2019-03-22 22:06:48 +07:00
|
|
|
CFLAGS += \
|
|
|
|
|
-DHSE_VALUE=8000000 \
|
|
|
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32F3 \
|
|
|
|
|
-DSTM32F303xC \
|
|
|
|
|
-mthumb \
|
|
|
|
|
-mabi=aapcs-linux \
|
|
|
|
|
-mcpu=cortex-m4 \
|
|
|
|
|
-mfloat-abi=hard \
|
|
|
|
|
-mfpu=fpv4-sp-d16 \
|
|
|
|
|
-nostdlib -nostartfiles
|
|
|
|
|
|
|
|
|
|
# All source paths should be relative to the top level.
|
|
|
|
|
LD_FILE = hw/bsp/stm32f303disc/STM32F303VCTx_FLASH.ld
|
|
|
|
|
|
|
|
|
|
LDFLAGS += -mthumb -mcpu=cortex-m4
|
|
|
|
|
|
|
|
|
|
SRC_C += \
|
2019-03-22 23:57:14 +07:00
|
|
|
hw/mcu/st/system-init/system_stm32f3xx.c \
|
|
|
|
|
hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Src/stm32f3xx_hal.c \
|
|
|
|
|
hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Src/stm32f3xx_hal_cortex.c \
|
|
|
|
|
hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Src/stm32f3xx_hal_rcc.c \
|
|
|
|
|
hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Src/stm32f3xx_hal_gpio.c
|
2019-03-22 22:06:48 +07:00
|
|
|
|
|
|
|
|
SRC_S += \
|
|
|
|
|
hw/mcu/st/startup/stm32f3/startup_stm32f303xc.s
|
|
|
|
|
|
|
|
|
|
INC += \
|
2019-05-01 14:27:17 +07:00
|
|
|
$(TOP)/hw/bsp/stm32f303disc \
|
|
|
|
|
$(TOP)/hw/mcu/st/cmsis \
|
|
|
|
|
$(TOP)/hw/mcu/st/stm32lib/CMSIS/STM32F3xx/Include \
|
|
|
|
|
$(TOP)/hw/mcu/st/stm32lib/STM32F3xx_HAL_Driver/Inc
|
2019-03-22 22:06:48 +07:00
|
|
|
|
2019-05-01 14:27:17 +07:00
|
|
|
# For TinyUSB port source
|
2019-03-22 22:06:48 +07:00
|
|
|
VENDOR = st
|
2019-03-22 23:57:14 +07:00
|
|
|
CHIP_FAMILY = stm32f3
|
2019-03-22 22:06:48 +07:00
|
|
|
|
2019-05-01 14:27:17 +07:00
|
|
|
# For freeRTOS port source
|
|
|
|
|
FREERTOS_PORT = ARM_CM4F
|
|
|
|
|
|
|
|
|
|
# For flash-jlink target
|
2019-03-22 22:06:48 +07:00
|
|
|
JLINK_DEVICE = stm32f303vc
|
2019-05-01 14:27:17 +07:00
|
|
|
JLINK_IF = swd
|
2019-03-22 22:06:48 +07:00
|
|
|
|
|
|
|
|
# Path to STM32 Cube Programmer CLI, should be added into system path
|
|
|
|
|
STM32Prog = STM32_Programmer_CLI
|
|
|
|
|
|
|
|
|
|
# flash target using on-board stlink
|
|
|
|
|
flash: $(BUILD)/$(BOARD)-firmware.elf
|
|
|
|
|
$(STM32Prog) --connect port=swd --write $< --go
|
