tinyUSB/hw/bsp/ngx4330/board.mk

DEPS_SUBMODULES += hw/mcu/nxp/lpcopen

CFLAGS += \
  -flto \
  -mthumb \
  -mabi=aapcs \
  -mcpu=cortex-m4 \
  -mfloat-abi=hard \
  -mfpu=fpv4-sp-d16 \
  -nostdlib \
  -DCORE_M4 \
  -D__USE_LPCOPEN \
  -DCFG_TUSB_MCU=OPT_MCU_LPC43XX

# mcu driver cause following warnings
CFLAGS += -Wno-error=strict-prototypes -Wno-error=unused-parameter -Wno-error=cast-qual

MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx

# All source paths should be relative to the top level.
LD_FILE = hw/bsp/$(BOARD)/ngx4330.ld

SRC_C += \
	src/portable/chipidea/ci_hs/dcd_ci_hs.c \
	src/portable/chipidea/ci_hs/hcd_ci_hs.c \
	src/portable/ehci/ehci.c \
	$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \
	$(MCU_DIR)/src/chip_18xx_43xx.c \
	$(MCU_DIR)/src/clock_18xx_43xx.c \
	$(MCU_DIR)/src/gpio_18xx_43xx.c \
	$(MCU_DIR)/src/sysinit_18xx_43xx.c \
	$(MCU_DIR)/src/uart_18xx_43xx.c \
	$(MCU_DIR)/src/fpu_init.c

INC += \
	$(TOP)/$(MCU_DIR)/inc \
	$(TOP)/$(MCU_DIR)/inc/config_43xx

# For freeRTOS port source
FREERTOS_PORT = ARM_CM4F

# For flash-jlink target
JLINK_DEVICE = LPC4330
JLINK_IF = swd 

# flash using jlink
flash: flash-jlink
add nxp_lpcopen as submodule 2021-04-28 18:11:49 +07:00			`DEPS_SUBMODULES += hw/mcu/nxp/lpcopen`
merge no-family example build specify FAMILY_SUBMODULES for all boards 2021-03-04 22:50:45 +07:00
adding ngx4330 2019-09-09 16:47:57 +07:00			`CFLAGS += \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-flto \`
adding ngx4330 2019-09-09 16:47:57 +07:00			`-mthumb \`
			`-mabi=aapcs \`
			`-mcpu=cortex-m4 \`
revert to use float-abi define __USE_CMSIS instead of __USE_LPCOPEN will have startup enable FPU on startup properly. Although it is only relevant to lpx43/40 series, change all to __USE_CMSIS for consistency 2020-09-02 00:46:08 +07:00			`-mfloat-abi=hard \`
fix ci build 2020-09-02 00:56:43 +07:00			`-mfpu=fpv4-sp-d16 \`
adding ngx4330 2019-09-09 16:47:57 +07:00			`-nostdlib \`
			`-DCORE_M4 \`
revert to use __USE_LPCOPEN properly init fpu on LPC M4 2020-09-03 12:58:09 +07:00			`-D__USE_LPCOPEN \`
revert to use float-abi define __USE_CMSIS instead of __USE_LPCOPEN will have startup enable FPU on startup properly. Although it is only relevant to lpx43/40 series, change all to __USE_CMSIS for consistency 2020-09-02 00:46:08 +07:00			`-DCFG_TUSB_MCU=OPT_MCU_LPC43XX`
adding ngx4330 2019-09-09 16:47:57 +07:00
add -Wextra for more warnings to example non-stack warning (probably mcu driver) should be suppressed in the board.mk 2019-09-27 00:15:43 +07:00			`# mcu driver cause following warnings`
more -Wcast-qual 2021-10-17 17:32:03 +07:00			`CFLAGS += -Wno-error=strict-prototypes -Wno-error=unused-parameter -Wno-error=cast-qual`
adding ngx4330 2019-09-09 16:47:57 +07:00
update makefile for lpc boards 2019-11-11 11:51:51 +07:00			`MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx`
adding ngx4330 2019-09-09 16:47:57 +07:00
			`# All source paths should be relative to the top level.`
			`LD_FILE = hw/bsp/$(BOARD)/ngx4330.ld`

			`SRC_C += \`
more work to abstract chipidea driver 2021-12-01 23:30:09 +07:00			`src/portable/chipidea/ci_hs/dcd_ci_hs.c \`
			`src/portable/chipidea/ci_hs/hcd_ci_hs.c \`
			`src/portable/ehci/ehci.c \`
adding ngx4330 2019-09-09 16:47:57 +07:00			`$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \`
			`$(MCU_DIR)/src/chip_18xx_43xx.c \`
			`$(MCU_DIR)/src/clock_18xx_43xx.c \`
			`$(MCU_DIR)/src/gpio_18xx_43xx.c \`
			`$(MCU_DIR)/src/sysinit_18xx_43xx.c \`
revert to use __USE_LPCOPEN properly init fpu on LPC M4 2020-09-03 12:58:09 +07:00			`$(MCU_DIR)/src/uart_18xx_43xx.c \`
			`$(MCU_DIR)/src/fpu_init.c`
adding ngx4330 2019-09-09 16:47:57 +07:00
			`INC += \`
			`$(TOP)/$(MCU_DIR)/inc \`
			`$(TOP)/$(MCU_DIR)/inc/config_43xx`

			`# For freeRTOS port source`
freertos demo use static only for most optmized sram 2020-03-11 00:09:37 +07:00			`FREERTOS_PORT = ARM_CM4F`
adding ngx4330 2019-09-09 16:47:57 +07:00
			`# For flash-jlink target`
			`JLINK_DEVICE = LPC4330`
			`JLINK_IF = swd`

			`# flash using jlink`
			`flash: flash-jlink`