评估芯片延时功耗",
|
||
ParamInfo: ["断电时间0.1S"],
|
||
ReturnInfo: ["压差mV"],
|
||
CommTestCmd: "CapVoltage",
|
||
}, {
|
||
TaskID: 31,
|
||
TaskName: "桥丝电阻测试",
|
||
TaskBrief: "测量桥丝阻值。可配置测量模式 0 4线制， 1 2线1-4通，2 2线2-3通",
|
||
ParamInfo: ["测量模式"],
|
||
ReturnInfo: ["电阻0.01Ω"],
|
||
CommTestCmd: "ResistorSample",
|
||
}, {
|
||
TaskID: 32,
|
||
TaskName: "使能OTP",
|
||
TaskBrief: "OTP使能命令",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "EnOTPW",
|
||
}, {
|
||
TaskID: 33,
|
||
TaskName: "写版本",
|
||
TaskBrief: "写入模块版本号到OTP 20地址，该值应该小于32",
|
||
ParamInfo: ["版本号"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "WriteVersion",
|
||
}, {
|
||
TaskID: 34,
|
||
TaskName: "读版本",
|
||
TaskBrief: "获取写入的版本号",
|
||
ParamInfo: [],
|
||
ReturnInfo: ["版本号"],
|
||
CommTestCmd: "ReadVersion",
|
||
}, {
|
||
TaskID: 35,
|
||
TaskName: "写缓存数据",
|
||
TaskBrief: "将系统缓存区的数据写入到OTP中，主要用于写工厂信息",
|
||
ParamInfo: ["OTP地址", "缓存地址", "写入长度"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "WriteFacBuff",
|
||
}, {
|
||
TaskID: 36,
|
||
TaskName: "验证缓存数据",
|
||
TaskBrief: "对比缓存数据与OTP数据",
|
||
ParamInfo: ["OTP地址", "缓存地址", "验证长度"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "VerifyFacBuff",
|
||
},
|
||
{
|
||
TaskID: 37,
|
||
TaskName: "验证延时时间",
|
||
TaskBrief: "验证延时和otp是否相等",
|
||
ParamInfo: [],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "VerifyFacBuff",
|
||
},
|
||
{
|
||
TaskID: 38,
|
||
TaskName: "切换总线极性",
|
||
TaskBrief: "反复切换总线极性，输出最后一次极性切换后的电流",
|
||
ParamInfo: ["间隔时间ms", "切换次数"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "VerifyFacBuff",
|
||
},
|
||
{
|
||
TaskID: 39,
|
||
TaskName: "异常判定",
|
||
TaskBrief: "对已检项目进行异常判定，如果异常判定结果不在过滤范围内，则此任务失败",
|
||
ParamInfo: ["过滤值1", "过滤值2", "过滤值3", "过滤值4", "过滤值5", "过滤值6", "过滤值7", "过滤值8", "过滤值9", "过滤值10",],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 40,
|
||
TaskName: "重新执行任务",
|
||
TaskBrief: "重新执行指定序号的任务，本次执行会覆盖之前的结果",
|
||
ParamInfo: ["需要重新执行的任务序号"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 41,
|
||
TaskName: "配置三码数据到小板",
|
||
TaskBrief: "先把三码数据写入小板缓存，然后才能使用三码绑定任务",
|
||
ParamInfo: ["uid,pwd长度", "数据0,1", "数据2,3", "数据4,5", "数据6,7", "数据8,9", "数据10,11", "数据12,13", "数据14,15", "数据16,17",],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 42,
|
||
TaskName: "任务插槽",
|
||
TaskBrief: "程序可以动态添加要执行的任务，此任务将执行所有序号匹配的动态任务",
|
||
ParamInfo: ["插槽序号"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 43,
|
||
TaskName: "设置电阻校准值",
|
||
TaskBrief: "电阻测量的校准值，不建议将此任务添加进方案中",
|
||
ParamInfo: ["电阻校准值"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 44,
|
||
TaskName: "写入流水号",
|
||
TaskBrief: "采用读改写的方式写入27bit的流水号数据",
|
||
ParamInfo: ["要写入的流水号低2字节", "要写入的流水号高2字节"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 45,
|
||
TaskName: "读取流水号",
|
||
TaskBrief: "读取27bit的流水号数据，对比失败则此任务失败",
|
||
ParamInfo: ["要校验的流水号低2字节", "要校验的流水号高2字节"],
|
||
ReturnInfo: ["读取的流水号低2字节", "读取的流水号高2字节"],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
{
|
||
TaskID: 46,
|
||
TaskName: "写固定延时",
|
||
TaskBrief: "写入延时并掉电保存",
|
||
ParamInfo: ["延时值ms"],
|
||
ReturnInfo: [],
|
||
CommTestCmd: "ResistorSample",
|
||
},
|
||
|
||
|
||
|
||
];
|
||
JQ_ErrorInfo={
|
||
//错误描述
|
||
//主错误段
|
||
MajorErrInfo:[
|
||
{
|
||
Info:"执行成功",
|
||
MajorErrCode:0,
|
||
SubErrCode:[],
|
||
ErrFac:["未检测到异常"],
|
||
},
|
||
{
|
||
Info:"检测器异常",
|
||
MajorErrCode:1,
|
||
SubErrCode:[21,23,254],
|
||
ErrFac:["1.外部短路导致检测器调压失败","2.设备故障"],
|
||
},
|
||
// 主电容异常移除 dac比较错误30，状态错误42
|
||
// 如果有电容异常，在充能阶段已经暴露
|
||
{
|
||
Info:"主电容异常",
|
||
MajorErrCode:2,
|
||
SubErrCode:[31,32,33,34,35],
|
||
ErrFac:["1.电容充放电测试指标超出限制","2.电容短路、短路或损坏"],
|
||
},
|
||
{
|
||
Info:"接触异常",
|
||
MajorErrCode:3,
|
||
SubErrCode:[27],
|
||
ErrFac:["1.线路接触异常","2.模块铆接异常","3.芯片虚焊或损坏"],
|
||
},
|
||
// 桥丝异常移除 41，42
|
||
// 如果有桥丝异常，在dac比较阶段和电阻检阶段已暴露
|
||
{
|
||
Info:"桥丝阻值异常",
|
||
MajorErrCode:4,
|
||
SubErrCode:[30,51],
|
||
ErrFac:["1.(外力导致)桥丝断","2.桥丝焊接异常"],
|
||
},
|
||
// 移除上电充能异常22，加入其他异常
|
||
{
|
||
Info:"芯片异常",
|
||
MajorErrCode:5,
|
||
SubErrCode:[24,25,26,27,28,29,30,32,33,35,36,37,38,39,40,41,42,43,44,45,52,53,54],
|
||
ErrFac:["1.对芯片功能(读写OTP、时钟校准等)的检测失败"],
|
||
},
|
||
{
|
||
Info:"判定任务缺失",
|
||
MajorErrCode:6,
|
||
SubErrCode:[212],
|
||
ErrFac:["1.设备程序未更新"],
|
||
},
|
||
{
|
||
Info:"过流",
|
||
MajorErrCode:7,
|
||
SubErrCode:[],
|
||
ErrFac:["1.模块静态电流指标超过限制"],
|
||
},
|
||
{
|
||
Info:"连接线短路",
|
||
MajorErrCode:8,
|
||
SubErrCode:[],
|
||
ErrFac:["1.线路短路","2.芯片焊接异常","3.器件损坏"],
|
||
},
|
||
{
|
||
Info:"未执行槽任务",
|
||
MajorErrCode:9,
|
||
SubErrCode:[],
|
||
ErrFac:["1.设备程序未更新"],
|
||
},
|
||
{
|
||
Info:"槽任务参数错误",
|
||
MajorErrCode:10,
|
||
SubErrCode:[],
|
||
ErrFac:["1.槽任务(写延时、写流水号等)返回值错误"],
|
||
},
|
||
{
|
||
Info:"其他异常",
|
||
MajorErrCode:20,
|
||
SubErrCode:[22,255,208,209,210,211,212,213],
|
||
ErrFac:["1.不常见的异常"],
|
||
},
|
||
],//需要根据返回参数进行判断]
|
||
SubErrInfo:[
|
||
//详细错误段
|
||
{Info:"无异常",ErrCode:0,
|
||
ErrFac:["1.当检测任务不产生异常时使用此错误码"]},
|
||
{Info:"预设电压异常",ErrCode:21,
|
||
ErrFac:["1.检测小板电压调节失效，存在无法设置的电压"]},
|
||
{Info:"上电充能错误",ErrCode:22,
|
||
ErrFac:["1.检测器输出电压异常","2.模块上电容性负载大","3.模块基本电路异常"],
|
||
},
|
||
{Info:"电压设置异常",ErrCode:23,
|
||
ErrFac:["1.检测小板输出电压异常","2.外部短路，导致过流保护"]
|
||
},
|
||
{Info:"UID扫描错误",ErrCode:24,
|
||
ErrFac:["1.芯片通信异常","2.OTP中UID非0(启用了UID全0检测)"]},
|
||
{Info:"OTP错误",ErrCode:25,
|
||
ErrFac:["1.OTP数据非全0(启用了全0检测)"]
|
||
},
|
||
{Info:"通讯电流错误",ErrCode:26,
|
||
ErrFac:["1.芯片反码电流异常"]
|
||
},
|
||
{Info:"基本电流错误",ErrCode:27,
|
||
ErrFac:["1.芯片的静态功耗异常","2.检测器输出电压异常"]
|
||
},
|
||
{Info:"读取芯片ID错误",ErrCode:28,
|
||
ErrFac:["1.通信错误"]
|
||
},
|
||
{Info:"密码验证错误",ErrCode:29,
|
||
ErrFac:["1.芯片异常，内部密码与严重密码不一致"]
|
||
},
|
||
{Info:"DAC比较错误",ErrCode:30,
|
||
ErrFac:["1.芯片异常，检测DAC不准","2.电容端电压异常，不符合检测要求","3.高压或充电降压通信异常","4.芯片充电漏流偏大"]
|
||
},
|
||
{Info:"高压充能错误",ErrCode:31,
|
||
ErrFac:["1.电容漏流","2.电容容值偏低或偏大","3.芯片充电漏流,充电回路或起爆回路","4.芯片高压基本电流偏大","5.芯片异常，充电电流偏小"]
|
||
},
|
||
{Info:"充电电流错误",ErrCode:32,
|
||
ErrFac:["1.芯片异常，充电电流符合指标"]
|
||
},
|
||
{Info:"高压充末电流错误",ErrCode:33,
|
||
ErrFac:["1.电容漏流","2.芯片充电回路漏流或起爆回路漏流","3.芯片高压基本电流偏大"],
|
||
},
|
||
{Info:"低压充电能量错误",ErrCode:34,
|
||
ErrFac:["1.电容漏流","2.电容容值偏低或偏大","3.芯片充电漏流,充电回路或起爆回路","4.芯片低压基本电流偏大","5.芯片异常，充电电流偏小","6.高压充电后不能放电"],
|
||
},
|
||
{Info:"低压充末电流错误",ErrCode:35,
|
||
ErrFac:["1.电容漏流","2.芯片充电回路漏流或起爆回路漏流","3.芯片基本功耗偏大"],
|
||
},
|
||
{Info:"写延时错误",ErrCode:36,
|
||
ErrFac:["1.芯片设置延时功能异常","2.通信异常"]
|
||
},
|
||
{Info:"读延时错误",ErrCode:37,
|
||
ErrFac:["1.芯片读延时功能异常","2.通信异常"]
|
||
},
|
||
{Info:"芯片程测错误",ErrCode:38,
|
||
ErrFac:["1.芯片成测标记错误，非全FFFF","2.通信异常"]
|
||
},
|
||
{Info:"时钟校准错误",ErrCode:39,
|
||
ErrFac:["1.检测器命令执行异常"],
|
||
},
|
||
{Info:"写工厂信息错误",ErrCode:40,
|
||
ErrFac:["1.OTP数据写入出错","2.通信异常"]
|
||
},
|
||
{Info:"模拟起爆错误",ErrCode:41,
|
||
ErrFac:["1.发送起爆指令后无应答"]},
|
||
{Info:"芯片状态码异常",ErrCode:42,
|
||
ErrFac:["1.状态码与设置的掩码不匹配","2.通讯异常"]
|
||
},
|
||
{Info:"通信电流错误",ErrCode:43,
|
||
ErrFac:["1.芯片异常","2.检测器异常"],
|
||
},
|
||
{Info:"反码时长错误",ErrCode:44,
|
||
ErrFac:["1.芯片异常，通讯无反码","2.通讯反码电流低，不能识别"]
|
||
},
|
||
{Info:"复位放电错误",ErrCode:45,
|
||
ErrFac:["1.高压充电后降压通讯异常","2.芯片复位不能正常放电","3.芯片异常，指令不执行"],
|
||
},
|
||
{Info:"桥丝阻值异常",ErrCode:51,
|
||
ErrFac:["1.桥丝电阻不符合标准","2.测试设备校准偏差"],
|
||
},
|
||
{Info:"三码绑定失败",ErrCode:52,
|
||
ErrFac:["1.模块已注过码","2.芯片异常，无法注码"],
|
||
},
|
||
{Info:"三码验证失败",ErrCode:53,
|
||
ErrFac:["1.芯片异常，注码后验证失败"],
|
||
},
|
||
{Info:"缓存信息写入失败",ErrCode:54,
|
||
ErrFac:["1.系统内部缓存数据异常","2.芯片数据写入异常"],
|
||
},
|
||
{Info:"通信超时",ErrCode:208,
|
||
ErrFac:["1.小板状态异常，不响应通信指令","2.小板与主板之间通信异常"],
|
||
},
|
||
{Info:"脚本执行失败",ErrCode:209,
|
||
ErrFac:["1.脚本功能异常","2.配置文件配置为不使用脚本"],
|
||
},
|
||
{Info:"数据长度与方案不符",ErrCode:210,
|
||
ErrFac:["1.小板和主板使用的方案不同，更新方案即可","2.脚本功能异常"],
|
||
},
|
||
{Info:"方案ID不符",ErrCode:211,
|
||
ErrFac:["1.使用的方案和脚本适配的方案不适配，更换相应的脚本或者方案即可"],
|
||
},
|
||
{Info:"检测项目不足",ErrCode:212,
|
||
ErrFac:["1.方案中未执行异常判定所需的任务，无法判定异常","2.脚本功能异常"],
|
||
},
|
||
{Info:"数据不合规",ErrCode:213,
|
||
ErrFac:["1.用于判定的数据不具有正常的电性能检测规律，模块检测时不应出现此错误","2.脚本功能异常",
|
||
"3.方案中相关异常判定参数设置不合理","4.小板和主板使用的方案不同但数据返回长度相同，导致错误解释了返回数据的含义"],
|
||
},
|
||
|
||
|
||
|
||
|
||
{Info:"检测器执行异常",ErrCode:254,
|
||
ErrFac:["广播类命令执行错误"],
|
||
},
|
||
{Info:"返回参数判断",ErrCode:255,
|
||
ErrFac:[],
|
||
},//需要通过指标判断
|
||
],
|
||
};
|
||
var JQ_Product_Names=["EJ","EQ","EJ(Q)"]; |