add support for the QMTech ATMSAME70N19A board

hw/bsp/same70_qmtech/peripheral_clk_config.h

@@ -0,0 +1,126 @@
+/* Auto-generated config file peripheral_clk_config.h */
+#ifndef PERIPHERAL_CLK_CONFIG_H
+#define PERIPHERAL_CLK_CONFIG_H
+
+// <<< Use Configuration Wizard in Context Menu >>>
+
+/**
+ * \def CONF_HCLK_FREQUENCY
+ * \brief HCLK's Clock frequency
+ */
+#ifndef CONF_HCLK_FREQUENCY
+#define CONF_HCLK_FREQUENCY 300000000
+#endif
+
+/**
+ * \def CONF_FCLK_FREQUENCY
+ * \brief FCLK's Clock frequency
+ */
+#ifndef CONF_FCLK_FREQUENCY
+#define CONF_FCLK_FREQUENCY 300000000
+#endif
+
+/**
+ * \def CONF_CPU_FREQUENCY
+ * \brief CPU's Clock frequency
+ */
+#ifndef CONF_CPU_FREQUENCY
+#define CONF_CPU_FREQUENCY 300000000
+#endif
+
+/**
+ * \def CONF_SLCK_FREQUENCY
+ * \brief Slow Clock frequency
+ */
+#define CONF_SLCK_FREQUENCY 0
+
+/**
+ * \def CONF_MCK_FREQUENCY
+ * \brief Master Clock frequency
+ */
+#define CONF_MCK_FREQUENCY 150000000
+
+/**
+ * \def CONF_PCK6_FREQUENCY
+ * \brief Programmable Clock Controller 6 frequency
+ */
+#define CONF_PCK6_FREQUENCY 1714285
+
+// <h> USART Clock Settings
+// <o> USART Clock source
+
+// <0=> Master Clock (MCK)
+// <1=> MCK / 8 for USART
+// <2=> Programmable Clock Controller 4 (PMC_PCK4)
+// <3=> External Clock
+// <i> This defines the clock source for the USART
+// <id> usart_clock_source
+#ifndef CONF_USART1_CK_SRC
+#define CONF_USART1_CK_SRC 0
+#endif
+
+// <o> USART External Clock Input on SCK <1-4294967295>
+// <i> Inputs the external clock frequency on SCK
+// <id> usart_clock_freq
+#ifndef CONF_USART1_SCK_FREQ
+#define CONF_USART1_SCK_FREQ 10000000
+#endif
+
+// </h>
+
+/**
+ * \def USART FREQUENCY
+ * \brief USART's Clock frequency
+ */
+#ifndef CONF_USART1_FREQUENCY
+#define CONF_USART1_FREQUENCY 150000000
+#endif
+
+#ifndef CONF_SRC_USB_480M
+#define CONF_SRC_USB_480M 0
+#endif
+
+#ifndef CONF_SRC_USB_48M
+#define CONF_SRC_USB_48M 1
+#endif
+
+// <y> USB Full/Low Speed Clock
+// <CONF_SRC_USB_48M"> USB Clock Controller (USB_48M)
+// <id> usb_fsls_clock_source
+// <i> 48MHz clock source for low speed and full speed.
+// <i> It must be available when low speed is supported by host driver.
+// <i> It must be available when low power mode is selected.
+#ifndef CONF_USBHS_FSLS_SRC
+#define CONF_USBHS_FSLS_SRC CONF_SRC_USB_48M
+#endif
+
+// <y> USB Clock Source(Normal/Low-power Mode Selection)
+// <CONF_SRC_USB_480M"> USB High Speed Clock (USB_480M)
+// <CONF_SRC_USB_48M"> USB Clock Controller (USB_48M)
+// <id> usb_clock_source
+// <i> Select the clock source for USB.
+// <i> In normal mode, use "USB High Speed Clock (USB_480M)".
+// <i> In low-power mode, use "USB Clock Controller (USB_48M)".
+#ifndef CONF_USBHS_SRC
+#define CONF_USBHS_SRC CONF_SRC_USB_480M
+#endif
+
+/**
+ * \def CONF_USBHS_FSLS_FREQUENCY
+ * \brief USBHS's Full/Low Speed Clock Source frequency
+ */
+#ifndef CONF_USBHS_FSLS_FREQUENCY
+#define CONF_USBHS_FSLS_FREQUENCY 48000000
+#endif
+
+/**
+ * \def CONF_USBHS_FREQUENCY
+ * \brief USBHS's Selected Clock Source frequency
+ */
+#ifndef CONF_USBHS_FREQUENCY
+#define CONF_USBHS_FREQUENCY 480000000
+#endif
+
+// <<< end of configuration section >>>
+
+#endif // PERIPHERAL_CLK_CONFIG_H