diff --git a/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.h b/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.h new file mode 100644 index 000000000..7c527e2c2 --- /dev/null +++ b/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.h @@ -0,0 +1,93 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED +#define LED_PORT GPIOA +#define LED_PIN GPIO_PIN_5 +#define LED_STATE_ON 1 + +// Button +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_DEV USART2 +#define UART_CLK_EN __HAL_RCC_USART2_CLK_ENABLE +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF1_USART2 +#define UART_TX_PIN GPIO_PIN_2 +#define UART_RX_PIN GPIO_PIN_3 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32f0_clock_init(void) +{ + /* Configure the system clock to 48 MHz */ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; + + /* Enable HSE Oscillator and activate PLL with 8 MHz HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6; + RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 + clocks dividers */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); + + + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) ; +} + +static inline void board_vbus_sense_init(void) +{ +} + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.mk b/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.mk new file mode 100644 index 000000000..9e636cd76 --- /dev/null +++ b/hw/bsp/stm32f0/boards/stm32f070rbnucleo/board.mk @@ -0,0 +1,11 @@ +CFLAGS += -DSTM32F070xB + +LD_FILE = $(BOARD_PATH)/stm32F070rbtx_flash.ld + +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f070xb.s + +# For flash-jlink target +JLINK_DEVICE = stm32f070rb + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld b/hw/bsp/stm32f0/boards/stm32f070rbnucleo/stm32F070rbtx_flash.ld similarity index 100% rename from hw/bsp/stm32f070rbnucleo/stm32F070rbtx_flash.ld rename to hw/bsp/stm32f0/boards/stm32f070rbnucleo/stm32F070rbtx_flash.ld diff --git a/hw/bsp/stm32f0/boards/stm32f072disco/board.h b/hw/bsp/stm32f0/boards/stm32f072disco/board.h new file mode 100644 index 000000000..0b1824b8e --- /dev/null +++ b/hw/bsp/stm32f0/boards/stm32f072disco/board.h @@ -0,0 +1,85 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED +#define LED_PORT GPIOC +#define LED_PIN GPIO_PIN_6 +#define LED_STATE_ON 1 + +// Button +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + +// UART +#define UART_DEV USART1 +#define UART_CLK_EN __HAL_RCC_USART1_CLK_ENABLE +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF1_USART1 +#define UART_TX_PIN GPIO_PIN_9 +#define UART_RX_PIN GPIO_PIN_10 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32f0_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Select HSI48 Oscillator as PLL source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48; + RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI48; + RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Select PLL as system clock source and configure the HCLK and PCLK1 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); +} + +static inline void board_vbus_sense_init(void) +{ +} + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32f0/boards/stm32f072disco/board.mk b/hw/bsp/stm32f0/boards/stm32f072disco/board.mk new file mode 100644 index 000000000..2ef0ee63c --- /dev/null +++ b/hw/bsp/stm32f0/boards/stm32f072disco/board.mk @@ -0,0 +1,11 @@ +CFLAGS += -DSTM32F072xB + +LD_FILE = $(BOARD_PATH)/STM32F072RBTx_FLASH.ld + +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f072xb.s + +# For flash-jlink target +JLINK_DEVICE = stm32f072rb + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f0/family.c b/hw/bsp/stm32f0/family.c index 2815beef4..16c734405 100644 --- a/hw/bsp/stm32f0/family.c +++ b/hw/bsp/stm32f0/family.c @@ -24,8 +24,9 @@ * This file is part of the TinyUSB stack. */ -#include "../board.h" #include "stm32f0xx_hal.h" +#include "bsp/board.h" +#include "board.h" //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler @@ -38,79 +39,28 @@ void USB_IRQHandler(void) //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ -#define LED_PORT GPIOC -#define LED_PIN GPIO_PIN_6 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOA -#define BUTTON_PIN GPIO_PIN_0 -#define BUTTON_STATE_ACTIVE 1 - -#define UARTx USART1 -#define UART_GPIO_PORT GPIOA -#define UART_GPIO_AF GPIO_AF1_USART1 -#define UART_TX_PIN GPIO_PIN_9 -#define UART_RX_PIN GPIO_PIN_10 - UART_HandleTypeDef UartHandle; - -// enable all LED, Button, Uart, USB clock -static void all_rcc_clk_enable(void) -{ - __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- - __HAL_RCC_GPIOC_CLK_ENABLE(); // LED - //__HAL_RCC_GPIOA_CLK_ENABLE(); // Button - //__HAL_RCC_GPIOA_CLK_ENABLE(); // Uart tx, rx - __HAL_RCC_USART1_CLK_ENABLE(); // Uart module -} - -/** - * @brief System Clock Configuration - * The system Clock is configured as follow : - * System Clock source = PLL (HSI48) - * SYSCLK(Hz) = 48000000 - * HCLK(Hz) = 48000000 - * AHB Prescaler = 1 - * APB1 Prescaler = 1 - * HSI Frequency(Hz) = 48000000 - * PREDIV = 2 - * PLLMUL = 2 - * Flash Latency(WS) = 1 - * @param None - * @retval None - */ -static void SystemClock_Config(void) -{ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - - /* Select HSI48 Oscillator as PLL source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48; - RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI48; - RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2; - RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL2; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Select PLL as system clock source and configure the HCLK and PCLK1 clocks dividers */ - RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1); - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); -} - void board_init(void) { - SystemClock_Config(); - all_rcc_clk_enable(); + board_stm32f0_clock_init(); + + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOF_CLK_ENABLE(); + + // Enable UART Clock + UART_CLK_EN(); - #if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer SysTick_Config(SystemCoreClock / 1000); - #endif + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif // LED GPIO_InitTypeDef GPIO_InitStruct; @@ -135,7 +85,7 @@ void board_init(void) GPIO_InitStruct.Alternate = UART_GPIO_AF; HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); - UartHandle.Instance = UARTx; + UartHandle.Instance = UART_DEV; UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; UartHandle.Init.WordLength = UART_WORDLENGTH_8B; UartHandle.Init.StopBits = UART_STOPBITS_1; diff --git a/hw/bsp/stm32f070rbnucleo/board.mk b/hw/bsp/stm32f070rbnucleo/board.mk deleted file mode 100644 index 78dd0a39a..000000000 --- a/hw/bsp/stm32f070rbnucleo/board.mk +++ /dev/null @@ -1,51 +0,0 @@ -ST_FAMILY = f0 -DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) -ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs-linux \ - -mcpu=cortex-m0 \ - -mfloat-abi=soft \ - -nostdlib -nostartfiles \ - -DSTM32F070xB \ - -DCFG_EXAMPLE_MSC_READONLY \ - -DCFG_TUSB_MCU=OPT_MCU_STM32F0 - -# suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=unused-parameter -Wno-error=cast-align - - -# All source paths should be relative to the top level. -LD_FILE = hw/bsp/$(BOARD)/stm32F070rbtx_flash.ld - -SRC_C += \ - src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \ - $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c - -SRC_S += \ - $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f070xb.s - -INC += \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(ST_CMSIS)/Include \ - $(TOP)/$(ST_HAL_DRIVER)/Inc \ - $(TOP)/hw/bsp/$(BOARD) - -# For freeRTOS port source -FREERTOS_PORT = ARM_CM0 - -# For flash-jlink target -JLINK_DEVICE = stm32f070rb - -# flash target using on-board stlink -flash: flash-stlink diff --git a/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c b/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c deleted file mode 100644 index ded5a9c85..000000000 --- a/hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c +++ /dev/null @@ -1,204 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "../board.h" -#include "stm32f0xx_hal.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB_IRQHandler(void) -{ - tud_int_handler(0); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ -#define LED_PORT GPIOA -#define LED_PIN GPIO_PIN_5 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOC -#define BUTTON_PIN GPIO_PIN_13 -#define BUTTON_STATE_ACTIVE 0 - -#define UARTx USART2 -#define UART_GPIO_PORT GPIOA -#define UART_GPIO_AF GPIO_AF1_USART2 -#define UART_TX_PIN GPIO_PIN_2 -#define UART_RX_PIN GPIO_PIN_3 - -UART_HandleTypeDef UartHandle; - - // enable all LED, Button, Uart, USB clock -static void all_rcc_clk_enable(void) -{ - __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- - __HAL_RCC_GPIOC_CLK_ENABLE(); // LED - //__HAL_RCC_GPIOA_CLK_ENABLE(); // Button - //__HAL_RCC_GPIOA_CLK_ENABLE(); // Uart tx, rx - __HAL_RCC_USART2_CLK_ENABLE(); // Uart module -} - -void board_init(void) -{ - /* Configure the system clock to 48 MHz */ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; - - /* Enable HSE Oscillator and activate PLL with 8 MHz HSE as source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6; - RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 - clocks dividers */ - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1; - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; - (void) HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); - - - PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB; - PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL; - (void)HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) ; - - // Notify runtime of frequency change. - all_rcc_clk_enable(); - - #if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - #endif - - // LED - GPIO_InitTypeDef GPIO_InitStruct; - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); - - // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_PULLDOWN; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - - // Uart - GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = UART_GPIO_AF; - HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); - - UartHandle.Instance = UARTx; - UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; - UartHandle.Init.WordLength = UART_WORDLENGTH_8B; - UartHandle.Init.StopBits = UART_STOPBITS_1; - UartHandle.Init.Parity = UART_PARITY_NONE; - UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; - UartHandle.Init.Mode = UART_MODE_TX_RX; - UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; - HAL_UART_Init(&UartHandle); - - // Start USB clock - __HAL_RCC_USB_CLK_ENABLE(); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - -void HardFault_Handler (void) -{ - asm("bkpt"); -} - -#ifdef USE_FULL_ASSERT -/** - * @brief Reports the name of the source file and the source line number - * where the assert_param error has occurred. - * @param file: pointer to the source file name - * @param line: assert_param error line source number - * @retval None - */ -void assert_failed(uint8_t* file, uint32_t line) -{ - TU_LOG1("Assertion failed (%s:%ld)\r\n", file, line); -} -#endif /* USE_FULL_ASSERT */ - -// Required by __libc_init_array in startup code if we are compiling using -// -nostdlib/-nostartfiles. -void _init(void) -{ - -} diff --git a/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h b/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h deleted file mode 100644 index cfa66b366..000000000 --- a/hw/bsp/stm32f070rbnucleo/stm32f0xx_hal_conf.h +++ /dev/null @@ -1,321 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f0xx_hal_conf.h - * @author MCD Application Team - * @brief HAL configuration file. - ****************************************************************************** - * @attention - * - *

© Copyright (c) 2016 STMicroelectronics. - * All rights reserved.

- * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F0xx_HAL_CONF_H -#define __STM32F0xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -/*#define HAL_ADC_MODULE_ENABLED */ -/*#define HAL_CAN_MODULE_ENABLED */ -/*#define HAL_CEC_MODULE_ENABLED */ -/*#define HAL_COMP_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -/*#define HAL_CRC_MODULE_ENABLED */ -/*#define HAL_DAC_MODULE_ENABLED */ -#define HAL_DMA_MODULE_ENABLED -#define HAL_FLASH_MODULE_ENABLED -#define HAL_GPIO_MODULE_ENABLED -/*#define HAL_EXTI_MODULE_ENABLED */ -/*#define HAL_I2C_MODULE_ENABLED */ -/*#define HAL_I2S_MODULE_ENABLED */ -/*#define HAL_IRDA_MODULE_ENABLED */ -/*#define HAL_IWDG_MODULE_ENABLED */ -#define HAL_PCD_MODULE_ENABLED -#define HAL_PWR_MODULE_ENABLED -#define HAL_RCC_MODULE_ENABLED -/*#define HAL_RTC_MODULE_ENABLED */ -/*#define HAL_SMARTCARD_MODULE_ENABLED */ -/*#define HAL_SMBUS_MODULE_ENABLED */ -/*#define HAL_SPI_MODULE_ENABLED */ -/*#define HAL_TIM_MODULE_ENABLED */ -/*#define HAL_TSC_MODULE_ENABLED */ -#define HAL_UART_MODULE_ENABLED -/*#define HAL_USART_MODULE_ENABLED */ -/*#define HAL_WWDG_MODULE_ENABLED */ - -/* ######################### Oscillator Values adaptation ################### */ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -/** - * @brief In the following line adjust the External High Speed oscillator (HSE) Startup - * Timeout value - */ -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup - * Timeout value - */ -#if !defined (HSI_STARTUP_TIMEOUT) - #define HSI_STARTUP_TIMEOUT 5000U /*!< Time out for HSI start up */ -#endif /* HSI_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator for ADC (HSI14) value. - */ -#if !defined (HSI14_VALUE) - #define HSI14_VALUE 14000000U /*!< Value of the Internal High Speed oscillator for ADC in Hz. - The real value may vary depending on the variations - in voltage and temperature. */ -#endif /* HSI14_VALUE */ - -/** - * @brief Internal High Speed oscillator for USB (HSI48) value. - */ -#if !defined (HSI48_VALUE) - #define HSI48_VALUE 48000000U /*!< Value of the Internal High Speed oscillator for USB in Hz. - The real value may vary depending on the variations - in voltage and temperature. */ -#endif /* HSI48_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE 32000U -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature. */ -/** - * @brief External Low Speed oscillator (LSE) value. - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ -#endif /* LSE_VALUE */ - -/** - * @brief Time out for LSE start up value in ms. - */ -#if !defined (LSE_STARTUP_TIMEOUT) - #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ -#endif /* LSE_STARTUP_TIMEOUT */ - - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE 3300U /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY ((uint32_t)(1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority (lowest by default) */ - /* Warning: Must be set to higher priority for HAL_Delay() */ - /* and HAL_GetTick() usage under interrupt context */ -#define USE_RTOS 0U -#define PREFETCH_ENABLE 1U -#define INSTRUCTION_CACHE_ENABLE 0U -#define DATA_CACHE_ENABLE 0U -#define USE_SPI_CRC 1U - -#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ -#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ -#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */ -#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ -#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ -#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ -#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ -#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ -#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ -#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ -#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ -#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ -#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ -#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ -#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ -#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ -#define USE_HAL_TSC_REGISTER_CALLBACKS 0U /* TSC register callback disabled */ -#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ - #define USE_FULL_ASSERT 1 - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32f0xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32f0xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_EXTI_MODULE_ENABLED - #include "stm32f0xx_hal_exti.h" -#endif /* HAL_EXTI_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32f0xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32f0xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32f0xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32f0xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CEC_MODULE_ENABLED - #include "stm32f0xx_hal_cec.h" -#endif /* HAL_CEC_MODULE_ENABLED */ - -#ifdef HAL_COMP_MODULE_ENABLED - #include "stm32f0xx_hal_comp.h" -#endif /* HAL_COMP_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32f0xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32f0xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32f0xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32f0xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32f0xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32f0xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32f0xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32f0xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32f0xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32f0xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32f0xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_SMBUS_MODULE_ENABLED - #include "stm32f0xx_hal_smbus.h" -#endif /* HAL_SMBUS_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32f0xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32f0xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_TSC_MODULE_ENABLED - #include "stm32f0xx_hal_tsc.h" -#endif /* HAL_TSC_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32f0xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32f0xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32f0xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t* file, uint32_t line); -#else - #define assert_param(expr) ((void)0U) -#endif /* USE_FULL_ASSERT */ - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F0xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -