2019-09-09 16:14:38 -04:00
|
|
|
CFLAGS += \
|
2019-11-20 16:06:40 +07:00
|
|
|
-flto \
|
|
|
|
|
-mthumb \
|
|
|
|
|
-mabi=aapcs-linux \
|
|
|
|
|
-mcpu=cortex-m0 \
|
|
|
|
|
-mfloat-abi=soft \
|
|
|
|
|
-nostdlib -nostartfiles \
|
|
|
|
|
-DSTM32F070xB \
|
|
|
|
|
-DCFG_EXAMPLE_MSC_READONLY \
|
|
|
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32F0
|
2019-09-09 16:14:38 -04:00
|
|
|
|
2019-09-27 00:15:43 +07:00
|
|
|
# mcu driver cause following warnings
|
|
|
|
|
CFLAGS += -Wno-error=unused-parameter
|
|
|
|
|
|
2019-09-09 16:14:38 -04:00
|
|
|
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F0xx_HAL_Driver
|
|
|
|
|
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F0xx
|
|
|
|
|
|
|
|
|
|
# All source paths should be relative to the top level.
|
2019-09-12 10:41:03 +07:00
|
|
|
LD_FILE = hw/bsp/$(BOARD)/stm32F070rbtx_flash.ld
|
2019-09-09 16:14:38 -04:00
|
|
|
|
|
|
|
|
SRC_C += \
|
2019-11-20 16:06:40 +07:00
|
|
|
$(ST_CMSIS)/Source/Templates/system_stm32f0xx.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal_cortex.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal_rcc_ex.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal_gpio.c \
|
|
|
|
|
$(ST_HAL_DRIVER)/Src/stm32f0xx_hal_uart.c
|
2019-09-09 16:14:38 -04:00
|
|
|
SRC_S += \
|
2019-11-20 16:06:40 +07:00
|
|
|
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f070xb.s
|
2019-09-09 16:14:38 -04:00
|
|
|
|
|
|
|
|
INC += \
|
2019-11-20 16:06:40 +07:00
|
|
|
$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
|
|
|
|
|
$(TOP)/$(ST_CMSIS)/Include \
|
|
|
|
|
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
|
|
|
|
$(TOP)/hw/bsp/$(BOARD)
|
2019-09-09 16:14:38 -04:00
|
|
|
|
|
|
|
|
# For TinyUSB port source
|
|
|
|
|
VENDOR = st
|
|
|
|
|
CHIP_FAMILY = stm32_fsdev
|
|
|
|
|
|
|
|
|
|
# For freeRTOS port source
|
2019-09-10 08:28:56 -04:00
|
|
|
FREERTOS_PORT = ARM_CM0
|
2019-09-09 16:14:38 -04:00
|
|
|
|
|
|
|
|
# For flash-jlink target
|
2019-09-10 08:28:56 -04:00
|
|
|
JLINK_DEVICE = stm32f070rb
|
2019-09-09 16:14:38 -04:00
|
|
|
JLINK_IF = swd
|
|
|
|
|
|
|
|
|
|
# Path to STM32 Cube Programmer CLI, should be added into system path
|
|
|
|
|
STM32Prog = STM32_Programmer_CLI
|
|
|
|
|
|
|
|
|
|
# flash target using on-board stlink
|
|
|
|
|
flash: $(BUILD)/$(BOARD)-firmware.elf
|
|
|
|
|
$(STM32Prog) --connect port=swd --write $< --go
|
