enable stm32f4 host

examples/host/cdc_msc_hid/only.txt

@@ -12,4 +12,5 @@ mcu:MSP432E4
 mcu:RX65X
 mcu:RAXXX
 mcu:MAX3421
+mcu:STM32F4
 mcu:STM32F7

examples/host/msc_file_explorer/only.txt

@@ -12,4 +12,5 @@ mcu:MSP432E4
 mcu:RX65X
 mcu:RAXXX
 mcu:MAX3421
+mcu:STM32F4
 mcu:STM32F7

hw/bsp/stm32f4/boards/feather_stm32f405/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F405RGTx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F405xx
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/feather_stm32f405/board.h

@@ -31,22 +31,35 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOC
-#define LED_PIN               GPIO_PIN_1
-#define LED_STATE_ON          1
-
-// Button: Pin D5
-#define BUTTON_PORT           GPIOC
-#define BUTTON_PIN            GPIO_PIN_7
-#define BUTTON_STATE_ACTIVE   0
-
-// UART
 #define UART_DEV              USART3
-#define UART_GPIO_PORT        GPIOB
+
-#define UART_GPIO_AF          GPIO_AF7_USART3
+#define PINID_LED      0
-#define UART_TX_PIN           GPIO_PIN_10
+#define PINID_BUTTON   1
-#define UART_RX_PIN           GPIO_PIN_11
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_4, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // BUTTON
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_7, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // UART TX
+    .port = GPIOB,
+    .pin_init = { .Pin = GPIO_PIN_10, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOB,
+    .pin_init = { .Pin = GPIO_PIN_11, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -84,18 +97,21 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOB_CLK_ENABLE();
-  __HAL_RCC_GPIOC_CLK_ENABLE();
   __HAL_RCC_USART3_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if  (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  (void) rhport; (void) state;
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/pyboardv11/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F405RGTx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F405xx
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/pyboardv11/board.h

@@ -31,22 +31,35 @@
  extern "C" {
 #endif
 
-// Blue LED is chosen because the other LEDs are connected to ST-LINK lines.
+#define UART_DEV              USART2
-#define LED_PORT              GPIOB
-#define LED_PIN               GPIO_PIN_4
-#define LED_STATE_ON          1
 
-#define BUTTON_PORT           GPIOB
+#define PINID_LED      0
-#define BUTTON_PIN            GPIO_PIN_3
+#define PINID_BUTTON   1
-#define BUTTON_STATE_ACTIVE   1
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
 
-// Enable PA2 as the debug log UART
+static board_pindef_t board_pindef[] = {
-// It is not routed to the ST/Link on the Discovery board.
+  { // LED
-//#define UART_DEV              USART2
+    .port = GPIOB,
-//#define UART_GPIO_PORT        GPIOA
+    .pin_init = { .Pin = GPIO_PIN_4, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
-//#define UART_GPIO_AF          GPIO_AF7_USART2
+    .active_state = 1
-//#define UART_TX_PIN           GPIO_PIN_2
+  },
-//#define UART_RX_PIN           GPIO_PIN_3
+  { // BUTTON
+    .port = GPIOB,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -84,16 +97,21 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if  (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  (void) rhport; (void) state;
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f401blackpill/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F401VCTx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F405xx
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f401blackpill/board.h

@@ -31,23 +31,36 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOC
-#define LED_PIN               GPIO_PIN_13
-#define LED_STATE_ON          0
-
-// Button
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   0
-
 // Enable PA2 as the debug log UART
-//#define UART_DEV              USART2
+#define UART_DEV              USART2
-//#define UART_GPIO_PORT        GPIOA
-//#define UART_GPIO_AF          GPIO_AF7_USART2
-//#define UART_TX_PIN           GPIO_PIN_2
-//#define UART_RX_PIN           GPIO_PIN_3
 
+#define PINID_LED      0
+#define PINID_BUTTON   1
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_13, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // BUTTON
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -85,19 +98,22 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_USART2_CLK_ENABLE();
-  __HAL_RCC_GPIOC_CLK_ENABLE();
-  //__HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
   // Blackpill doesn't use VBUS sense (B device) explicitly disable it
+  if  (rhport == 0) {
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSBSEN;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSASEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  (void) rhport; (void) state;
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f407blackvet/board.cmake

@@ -7,7 +7,5 @@ function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F407xx
     HSE_VALUE=8000000
-    BOARD_TUD_RHPORT=0
-    BOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f407blackvet/board.h

@@ -31,24 +31,36 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOA
-#define LED_PIN               GPIO_PIN_6
-#define LED_STATE_ON          1
-
-// Button
-#define BUTTON_PORT           GPIOE
-#define BUTTON_PIN            GPIO_PIN_4
-#define BUTTON_STATE_ACTIVE   0
-
 // Enable PA2 as the debug log UART
-// It is not routed to the ST/Link on the Discovery board.
 #define UART_DEV              USART2
-#define UART_GPIO_PORT        GPIOA
-#define UART_GPIO_AF          GPIO_AF7_USART2
-#define UART_TX_PIN           GPIO_PIN_2
-#define UART_RX_PIN           GPIO_PIN_3
 
+#define PINID_LED      0
+#define PINID_BUTTON   1
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_6, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // BUTTON
+    .port = GPIOE,
+    .pin_init = { .Pin = GPIO_PIN_4, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+};
 //--------------------------------------------------------------------+
 // RCC Clock
 //--------------------------------------------------------------------+
@@ -86,19 +98,21 @@ static inline void board_clock_init(void)
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
 
   // Enable clocks for LED, Button, Uart
-  __HAL_RCC_GPIOA_CLK_ENABLE();
-  __HAL_RCC_GPIOE_CLK_ENABLE();
-  __HAL_RCC_GPIOH_CLK_ENABLE();
   __HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if (rhport == 0) {
     // Black F407VET6 doesn't use VBUS sense (B device) explicitly disable it
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSBSEN;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSASEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  (void) rhport; (void) state;
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f407disco/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F407VGTx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F407xx
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f407disco/board.h

@@ -31,23 +31,43 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOD
-#define LED_PIN               GPIO_PIN_14
-#define LED_STATE_ON          1
-
-// Button
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
 // Enable PA2 as the debug log UART
 // It is not routed to the ST/Link on the Discovery board.
 #define UART_DEV              USART2
-#define UART_GPIO_PORT        GPIOA
+
-#define UART_GPIO_AF          GPIO_AF7_USART2
+#define PINID_LED      0
-#define UART_TX_PIN           GPIO_PIN_2
+#define PINID_BUTTON   1
-#define UART_RX_PIN           GPIO_PIN_3
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+#define PINID_VBUS0_EN 4
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_14, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // BUTTON
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // VBUS0 EN
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_NOPULL, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  }
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -85,18 +105,24 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks Uart
-  __HAL_RCC_GPIOA_CLK_ENABLE();
-  __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  if (rhport == 0) {
+    board_pindef_t* pindef = &board_pindef[PINID_VBUS0_EN];
+    HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
+  }
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f411blackpill/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F411CEUx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F411xE
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f411blackpill/board.h

@@ -31,23 +31,35 @@
  extern "C" {
 #endif
 
-// LED
+#define UART_DEV              USART2
-#define LED_PORT              GPIOC
-#define LED_PIN               GPIO_PIN_13
-#define LED_STATE_ON          0
 
-// Button
+#define PINID_LED      0
-#define BUTTON_PORT           GPIOA
+#define PINID_BUTTON   1
-#define BUTTON_PIN            GPIO_PIN_0
+#define PINID_UART_TX  2
-#define BUTTON_STATE_ACTIVE   0
+#define PINID_UART_RX  3
-
-// Enable PA2 as the debug log UART
-//#define UART_DEV              USART2
-//#define UART_GPIO_PORT        GPIOA
-//#define UART_GPIO_AF          GPIO_AF7_USART2
-//#define UART_TX_PIN           GPIO_PIN_2
-//#define UART_RX_PIN           GPIO_PIN_3
 
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_13, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // BUTTON
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -85,19 +97,22 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_USART2_CLK_ENABLE();
-  __HAL_RCC_GPIOC_CLK_ENABLE();
-  //__HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
   // Blackpill doesn't use VBUS sense (B device) explicitly disable it
+  if  (rhport == 0) {
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSBSEN;
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBUSASEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  (void) rhport; (void) state;
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f411disco/board.cmake

@@ -6,6 +6,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F411VETx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F411xE
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f411disco/board.h

@@ -31,28 +31,46 @@
  extern "C" {
 #endif
 
-// Orange LED
-#define LED_PORT              GPIOD
-#define LED_PIN               GPIO_PIN_13
-#define LED_STATE_ON          1
-
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
-// Enable PA2 as the debug log UART
 #define UART_DEV              USART2
-#define UART_GPIO_PORT        GPIOA
-#define UART_GPIO_AF          GPIO_AF7_USART2
-#define UART_TX_PIN           GPIO_PIN_2
-#define UART_RX_PIN           GPIO_PIN_3
 
+#define PINID_LED      0
+#define PINID_BUTTON   1
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+#define PINID_VBUS0_EN 4
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_13, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // BUTTON
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // VBUS0 EN
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_NOPULL, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  }
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
 //--------------------------------------------------------------------+
-static inline void board_clock_init(void)
+static inline void board_clock_init(void) {
-{
   RCC_ClkInitTypeDef RCC_ClkInitStruct;
   RCC_OscInitTypeDef RCC_OscInitStruct;
 
@@ -84,18 +102,24 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for UART
-  __HAL_RCC_GPIOA_CLK_ENABLE();
-  __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
   // Enable VBUS sense (B device) via pin PA9
+  if (rhport == 0) {
     USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  if (rhport == 0) {
+    board_pindef_t* pindef = &board_pindef[PINID_VBUS0_EN];
+    HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
+  }
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f412disco/board.cmake

@@ -7,6 +7,5 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32F412ZGTx_FLASH.ld)
 function(update_board TARGET)
   target_compile_definitions(${TARGET} PUBLIC
     STM32F412Zx
-    BOARD_TUD_RHPORT=0
     )
 endfunction()

hw/bsp/stm32f4/boards/stm32f412disco/board.h

@@ -43,16 +43,45 @@
 
 // UART Enable PA2 as the debug log UART
 #define UART_DEV              USART2
-#define UART_GPIO_PORT        GPIOA
+
-#define UART_GPIO_AF          GPIO_AF7_USART2
+#define PINID_LED      0
-#define UART_TX_PIN           GPIO_PIN_2
+#define PINID_BUTTON   1
-#define UART_RX_PIN           GPIO_PIN_3
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+#define PINID_VBUS0_EN 4
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOE,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // BUTTON
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_0, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_2, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOA,
+    .pin_init = { .Pin = GPIO_PIN_3, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART2 },
+    .active_state = 0
+  },
+  { // VBUS0 EN
+    .port = GPIOG,
+    .pin_init = { .Pin = GPIO_PIN_8, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_NOPULL, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  }
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
 //--------------------------------------------------------------------+
-static inline void board_clock_init(void)
+static inline void board_clock_init(void) {
-{
   RCC_ClkInitTypeDef RCC_ClkInitStruct;
   RCC_OscInitTypeDef RCC_OscInitStruct;
   RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
@@ -99,17 +128,24 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOA_CLK_ENABLE();
-  __HAL_RCC_GPIOE_CLK_ENABLE();
   __HAL_RCC_USART2_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  if (rhport == 0) {
+    board_pindef_t* pindef = &board_pindef[PINID_VBUS0_EN];
+    HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
+  }
+}
+
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f412nucleo/board.h

@@ -31,22 +31,42 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOB
-#define LED_PIN               GPIO_PIN_14
-#define LED_STATE_ON          0
-
-// Button
-#define BUTTON_PORT           GPIOC
-#define BUTTON_PIN            GPIO_PIN_13
-#define BUTTON_STATE_ACTIVE   1
-
 // UART Enable for STLink VCOM
 #define UART_DEV              USART3
-#define UART_GPIO_PORT        GPIOD
+
-#define UART_GPIO_AF          GPIO_AF7_USART3
+#define PINID_LED      0
-#define UART_TX_PIN           GPIO_PIN_8
+#define PINID_BUTTON   1
-#define UART_RX_PIN           GPIO_PIN_9
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+#define PINID_VBUS0_EN 4
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOB,
+    .pin_init = { .Pin = GPIO_PIN_14, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // BUTTON
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_13, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_8, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_9, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+  { // VBUS0 EN
+    .port = GPIOG,
+    .pin_init = { .Pin = GPIO_PIN_6, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  }
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -99,18 +119,23 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks for Uart
-  __HAL_RCC_GPIOB_CLK_ENABLE();
-  __HAL_RCC_GPIOC_CLK_ENABLE();
-  __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_USART3_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  if (rhport == 0) {
+    board_pindef_t* pindef = &board_pindef[PINID_VBUS0_EN];
+    HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
+  }
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/boards/stm32f439nucleo/board.h

@@ -31,22 +31,43 @@
  extern "C" {
 #endif
 
-// LED
-#define LED_PORT              GPIOB
-#define LED_PIN               GPIO_PIN_14
-#define LED_STATE_ON          0
-
-// Button
-#define BUTTON_PORT           GPIOC
-#define BUTTON_PIN            GPIO_PIN_13
-#define BUTTON_STATE_ACTIVE   1
 
 // UART Enable for STLink VCOM
 #define UART_DEV              USART3
-#define UART_GPIO_PORT        GPIOD
+
-#define UART_GPIO_AF          GPIO_AF7_USART3
+#define PINID_LED      0
-#define UART_TX_PIN           GPIO_PIN_8
+#define PINID_BUTTON   1
-#define UART_RX_PIN           GPIO_PIN_9
+#define PINID_UART_TX  2
+#define PINID_UART_RX  3
+#define PINID_VBUS0_EN 4
+
+static board_pindef_t board_pindef[] = {
+  { // LED
+    .port = GPIOB,
+    .pin_init = { .Pin = GPIO_PIN_14, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 0
+  },
+  { // BUTTON
+    .port = GPIOC,
+    .pin_init = { .Pin = GPIO_PIN_13, .Mode = GPIO_MODE_INPUT, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  },
+  { // UART TX
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_8, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+  { // UART RX
+    .port = GPIOD,
+    .pin_init = { .Pin = GPIO_PIN_9, .Mode = GPIO_MODE_AF_PP, .Pull = GPIO_PULLUP, .Speed = GPIO_SPEED_HIGH, .Alternate = GPIO_AF7_USART3 },
+    .active_state = 0
+  },
+  { // VBUS0 EN
+    .port = GPIOG,
+    .pin_init = { .Pin = GPIO_PIN_6, .Mode = GPIO_MODE_OUTPUT_PP, .Pull = GPIO_PULLDOWN, .Speed = GPIO_SPEED_HIGH, .Alternate = 0 },
+    .active_state = 1
+  }
+};
 
 //--------------------------------------------------------------------+
 // RCC Clock
@@ -87,19 +108,24 @@ static inline void board_clock_init(void)
   RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
 
-  // Enable clocks for LED, Button, Uart
+  // Enable clocks Uart
-  __HAL_RCC_GPIOB_CLK_ENABLE();
-  __HAL_RCC_GPIOC_CLK_ENABLE();
-  __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_USART3_CLK_ENABLE();
 }
 
-static inline void board_vbus_sense_init(void)
+static inline void board_vbus_sense_init(uint8_t rhport) {
-{
+  if (rhport == 0) {
     // Enable VBUS sense (B device) via pin PA9
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS;
     USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
   }
+}
+
+static inline void board_vbus_set(uint8_t rhport, bool state) {
+  if (rhport == 0) {
+    board_pindef_t* pindef = &board_pindef[PINID_VBUS0_EN];
+    HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET);
+  }
+}
 
 #ifdef __cplusplus
  }

hw/bsp/stm32f4/family.c

@@ -26,6 +26,13 @@
 
 #include "stm32f4xx_hal.h"
 #include "bsp/board_api.h"
+
+typedef struct {
+  GPIO_TypeDef* port;
+  GPIO_InitTypeDef pin_init;
+  uint8_t active_state;
+} board_pindef_t;
+
 #include "board.h"
 
 //--------------------------------------------------------------------+
@@ -42,12 +49,49 @@ void OTG_HS_IRQHandler(void) {
 //--------------------------------------------------------------------+
 // MACRO TYPEDEF CONSTANT ENUM
 //--------------------------------------------------------------------+
-UART_HandleTypeDef UartHandle;
+UART_HandleTypeDef UartHandle = {
+    .Instance = UART_DEV,
+    .Init = {
+      .BaudRate   = CFG_BOARD_UART_BAUDRATE,
+      .WordLength = UART_WORDLENGTH_8B,
+      .StopBits   = UART_STOPBITS_1,
+      .Parity     = UART_PARITY_NONE,
+      .HwFlowCtl  = UART_HWCONTROL_NONE,
+      .Mode       = UART_MODE_TX_RX,
+      .OverSampling = UART_OVERSAMPLING_16
+    }
+};
 
 void board_init(void) {
   board_clock_init();
   //SystemCoreClockUpdate();
 
+  // Enable All GPIOs clocks
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+#ifdef __HAL_RCC_GPIOE_CLK_ENABLE
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+#endif
+#ifdef __HAL_RCC_GPIOF_CLK_ENABLE
+  __HAL_RCC_GPIOF_CLK_ENABLE();
+#endif
+#ifdef __HAL_RCC_GPIOG_CLK_ENABLE
+  __HAL_RCC_GPIOG_CLK_ENABLE();
+#endif
+  __HAL_RCC_GPIOH_CLK_ENABLE();
+#ifdef __HAL_RCC_GPIOI_CLK_ENABLE
+  __HAL_RCC_GPIOI_CLK_ENABLE();
+#endif
+#ifdef __HAL_RCC_GPIOJ_CLK_ENABLE
+  __HAL_RCC_GPIOJ_CLK_ENABLE();
+#endif
+
+  for (uint8_t i = 0; i < TU_ARRAY_SIZE(board_pindef); i++) {
+    HAL_GPIO_Init(board_pindef[i].port, &board_pindef[i].pin_init);
+  }
+
 #if CFG_TUSB_OS == OPT_OS_NONE
   // 1ms tick timer
   SysTick_Config(SystemCoreClock / 1000);
@@ -59,49 +103,14 @@ void board_init(void) {
   NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
 #endif
 
-  GPIO_InitTypeDef GPIO_InitStruct;
-
-  // LED
-  GPIO_InitStruct.Pin = LED_PIN;
-  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
-  GPIO_InitStruct.Pull = GPIO_PULLUP;
-  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
-  HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
-
   board_led_write(false);
 
-  // Button
-  GPIO_InitStruct.Pin = BUTTON_PIN;
-  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
-  GPIO_InitStruct.Pull = BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN : GPIO_PULLUP;
-  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
-  HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
-
 #ifdef UART_DEV
-  // UART
-  GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN;
-  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
-  GPIO_InitStruct.Pull = GPIO_PULLUP;
-  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
-  GPIO_InitStruct.Alternate = UART_GPIO_AF;
-  HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct);
-
-  UartHandle = (UART_HandleTypeDef) {
-      .Instance        = UART_DEV,
-      .Init.BaudRate   = CFG_BOARD_UART_BAUDRATE,
-      .Init.WordLength = UART_WORDLENGTH_8B,
-      .Init.StopBits   = UART_STOPBITS_1,
-      .Init.Parity     = UART_PARITY_NONE,
-      .Init.HwFlowCtl  = UART_HWCONTROL_NONE,
-      .Init.Mode       = UART_MODE_TX_RX,
-      .Init.OverSampling = UART_OVERSAMPLING_16
-  };
   HAL_UART_Init(&UartHandle);
 #endif
 
-#if BOARD_TUD_RHPORT == 0
+  //------------- USB FS -------------//
-  /* Configure USB FS GPIOs */
+  GPIO_InitTypeDef GPIO_InitStruct;
-  __HAL_RCC_GPIOA_CLK_ENABLE();
 
   /* Configure USB D+ D- Pins */
   GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12;
@@ -127,11 +136,9 @@ void board_init(void) {
 
   // Enable USB OTG clock
   __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
-#else
-  /* Configure USB HS GPIOs */
-  __HAL_RCC_GPIOB_CLK_ENABLE();
 
-  /* Configure USB D+ D- Pins */
+  //------------- USB HS -------------//
+#ifdef __HAL_RCC_USB_OTG_HS_CLK_ENABLE
   GPIO_InitStruct.Pin = GPIO_PIN_14 | GPIO_PIN_15;
   GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
   GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
@@ -166,7 +173,13 @@ void board_init(void) {
   HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
 #endif
 
-  board_vbus_sense_init();
+#if CFG_TUD_ENABLED
+  board_vbus_sense_init(BOARD_TUD_RHPORT);
+#endif
+
+#if CFG_TUH_ENABLED
+  board_vbus_set(BOARD_TUD_RHPORT, true);
+#endif
 }
 
 //--------------------------------------------------------------------+
@@ -174,12 +187,22 @@ void board_init(void) {
 //--------------------------------------------------------------------+
 
 void board_led_write(bool state) {
-  GPIO_PinState pin_state = (GPIO_PinState) (state ? LED_STATE_ON : (1 - LED_STATE_ON));
+#ifdef PINID_LED
-  HAL_GPIO_WritePin(LED_PORT, LED_PIN, pin_state);
+  board_pindef_t* pindef = &board_pindef[PINID_LED];
+  GPIO_PinState pin_state = state == pindef->active_state ? GPIO_PIN_SET : GPIO_PIN_RESET;
+  HAL_GPIO_WritePin(pindef->port, pindef->pin_init.Pin, pin_state);
+#else
+  (void) state;
+#endif
 }
 
 uint32_t board_button_read(void) {
-  return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+#ifdef PINID_BUTTON
+  board_pindef_t* pindef = &board_pindef[PINID_BUTTON];
+  return pindef->active_state == HAL_GPIO_ReadPin(pindef->port, pindef->pin_init.Pin);
+#else
+  return 0;
+#endif
 }
 
 size_t board_get_unique_id(uint8_t id[], size_t max_len) {

hw/bsp/stm32f4/family.cmake

@@ -16,6 +16,28 @@ set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOL
 
 set(FAMILY_MCUS STM32F4 CACHE INTERNAL "")
 
+# ----------------------
+# Port & Speed Selection
+# ----------------------
+if (NOT DEFINED RHPORT_DEVICE)
+  set(RHPORT_DEVICE 0)
+endif ()
+if (NOT DEFINED RHPORT_HOST)
+  set(RHPORT_HOST 0)
+endif ()
+
+if (NOT DEFINED RHPORT_SPEED)
+  # Most F7 does not has built-in HS PHY
+  set(RHPORT_SPEED OPT_MODE_FULL_SPEED OPT_MODE_FULL_SPEED)
+endif ()
+if (NOT DEFINED RHPORT_DEVICE_SPEED)
+  list(GET RHPORT_SPEED ${RHPORT_DEVICE} RHPORT_DEVICE_SPEED)
+endif ()
+if (NOT DEFINED RHPORT_HOST_SPEED)
+  list(GET RHPORT_SPEED ${RHPORT_HOST} RHPORT_HOST_SPEED)
+endif ()
+
+cmake_print_variables(RHPORT_DEVICE RHPORT_DEVICE_SPEED RHPORT_HOST RHPORT_HOST_SPEED)
 
 #------------------------------------
 # BOARD_TARGET
@@ -52,8 +74,12 @@ function(add_board_target BOARD_TARGET)
     ${ST_CMSIS}/Include
     ${ST_HAL_DRIVER}/Inc
     )
-  # target_compile_options(${BOARD_TARGET} PUBLIC)
+  target_compile_definitions(${BOARD_TARGET} PUBLIC
-  # target_compile_definitions(${BOARD_TARGET} PUBLIC)
+    BOARD_TUD_RHPORT=${RHPORT_DEVICE}
+    BOARD_TUD_MAX_SPEED=${RHPORT_DEVICE_SPEED}
+    BOARD_TUH_RHPORT=${RHPORT_HOST}
+    BOARD_TUH_MAX_SPEED=${RHPORT_HOST_SPEED}
+    )
 
   update_board(${BOARD_TARGET})
 

hw/bsp/stm32f4/family.mk

@@ -8,14 +8,40 @@ ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
 include $(TOP)/$(BOARD_PATH)/board.mk
 CPU_CORE ?= cortex-m4
 
-PORT ?= 0
+# ----------------------
+# Port & Speed Selection
+# ----------------------
+RHPORT_SPEED ?= OPT_MODE_FULL_SPEED OPT_MODE_FULL_SPEED
+RHPORT_DEVICE ?= 0
+RHPORT_HOST ?= 0
+
+# Determine RHPORT_DEVICE_SPEED if not defined
+ifndef RHPORT_DEVICE_SPEED
+ifeq ($(RHPORT_DEVICE), 0)
+  RHPORT_DEVICE_SPEED = $(firstword $(RHPORT_SPEED))
+else
+  RHPORT_DEVICE_SPEED = $(lastword $(RHPORT_SPEED))
+endif
+endif
+
+# Determine RHPORT_HOST_SPEED if not defined
+ifndef RHPORT_HOST_SPEED
+ifeq ($(RHPORT_HOST), 0)
+  RHPORT_HOST_SPEED = $(firstword $(RHPORT_SPEED))
+else
+  RHPORT_HOST_SPEED = $(lastword $(RHPORT_SPEED))
+endif
+endif
 
 # --------------
 # Compiler Flags
 # --------------
 CFLAGS += \
   -DCFG_TUSB_MCU=OPT_MCU_STM32F4 \
-  -DBOARD_TUD_RHPORT=$(PORT)
+	-DBOARD_TUD_RHPORT=${RHPORT_DEVICE} \
+	-DBOARD_TUD_MAX_SPEED=${RHPORT_DEVICE_SPEED} \
+	-DBOARD_TUH_RHPORT=${RHPORT_HOST} \
+	-DBOARD_TUH_MAX_SPEED=${RHPORT_HOST_SPEED} \
 
 # GCC Flags
 CFLAGS_GCC += \

hw/bsp/stm32f7/family.cmake

@@ -16,6 +16,16 @@ set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOL
 
 set(FAMILY_MCUS STM32F7 CACHE INTERNAL "")
 
+# ----------------------
+# Port & Speed Selection
+# ----------------------
+if (NOT DEFINED RHPORT_DEVICE)
+  set(RHPORT_DEVICE 0)
+endif ()
+if (NOT DEFINED RHPORT_HOST)
+  set(RHPORT_HOST 0)
+endif ()
+
 if (NOT DEFINED RHPORT_SPEED)
   # Most F7 does not has built-in HS PHY
   set(RHPORT_SPEED OPT_MODE_FULL_SPEED OPT_MODE_FULL_SPEED)

hw/bsp/stm32f7/family.mk

@@ -8,8 +8,12 @@ ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
 include $(TOP)/$(BOARD_PATH)/board.mk
 CPU_CORE ?= cortex-m7-fpsp
 
-# Default RHPORT_SPEED if not defined
+# ----------------------
+# Port & Speed Selection
+# ----------------------
 RHPORT_SPEED ?= OPT_MODE_FULL_SPEED OPT_MODE_FULL_SPEED
+RHPORT_DEVICE ?= 0
+RHPORT_HOST ?= 0
 
 # Determine RHPORT_DEVICE_SPEED if not defined
 ifndef RHPORT_DEVICE_SPEED
@@ -34,20 +38,23 @@ endif
 # --------------
 CFLAGS += \
   -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \
-  -DBOARD_TUD_RHPORT=$(PORT)
+	-DBOARD_TUD_RHPORT=${RHPORT_DEVICE} \
+	-DBOARD_TUD_MAX_SPEED=${RHPORT_DEVICE_SPEED} \
+	-DBOARD_TUH_RHPORT=${RHPORT_HOST} \
+	-DBOARD_TUH_MAX_SPEED=${RHPORT_HOST_SPEED} \
 
-ifeq ($(PORT), 1)
+#ifeq ($(PORT), 1)
-  ifeq ($(SPEED), high)
+#  ifeq ($(SPEED), high)
-    CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED
+#    CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED
-    $(info "Using OTG_HS in HighSpeed mode")
+#    $(info "Using OTG_HS in HighSpeed mode")
-  else
+#  else
-    CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+#    CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
-    $(info "Using OTG_HS in FullSpeed mode")
+#    $(info "Using OTG_HS in FullSpeed mode")
-  endif
+#  endif
-else
+#else
-  CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+#  CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
-  $(info "Using OTG_FS")
+#  $(info "Using OTG_FS")
-endif
+#endif
 
 # GCC Flags
 CFLAGS_GCC += \