tinyUSB/hw/bsp/lpcxpresso55s69/lpcxpresso55s69.c

/* 
 * The MIT License (MIT)
 *
 * Copyright (c) 2018, hathach (tinyusb.org)
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 *
 * This file is part of the TinyUSB stack.
 */

#include "../board.h"
#include "fsl_device_registers.h"
#include "fsl_gpio.h"
#include "fsl_power.h"
#include "fsl_iocon.h"

//--------------------------------------------------------------------+
// Forward USB interrupt events to TinyUSB IRQ Handler
//--------------------------------------------------------------------+
void USB0_IRQHandler(void)
{
  tud_int_handler(0);
}

void USB1_IRQHandler(void)
{
  tud_int_handler(1);
}

//--------------------------------------------------------------------+
// MACRO TYPEDEF CONSTANT ENUM
//--------------------------------------------------------------------+
#define LED_PORT              1
#define LED_PIN               6
#define LED_STATE_ON          0

// WAKE button
#define BUTTON_PORT           1
#define BUTTON_PIN            18
#define BUTTON_STATE_ACTIVE   0

// IOCON pin mux
#define IOCON_PIO_DIGITAL_EN 0x0100u  /*!<@brief Enables digital function */
#define IOCON_PIO_FUNC0 0x00u         /*!<@brief Selects pin function 0 */
#define IOCON_PIO_FUNC1 0x01u         /*!<@brief Selects pin function 1 */
#define IOCON_PIO_FUNC7 0x07u         /*!<@brief Selects pin function 7 */
#define IOCON_PIO_INV_DI 0x00u        /*!<@brief Input function is not inverted */
#define IOCON_PIO_MODE_INACT 0x00u    /*!<@brief No addition pin function */
#define IOCON_PIO_OPENDRAIN_DI 0x00u  /*!<@brief Open drain is disabled */
#define IOCON_PIO_SLEW_STANDARD 0x00u /*!<@brief Standard mode, output slew rate control is enabled */

/****************************************************************
name: BOARD_BootClockFROHF96M
outputs:
- {id: SYSTICK_clock.outFreq, value: 96 MHz}
- {id: System_clock.outFreq, value: 96 MHz}
settings:
- {id: SYSCON.MAINCLKSELA.sel, value: SYSCON.fro_hf}
sources:
- {id: SYSCON.fro_hf.outFreq, value: 96 MHz}
******************************************************************/
void BootClockFROHF96M(void)
{
  /*!< Set up the clock sources */
  /*!< Set up FRO */
  POWER_DisablePD(kPDRUNCFG_PD_FRO192M); /*!< Ensure FRO is on  */
  CLOCK_SetupFROClocking(12000000U);     /*!< Set up FRO to the 12 MHz, just for sure */
  CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch to FRO 12MHz first to ensure we can change voltage without
                                             accidentally being below the voltage for current speed */

  CLOCK_SetupFROClocking(96000000U); /*!< Set up high frequency FRO output to selected frequency */

  POWER_SetVoltageForFreq(96000000U); /*!< Set voltage for the one of the fastest clock outputs: System clock output */
  CLOCK_SetFLASHAccessCyclesForFreq(96000000U); /*!< Set FLASH wait states for core */

  /*!< Set up dividers */
  CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U, false);     /*!< Set AHBCLKDIV divider to value 1 */

  /*!< Set up clock selectors - Attach clocks to the peripheries */
  CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */

  /*!< Set SystemCoreClock variable. */
  SystemCoreClock = 96000000U;
}

void board_init(void)
{
  // Enable IOCON clock
  CLOCK_EnableClock(kCLOCK_Iocon);

  // Init 96 MHz clock
  BootClockFROHF96M();

#if CFG_TUSB_OS == OPT_OS_NONE
  // 1ms tick timer
  SysTick_Config(SystemCoreClock / 1000);
#elif CFG_TUSB_OS == OPT_OS_FREERTOS
  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
  NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
#endif

  GPIO_PortInit(GPIO, LED_PORT);
  GPIO_PortInit(GPIO, BUTTON_PORT);

  // LED
  gpio_pin_config_t const led_config = { kGPIO_DigitalOutput, 0};
  GPIO_PinInit(GPIO, LED_PORT, LED_PIN, &led_config);
  board_led_write(true);

  // Button
  const uint32_t port1_pin18_config = (
      IOCON_PIO_FUNC0         | /* Pin is configured as PIO1_18 */
      IOCON_PIO_MODE_INACT    | /* No addition pin function */
      IOCON_PIO_SLEW_STANDARD | /* Standard mode, output slew rate control is enabled */
      IOCON_PIO_INV_DI        | /* Input function is not inverted */
      IOCON_PIO_DIGITAL_EN    | /* Enables digital function */
      IOCON_PIO_OPENDRAIN_DI    /* Open drain is disabled */
  );
  /* PORT1 PIN18 (coords: 64) is configured as PIO1_18 */
  IOCON_PinMuxSet(IOCON, 1U, 18U, port1_pin18_config);

  gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0};
  GPIO_PinInit(GPIO, BUTTON_PORT, BUTTON_PIN, &button_config);

  // USB VBUS
  const uint32_t port0_pin22_config = (
      IOCON_PIO_FUNC7         | /* Pin is configured as USB0_VBUS */
      IOCON_PIO_MODE_INACT    | /* No addition pin function */
      IOCON_PIO_SLEW_STANDARD | /* Standard mode, output slew rate control is enabled */
      IOCON_PIO_INV_DI        | /* Input function is not inverted */
      IOCON_PIO_DIGITAL_EN    | /* Enables digital function */
      IOCON_PIO_OPENDRAIN_DI    /* Open drain is disabled */
  );
  /* PORT0 PIN22 (coords: 78) is configured as USB0_VBUS */
  IOCON_PinMuxSet(IOCON, 0U, 22U, port0_pin22_config);

  // USB Controller
  POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); /*Turn on USB0 Phy */
  POWER_DisablePD(kPDRUNCFG_PD_USB1_PHY); /*< Turn on USB1 Phy */

  /* reset the IP to make sure it's in reset state. */
  RESET_PeripheralReset(kUSB0D_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB0HSL_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB0HMR_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB1H_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB1D_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB1_RST_SHIFT_RSTn);
  RESET_PeripheralReset(kUSB1RAM_RST_SHIFT_RSTn);

#if (defined USB_DEVICE_CONFIG_LPCIP3511HS) && (USB_DEVICE_CONFIG_LPCIP3511HS)
  CLOCK_EnableClock(kCLOCK_Usbh1);
  /* Put PHY powerdown under software control */
  *((uint32_t *)(USBHSH_BASE + 0x50)) = USBHSH_PORTMODE_SW_PDCOM_MASK;
  /* According to reference mannual, device mode setting has to be set by access usb host register */
  *((uint32_t *)(USBHSH_BASE + 0x50)) |= USBHSH_PORTMODE_DEV_ENABLE_MASK;
  /* enable usb1 host clock */
  CLOCK_DisableClock(kCLOCK_Usbh1);
#endif

#if 1 || (defined USB_DEVICE_CONFIG_LPCIP3511FS) && (USB_DEVICE_CONFIG_LPCIP3511FS)
  CLOCK_SetClkDiv(kCLOCK_DivUsb0Clk, 1, false);
  CLOCK_AttachClk(kFRO_HF_to_USB0_CLK);
  /* enable usb0 host clock */
  CLOCK_EnableClock(kCLOCK_Usbhsl0);
  /*According to reference mannual, device mode setting has to be set by access usb host register */
  *((uint32_t *)(USBFSH_BASE + 0x5C)) |= USBFSH_PORTMODE_DEV_ENABLE_MASK;
  /* disable usb0 host clock */
  CLOCK_DisableClock(kCLOCK_Usbhsl0);
  CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbfsSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); /* enable USB Device clock */
#endif
}

//--------------------------------------------------------------------+
// Board porting API
//--------------------------------------------------------------------+

void board_led_write(bool state)
{
  GPIO_PinWrite(GPIO, LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
}

uint32_t board_button_read(void)
{
  // active low
  return BUTTON_STATE_ACTIVE == GPIO_PinRead(GPIO, BUTTON_PORT, BUTTON_PIN);
}

int board_uart_read(uint8_t* buf, int len)
{
  (void) buf; (void) len;
  return 0;
}

int board_uart_write(void const * buf, int len)
{
  (void) buf; (void) len;
  return 0;
}

#if CFG_TUSB_OS == OPT_OS_NONE
volatile uint32_t system_ticks = 0;
void SysTick_Handler(void)
{
  system_ticks++;
}

uint32_t board_millis(void)
{
  return system_ticks;
}
#endif