tinyUSB/hw/bsp/mcb1800/board_mcb1800.c

/**************************************************************************/
/*!
 @file    board_mcb1800.c
 @author  hathach (tinyusb.org)

 @section LICENSE

 Software License Agreement (BSD License)

 Copyright (c) 2018, hathach (tinyusb.org)
 All rights reserved.

 Redistribution and use in source and binary forms, with or without
 modification, are permitted provided that the following conditions are met:
 1. Redistributions of source code must retain the above copyright
 notice, this list of conditions and the following disclaimer.
 2. Redistributions in binary form must reproduce the above copyright
 notice, this list of conditions and the following disclaimer in the
 documentation and/or other materials provided with the distribution.
 3. Neither the name of the copyright holders nor the
 names of its contributors may be used to endorse or promote products
 derived from this software without specific prior written permission.

 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
 EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
 DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

 This file is part of the tinyusb stack.
*/
/**************************************************************************/

#ifdef BOARD_MCB1800

#include "../board.h"
#include "tusb.h"

#define LED_PORT  6
#define LED_PIN   24

//--------------------------------------------------------------------+
// MACRO TYPEDEF CONSTANT ENUM DECLARATION
//--------------------------------------------------------------------+
/* System configuration variables used by chip driver */
const uint32_t ExtRateIn = 0;
const uint32_t OscRateIn = 12000000;

static const PINMUX_GRP_T pinmuxing[] =
{
	/* Board LEDs */
	{0xD, 10, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC4)},
	{0xD, 11, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC4)},
	{0xD, 12, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC4)},
	{0xD, 13, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC4)},
	{0xD, 14, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC4)},
	{0x9, 0,  (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC0)},
	{0x9, 1,  (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC0)},
	{0x9, 2,  (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC0)},

	/*  I2S  */
	{0x3, 0,  (SCU_PINIO_FAST | SCU_MODE_FUNC2)},
	{0x6, 0,  (SCU_PINIO_FAST | SCU_MODE_FUNC4)},
	{0x7, 2,  (SCU_PINIO_FAST | SCU_MODE_FUNC2)},
	{0x6, 2,  (SCU_PINIO_FAST | SCU_MODE_FUNC3)},
	{0x7, 1,  (SCU_PINIO_FAST | SCU_MODE_FUNC2)},
	{0x6, 1,  (SCU_PINIO_FAST | SCU_MODE_FUNC3)},
};

/* Pin clock mux values, re-used structure, value in first index is meaningless */
static const PINMUX_GRP_T pinclockmuxing[] =
{
	{0, 0,  (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
	{0, 1,  (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
	{0, 2,  (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
	{0, 3,  (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
};


/*------------------------------------------------------------------*/
/* BOARD API
 *------------------------------------------------------------------*/
// Invoked by startup code
void SystemInit(void)
{
	/* Setup system level pin muxing */
	Chip_SCU_SetPinMuxing(pinmuxing, sizeof(pinmuxing) / sizeof(PINMUX_GRP_T));

	/* Clock pins only, group field not used */
	for (int i = 0; i < (sizeof(pinclockmuxing) / sizeof(pinclockmuxing[0])); i++)
	{
		Chip_SCU_ClockPinMuxSet(pinclockmuxing[i].pinnum, pinclockmuxing[i].modefunc);
	}

  Chip_SetupXtalClocking();
}

void board_init(void)
{
  SystemCoreClockUpdate();

#if CFG_TUSB_OS == OPT_OS_NONE
  SysTick_Config( SystemCoreClock / BOARD_TICKS_HZ );
#endif

  Chip_GPIO_Init(LPC_GPIO_PORT);

  //------------- LED -------------//
  /* Port and bit mapping for LEDs on GPIOs */
  const uint8_t ledports[] = {6, 6, 6, 6, 6, 4, 4, 4};
  const uint8_t ledbits[] = {24, 25, 26, 27, 28, 12, 13, 14};

  for (int i = 0; i < (sizeof(ledports) / sizeof(ledports[0])); i++) 
  {
    Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, ledports[i], ledbits[i]);
    Chip_GPIO_SetPinState(LPC_GPIO_PORT, LED_PORT, LED_PIN, false);
  }

#if 0
  //------------- BUTTON -------------//
  for(uint8_t i=0; i<BOARD_BUTTON_COUNT; i++)
  {
    scu_pinmux(buttons[i].mux_port, buttons[i].mux_pin, GPIO_NOPULL, FUNC0);
    GPIO_SetDir(buttons[i].gpio_port, TU_BIT(buttons[i].gpio_pin), 0);
  }

  //------------- UART -------------//
  scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_TX, MD_PDN, FUNC1);
  scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_RX, MD_PLN | MD_EZI | MD_ZI, FUNC1);

  UART_CFG_Type UARTConfigStruct;
  UART_ConfigStructInit(&UARTConfigStruct);
  UARTConfigStruct.Baud_rate   = CFG_UART_BAUDRATE;
  UARTConfigStruct.Clock_Speed = 0;

  UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
  UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
#endif

  //------------- USB -------------//
  enum {
    USBMODE_DEVICE = 2,
    USBMODE_HOST   = 3
  };

  enum {
    USBMODE_VBUS_LOW  = 0,
    USBMODE_VBUS_HIGH = 1
  };

  // USB0
#if CFG_TUSB_RHPORT0_MODE
  Chip_USB0_Init();

  // Reset controller
  LPC_USB0->USBCMD_D |= 0x02;
  while( LPC_USB0->USBCMD_D & 0x02 ) {}

  // Set mode
  #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST
    LPC_USB0->USBMODE_H = USBMODE_HOST | (USBMODE_VBUS_HIGH << 5);
  #else // TODO OTG
    LPC_USB0->USBMODE_D = USBMODE_DEVICE;
    LPC_USB0->OTGSC = (1<<3) | (1<<0) /*| (1<<16)| (1<<24)| (1<<25)| (1<<26)| (1<<27)| (1<<28)| (1<<29)| (1<<30)*/;
  #endif
#endif

  // USB1
#if CFG_TUSB_RHPORT1_MODE
  Chip_USB1_Init();

  // Reset controller
  LPC_USB1->USBCMD_D |= 0x02;
  while( LPC_USB1->USBCMD_D & 0x02 ) {}

  // Set mode
  #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST
    LPC_USB1->USBMODE_H = USBMODE_HOST | (USBMODE_VBUS_HIGH << 5);
  #else // TODO OTG
    LPC_USB1->USBMODE_D = USBMODE_DEVICE;
  #endif

  // USB1 as fullspeed
  LPC_USB1->PORTSC1_D |= (1<<24);
#endif
}

//------------- LED -------------//
void board_led_control(bool state)
{
  Chip_GPIO_SetPinState(LPC_GPIO_PORT, LED_PORT, LED_PIN, state);
}

//------------- Buttons -------------//
static bool button_read(uint8_t id)
{
//  return !TU_BIT_TEST( GPIO_ReadValue(buttons[id].gpio_port), buttons[id].gpio_pin ); // button is active low
}

uint32_t board_buttons(void)
{
  uint32_t result = 0;

//  for(uint8_t i=0; i<BOARD_BUTTON_COUNT; i++) result |= (button_read(i) ? TU_BIT(i) : 0);

  return result;
}


//------------- UART -------------//
uint8_t  board_uart_getchar(void)
{
  //return UART_ReceiveByte(BOARD_UART_PORT);
}
void board_uart_putchar(uint8_t c)
{
  //UART_Send(BOARD_UART_PORT, &c, 1, BLOCKING);
}

/*------------------------------------------------------------------*/
/* TUSB HAL MILLISECOND
 *------------------------------------------------------------------*/
#if CFG_TUSB_OS == OPT_OS_NONE

volatile uint32_t system_ticks = 0;

void SysTick_Handler (void)
{
  system_ticks++;
}

uint32_t tusb_hal_millis(void)
{
  return board_tick2ms(system_ticks);
}

#endif

#endif