tinyUSB/hw/bsp/stm32f407disco/board.mk

CFLAGS += \
  -flto \
  -mthumb \
  -mabi=aapcs \
  -mcpu=cortex-m4 \
  -mfloat-abi=hard \
  -mfpu=fpv4-sp-d16 \
  -nostdlib -nostartfiles \
  -DSTM32F407xx \
  -DCFG_TUSB_MCU=OPT_MCU_STM32F4

# suppress warning caused by vendor mcu driver
CFLAGS += -Wno-error=cast-align

ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx

# All source paths should be relative to the top level.
LD_FILE = hw/bsp/$(BOARD)/STM32F407VGTx_FLASH.ld

SRC_C += \
	$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \
	$(ST_HAL_DRIVER)/Src/stm32f4xx_hal.c \
	$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_cortex.c \
	$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_rcc.c \
	$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_uart.c \
	$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_gpio.c

SRC_S += \
	$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f407xx.s

INC += \
	$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
	$(TOP)/$(ST_CMSIS)/Include \
	$(TOP)/$(ST_HAL_DRIVER)/Inc \
	$(TOP)/hw/bsp/$(BOARD)

# For TinyUSB port source
VENDOR = st
CHIP_FAMILY = synopsys

# For freeRTOS port source
FREERTOS_PORT = ARM_CM4F

# For flash-jlink target
JLINK_DEVICE = stm32f407vg
JLINK_IF = swd

# flash target using on-board stlink
flash: flash-stlink
fix pca10056 build error due to nrfx undef usage 2019-03-20 01:35:52 +07:00			`CFLAGS += \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-flto \`
clean up 2019-05-14 13:31:12 +07:00			`-mthumb \`
switch stm32f4 to use st_driver submodule 2019-09-05 22:12:43 +07:00			`-mabi=aapcs \`
clean up 2019-05-14 13:31:12 +07:00			`-mcpu=cortex-m4 \`
			`-mfloat-abi=hard \`
			`-mfpu=fpv4-sp-d16 \`
			`-nostdlib -nostartfiles \`
move -flto to board.mk current board that doesn work with flto is spresense and mimxrt10xx (due to xip image_vector_table is optimized out). 2019-11-20 16:06:40 +07:00			`-DSTM32F407xx \`
clean up 2019-05-14 13:31:12 +07:00			`-DCFG_TUSB_MCU=OPT_MCU_STM32F4`
needs to be filled out. blinks though 2018-11-27 18:11:03 -08:00
enable -Wcast-align suppress vendor sdk driver at board.mk 2020-05-17 14:24:15 +07:00			`# suppress warning caused by vendor mcu driver`
			`CFLAGS += -Wno-error=cast-align`

switch stm32f4 to use st_driver submodule 2019-09-05 22:12:43 +07:00			`ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F4xx_HAL_Driver`
			`ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F4xx`

needs to be filled out. blinks though 2018-11-27 18:11:03 -08:00			`# All source paths should be relative to the top level.`
ported stm32f2, added board stm32f207zg nucleo close #127 2019-09-12 10:41:03 +07:00			`LD_FILE = hw/bsp/$(BOARD)/STM32F407VGTx_FLASH.ld`
needs to be filled out. blinks though 2018-11-27 18:11:03 -08:00
			`SRC_C += \`
switch stm32f4 to use st_driver submodule 2019-09-05 22:12:43 +07:00			`$(ST_CMSIS)/Source/Templates/system_stm32f4xx.c \`
			`$(ST_HAL_DRIVER)/Src/stm32f4xx_hal.c \`
			`$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_cortex.c \`
			`$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_rcc.c \`
Update UARTs for stm32f4xx discovery boards. Other minor cleanups. 2020-03-28 11:19:50 -04:00			`$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_uart.c \`
switch stm32f3 to use st_driver 2019-09-05 22:41:58 +07:00			`$(ST_HAL_DRIVER)/Src/stm32f4xx_hal_gpio.c`
needs to be filled out. blinks though 2018-11-27 18:11:03 -08:00
			`SRC_S += \`
switch stm32f4 to use st_driver submodule 2019-09-05 22:12:43 +07:00			`$(ST_CMSIS)/Source/Templates/gcc/startup_stm32f407xx.s`
needs to be filled out. blinks though 2018-11-27 18:11:03 -08:00
			`INC += \`
switch stm32f4 to use st_driver submodule 2019-09-05 22:12:43 +07:00			`$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \`
			`$(TOP)/$(ST_CMSIS)/Include \`
			`$(TOP)/$(ST_HAL_DRIVER)/Inc \`
			`$(TOP)/hw/bsp/$(BOARD)`
stm32: Refactor so F4 and H7 use a single Synopsys IP source file. 2019-09-09 10:48:14 -04:00
add make.mk and rules.mk to help new makefile example 2019-05-01 14:27:17 +07:00			`# For TinyUSB port source`
Move all paths using "stm" to "st" subdirectories, update config.mk. 2019-02-27 09:15:07 -05:00			`VENDOR = st`
stm32: Refactor so F4 and H7 use a single Synopsys IP source file. 2019-09-09 10:48:14 -04:00			`CHIP_FAMILY = synopsys`
add flash target for stm32 board using stm32cubeprogammger cli 2019-03-09 01:04:26 +07:00
add make.mk and rules.mk to help new makefile example 2019-05-01 14:27:17 +07:00			`# For freeRTOS port source`
			`FREERTOS_PORT = ARM_CM4F`

			`# For flash-jlink target`
update flash-jlink target for m0 and m4 board 2019-03-17 15:42:57 +07:00			`JLINK_DEVICE = stm32f407vg`
add make.mk and rules.mk to help new makefile example 2019-05-01 14:27:17 +07:00			`JLINK_IF = swd`
update flash-jlink target for m0 and m4 board 2019-03-17 15:42:57 +07:00
adding flash (jlink) 2019-03-16 01:34:26 +07:00			`# flash target using on-board stlink`
clean up flash-stlink 2020-01-10 15:09:59 +07:00			`flash: flash-stlink`