change at86rf to 1ghznode

rom device runs ok with lpc11uxx

demos/bsp/boards/microbuilder/board_rf1ghznode.c

@@ -0,0 +1,88 @@
+/**************************************************************************/
+/*!
+    @file     board_rf1ghznode.c
+    @author   hathach (tinyusb.org)
+
+    @section LICENSE
+
+    Software License Agreement (BSD License)
+
+    Copyright (c) 2013, hathach (tinyusb.org)
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions are met:
+    1. Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+    2. Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in the
+    documentation and/or other materials provided with the distribution.
+    3. Neither the name of the copyright holders nor the
+    names of its contributors may be used to endorse or promote products
+    derived from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
+    EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+    DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
+    DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+    LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
+    ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+    INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
+    SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+    This file is part of the tinyusb stack.
+*/
+/**************************************************************************/
+
+#include "../board.h"
+
+#if BOARD == BOARD_RF1GHZNODE
+
+void board_init(void)
+{
+  SystemInit();
+  SysTick_Config(SystemCoreClock / CFG_TICKS_PER_SECOND); // 1 msec tick timer
+  GPIOInit();
+
+  GPIOSetDir(CFG_LED_PORT, CFG_LED_PIN, 1);
+  board_leds(0x01, 0); // turn off the led first
+
+#if CFG_UART_ENABLE
+  UARTInit(CFG_UART_BAUDRATE);
+#endif
+}
+
+//--------------------------------------------------------------------+
+// LEDS
+//--------------------------------------------------------------------+
+void board_leds(uint32_t on_mask, uint32_t off_mask)
+{
+  if (on_mask & BIT_(0))
+  {
+    GPIOSetBitValue(CFG_LED_PORT, CFG_LED_PIN, CFG_LED_ON);
+  }else if (off_mask & BIT_(0))
+  {
+    GPIOSetBitValue(CFG_LED_PORT, CFG_LED_PIN, CFG_LED_OFF);
+  }
+}
+
+//--------------------------------------------------------------------+
+// UART
+//--------------------------------------------------------------------+
+#if CFG_UART_ENABLE
+uint32_t board_uart_send(uint8_t *buffer, uint32_t length)
+{
+  UARTSend(buffer, length);
+  return length;
+}
+
+uint32_t board_uart_recv(uint8_t *buffer, uint32_t length)
+{
+//  *buffer = get_key(); TODO cannot find available code for uart getchar
+  return 0;
+}
+#endif
+
+#endif