52 lines
1.3 KiB
Makefile
52 lines
1.3 KiB
Makefile
|
CFLAGS += \
|
||
|
|
-DHSE_VALUE=8000000 \
|
||
|
|
-DSTM32F412Zx \
|
||
|
|
-mthumb \
|
||
|
|
-mabi=aapcs \
|
||
|
|
-mcpu=cortex-m4 \
|
||
|
|
-mfloat-abi=hard \
|
||
|
|
-mfpu=fpv4-sp-d16 \
|
||
|
|
-nostdlib -nostartfiles \
|
||
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32F4
|
||
|
|
|
||
|
|
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver
|
||
|
|
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx
|
||
|
|
|
||
|
|
# All source paths should be relative to the top level.
|
||
|
|
LD_FILE = hw/bsp/stm32f412disco/STM32F412ZGTx_FLASH.ld
|
||
|
|
|
||
|
|
SRC_C += \
|
||
|
|
$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \
|
||
|
|
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal.c \
|
||
|
|
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_cortex.c \
|
||
|
|
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_rcc.c \
|
||
|
|
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_rcc_ex.c \
|
||
|
|
$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_gpio.c
|
||
|
|
|
||
|
|
SRC_S += \
|
||
|
|
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f412zx.s
|
||
|
|
|
||
|
|
INC += \
|
||
|
|
$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
|
||
|
|
$(TOP)/$(ST_CMSIS)/Include \
|
||
|
|
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
||
|
|
$(TOP)/hw/bsp/$(BOARD)
|
||
|
|
|
||
|
|
# For TinyUSB port source
|
||
|
|
VENDOR = st
|
||
|
|
CHIP_FAMILY = stm32f4
|
||
|
|
|
||
|
|
# For freeRTOS port source
|
||
|
|
FREERTOS_PORT = ARM_CM4F
|
||
|
|
|
||
|
|
# For flash-jlink target
|
||
|
|
JLINK_DEVICE = stm32f41zx
|
||
|
|
JLINK_IF = swd
|
||
|
|
|
||
|
|
# Path to STM32 Cube Programmer CLI, should be added into system path
|
||
|
|
STM32Prog = STM32_Programmer_CLI
|
||
|
|
|
||
|
|
# flash target using on-board stlink
|
||
|
|
flash: $(BUILD)/$(BOARD)-firmware.elf
|
||
|
|
$(STM32Prog) --connect port=swd --write $< --go
|