tinyUSB/hw/bsp/stm32f7/boards/stm32f723disco/board.h

/*
 * The MIT License (MIT)
 *
 * Copyright (c) 2021, Ha Thach (tinyusb.org)
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 *
 * This file is part of the TinyUSB stack.
 */

#ifndef BOARD_H_
#define BOARD_H_

#ifdef __cplusplus
 extern "C" {
#endif

#define LED_PORT              GPIOB
#define LED_PIN               GPIO_PIN_1
#define LED_STATE_ON          1

#define BUTTON_PORT           GPIOA
#define BUTTON_PIN            GPIO_PIN_0
#define BUTTON_STATE_ACTIVE   1

#define UART_DEV              USART6
#define UART_CLK_EN           __HAL_RCC_USART6_CLK_ENABLE
#define UART_GPIO_AF          GPIO_AF8_USART6

#define UART_TX_PORT          GPIOC
#define UART_TX_PIN           GPIO_PIN_6

#define UART_RX_PORT          GPIOC
#define UART_RX_PIN           GPIO_PIN_7

// VBUS Sense detection
#define OTG_FS_VBUS_SENSE     1
#define OTG_HS_VBUS_SENSE     0

//--------------------------------------------------------------------+
// RCC Clock
//--------------------------------------------------------------------+
static inline void board_clock_init(void) {
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;

  /* Enable Power Control clock */
  __HAL_RCC_PWR_CLK_ENABLE();

  /* The voltage scaling allows optimizing the power consumption when the device is
     clocked below the maximum system frequency, to update the voltage scaling value
     regarding system frequency refer to product datasheet.  */
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  /* Enable HSE Oscillator and activate PLL with HSE as source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = HSE_VALUE / 1000000;
  RCC_OscInitStruct.PLL.PLLN = 432;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 9;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  /* Activate the OverDrive to reach the 216 MHz Frequency */
  HAL_PWREx_EnableOverDrive();

  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;

  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
}

//static inline void board_vbus_sense_init(void)
//{
//
//}

typedef struct {
  GPIO_TypeDef* port;
  GPIO_InitTypeDef pin_init;
  bool active_state;
} board_pindef_t;

static board_pindef_t vbus_pindef[] = {
{
    .port = GPIOG,
    .pin_init = {
      .Pin = GPIO_PIN_8, .Mode = GPIO_MODE_OUTPUT_OD, .Pull = GPIO_NOPULL,
      .Speed = GPIO_SPEED_HIGH, .Alternate = 0
    },
    .active_state = false
  },
{
    .port = GPIOH,
    .pin_init = {
      .Pin = GPIO_PIN_12, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_NOPULL,
      .Speed = GPIO_SPEED_HIGH, .Alternate = 0
    },
    .active_state = true
  },
};

static inline void board_vbus_set(uint8_t rhport, bool state) {
  static bool pin_inited[2] = { false, false };
  board_pindef_t* pindef = &vbus_pindef[rhport];
  if (!pin_inited[rhport]) {
    HAL_GPIO_Init(pindef->port, &pindef->pin_init);
    pin_inited[rhport] = true;
  }

  HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
}

#ifdef __cplusplus
 }
#endif

#endif /* BOARD_H_ */