diff --git a/hw/bsp/imxrt/boards/mimxrt1024_evk/board.h b/hw/bsp/imxrt/boards/mimxrt1024_evk/board.h new file mode 100644 index 000000000..152c9ab18 --- /dev/null +++ b/hw/bsp/imxrt/boards/mimxrt1024_evk/board.h @@ -0,0 +1,52 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + + +#ifndef BOARD_H_ +#define BOARD_H_ + +// required since iMX RT10xx SDK include this file for board size +// RT1020-EVK #define BOARD_FLASH_SIZE (0x800000U) +#define BOARD_FLASH_SIZE (0x400000U) // builtin flash of RT1024 + +// LED - DRN updated for RT1024EVK +#define LED_PINMUX IOMUXC_GPIO_AD_B1_08_GPIO1_IO24 +#define LED_PORT GPIO1 +#define LED_PIN 24 +#define LED_STATE_ON 1 + +// SW8 button - DRN verified +#define BUTTON_PINMUX IOMUXC_SNVS_WAKEUP_GPIO5_IO00 +#define BUTTON_PORT GPIO5 +#define BUTTON_PIN 0 +#define BUTTON_STATE_ACTIVE 0 + +// UART - DRN verified +#define UART_PORT LPUART1 +#define UART_RX_PINMUX IOMUXC_GPIO_AD_B0_07_LPUART1_RX +#define UART_TX_PINMUX IOMUXC_GPIO_AD_B0_06_LPUART1_TX + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/imxrt/boards/mimxrt1024_evk/board.mk b/hw/bsp/imxrt/boards/mimxrt1024_evk/board.mk new file mode 100644 index 000000000..92209992d --- /dev/null +++ b/hw/bsp/imxrt/boards/mimxrt1024_evk/board.mk @@ -0,0 +1,14 @@ +CFLAGS += -DCPU_MIMXRT1024DAG5A +MCU_VARIANT = MIMXRT1024 + +# warnings caused by mcu driver +CFLAGS += -Wno-error=array-bounds + +# For flash-jlink target +JLINK_DEVICE = MIMXRT1024DAG5A + +# For flash-pyocd target +PYOCD_TARGET = mimxrt1024 + +# flash using pyocd +flash: flash-pyocd diff --git a/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.c b/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.c new file mode 100644 index 000000000..43dc1e823 --- /dev/null +++ b/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.c @@ -0,0 +1,48 @@ +/* + * Copyright 2020 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#include "evkmimxrt1024_flexspi_nor_config.h" + +/* Component ID definition, used by tools. */ +#ifndef FSL_COMPONENT_ID +#define FSL_COMPONENT_ID "platform.drivers.xip_board" +#endif + +/******************************************************************************* + * Code + ******************************************************************************/ +#if defined(XIP_BOOT_HEADER_ENABLE) && (XIP_BOOT_HEADER_ENABLE == 1) +#if defined(__CC_ARM) || defined(__ARMCC_VERSION) || defined(__GNUC__) +__attribute__((section(".boot_hdr.conf"), used)) +#elif defined(__ICCARM__) +#pragma location = ".boot_hdr.conf" +#endif + +const flexspi_nor_config_t qspiflash_config = { + .memConfig = + { + .tag = FLEXSPI_CFG_BLK_TAG, + .version = FLEXSPI_CFG_BLK_VERSION, + .readSampleClkSrc = kFlexSPIReadSampleClk_LoopbackInternally, + .csHoldTime = 3u, + .csSetupTime = 3u, + .sflashPadType = kSerialFlash_4Pads, + .serialClkFreq = kFlexSpiSerialClk_60MHz, + .sflashA1Size = 4u * 1024u * 1024u, + .lookupTable = + { + // Read LUTs + FLEXSPI_LUT_SEQ(CMD_SDR, FLEXSPI_1PAD, 0xEB, RADDR_SDR, FLEXSPI_4PAD, 0x18), + FLEXSPI_LUT_SEQ(DUMMY_SDR, FLEXSPI_4PAD, 0x06, READ_SDR, FLEXSPI_4PAD, 0x04), + }, + }, + .pageSize = 256u, + .sectorSize = 4u * 1024u, + .blockSize = 64u * 1024u, + .isUniformBlockSize = false, +}; +#endif /* XIP_BOOT_HEADER_ENABLE */ diff --git a/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.h b/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.h new file mode 100644 index 000000000..5231dc034 --- /dev/null +++ b/hw/bsp/imxrt/boards/mimxrt1024_evk/evkmimxrt1024_flexspi_nor_config.h @@ -0,0 +1,266 @@ +/* + * Copyright 2020 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef __EVKMIMXRT1024_FLEXSPI_NOR_CONFIG__ +#define __EVKMIMXRT1024_FLEXSPI_NOR_CONFIG__ + +#include +#include +#include "fsl_common.h" + +/*! @name Driver version */ +/*@{*/ +/*! @brief XIP_BOARD driver version 2.0.1. */ +#define FSL_XIP_BOARD_DRIVER_VERSION (MAKE_VERSION(2, 0, 1)) +/*@}*/ + +/* FLEXSPI memory config block related definitions */ +#define FLEXSPI_CFG_BLK_TAG (0x42464346UL) // ascii "FCFB" Big Endian +#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0 +#define FLEXSPI_CFG_BLK_SIZE (512) + +/* FLEXSPI Feature related definitions */ +#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1 + +/* Lookup table related definitions */ +#define CMD_INDEX_READ 0 +#define CMD_INDEX_READSTATUS 1 +#define CMD_INDEX_WRITEENABLE 2 +#define CMD_INDEX_WRITE 4 + +#define CMD_LUT_SEQ_IDX_READ 0 +#define CMD_LUT_SEQ_IDX_READSTATUS 1 +#define CMD_LUT_SEQ_IDX_WRITEENABLE 3 +#define CMD_LUT_SEQ_IDX_WRITE 9 + +#define CMD_SDR 0x01 +#define CMD_DDR 0x21 +#define RADDR_SDR 0x02 +#define RADDR_DDR 0x22 +#define CADDR_SDR 0x03 +#define CADDR_DDR 0x23 +#define MODE1_SDR 0x04 +#define MODE1_DDR 0x24 +#define MODE2_SDR 0x05 +#define MODE2_DDR 0x25 +#define MODE4_SDR 0x06 +#define MODE4_DDR 0x26 +#define MODE8_SDR 0x07 +#define MODE8_DDR 0x27 +#define WRITE_SDR 0x08 +#define WRITE_DDR 0x28 +#define READ_SDR 0x09 +#define READ_DDR 0x29 +#define LEARN_SDR 0x0A +#define LEARN_DDR 0x2A +#define DATSZ_SDR 0x0B +#define DATSZ_DDR 0x2B +#define DUMMY_SDR 0x0C +#define DUMMY_DDR 0x2C +#define DUMMY_RWDS_SDR 0x0D +#define DUMMY_RWDS_DDR 0x2D +#define JMP_ON_CS 0x1F +#define STOP 0 + +#define FLEXSPI_1PAD 0 +#define FLEXSPI_2PAD 1 +#define FLEXSPI_4PAD 2 +#define FLEXSPI_8PAD 3 + +#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1) \ + (FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \ + FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1)) + +//!@brief Definitions for FlexSPI Serial Clock Frequency +typedef enum _FlexSpiSerialClockFreq +{ + kFlexSpiSerialClk_30MHz = 1, + kFlexSpiSerialClk_50MHz = 2, + kFlexSpiSerialClk_60MHz = 3, + kFlexSpiSerialClk_75MHz = 4, + kFlexSpiSerialClk_80MHz = 5, + kFlexSpiSerialClk_100MHz = 6, + kFlexSpiSerialClk_133MHz = 7, +} flexspi_serial_clk_freq_t; + +//!@brief FlexSPI clock configuration type +enum +{ + kFlexSpiClk_SDR, //!< Clock configure for SDR mode + kFlexSpiClk_DDR, //!< Clock configurat for DDR mode +}; + +//!@brief FlexSPI Read Sample Clock Source definition +typedef enum _FlashReadSampleClkSource +{ + kFlexSPIReadSampleClk_LoopbackInternally = 0, + kFlexSPIReadSampleClk_LoopbackFromDqsPad = 1, + kFlexSPIReadSampleClk_LoopbackFromSckPad = 2, + kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3, +} flexspi_read_sample_clk_t; + +//!@brief Misc feature bit definitions +enum +{ + kFlexSpiMiscOffset_DiffClkEnable = 0, //!< Bit for Differential clock enable + kFlexSpiMiscOffset_Ck2Enable = 1, //!< Bit for CK2 enable + kFlexSpiMiscOffset_ParallelEnable = 2, //!< Bit for Parallel mode enable + kFlexSpiMiscOffset_WordAddressableEnable = 3, //!< Bit for Word Addressable enable + kFlexSpiMiscOffset_SafeConfigFreqEnable = 4, //!< Bit for Safe Configuration Frequency enable + kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, //!< Bit for Pad setting override enable + kFlexSpiMiscOffset_DdrModeEnable = 6, //!< Bit for DDR clock confiuration indication. +}; + +//!@brief Flash Type Definition +enum +{ + kFlexSpiDeviceType_SerialNOR = 1, //!< Flash devices are Serial NOR + kFlexSpiDeviceType_SerialNAND = 2, //!< Flash devices are Serial NAND + kFlexSpiDeviceType_SerialRAM = 3, //!< Flash devices are Serial RAM/HyperFLASH + kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, //!< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND + kFlexSpiDeviceType_MCP_NOR_RAM = 0x13, //!< Flash device is MCP device, A1 is Serial NOR, A2 is Serial RAMs +}; + +//!@brief Flash Pad Definitions +enum +{ + kSerialFlash_1Pad = 1, + kSerialFlash_2Pads = 2, + kSerialFlash_4Pads = 4, + kSerialFlash_8Pads = 8, +}; + +//!@brief FlexSPI LUT Sequence structure +typedef struct _lut_sequence +{ + uint8_t seqNum; //!< Sequence Number, valid number: 1-16 + uint8_t seqId; //!< Sequence Index, valid number: 0-15 + uint16_t reserved; +} flexspi_lut_seq_t; + +//!@brief Flash Configuration Command Type +enum +{ + kDeviceConfigCmdType_Generic, //!< Generic command, for example: configure dummy cycles, drive strength, etc + kDeviceConfigCmdType_QuadEnable, //!< Quad Enable command + kDeviceConfigCmdType_Spi2Xpi, //!< Switch from SPI to DPI/QPI/OPI mode + kDeviceConfigCmdType_Xpi2Spi, //!< Switch from DPI/QPI/OPI to SPI mode + kDeviceConfigCmdType_Spi2NoCmd, //!< Switch to 0-4-4/0-8-8 mode + kDeviceConfigCmdType_Reset, //!< Reset device command +}; + +//!@brief FlexSPI Memory Configuration Block +typedef struct _FlexSPIConfig +{ + uint32_t tag; //!< [0x000-0x003] Tag, fixed value 0x42464346UL + uint32_t version; //!< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix + uint32_t reserved0; //!< [0x008-0x00b] Reserved for future use + uint8_t readSampleClkSrc; //!< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3 + uint8_t csHoldTime; //!< [0x00d-0x00d] CS hold time, default value: 3 + uint8_t csSetupTime; //!< [0x00e-0x00e] CS setup time, default value: 3 + uint8_t columnAddressWidth; //!< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For + //! Serial NAND, need to refer to datasheet + uint8_t deviceModeCfgEnable; //!< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable + uint8_t deviceModeType; //!< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch, + //! Generic configuration, etc. + uint16_t waitTimeCfgCommands; //!< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for + //! DPI/QPI/OPI switch or reset command + flexspi_lut_seq_t deviceModeSeq; //!< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt + //! sequence number, [31:16] Reserved + uint32_t deviceModeArg; //!< [0x018-0x01b] Argument/Parameter for device configuration + uint8_t configCmdEnable; //!< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable + uint8_t configModeType[3]; //!< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe + flexspi_lut_seq_t + configCmdSeqs[3]; //!< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq + uint32_t reserved1; //!< [0x02c-0x02f] Reserved for future use + uint32_t configCmdArgs[3]; //!< [0x030-0x03b] Arguments/Parameters for device Configuration commands + uint32_t reserved2; //!< [0x03c-0x03f] Reserved for future use + uint32_t controllerMiscOption; //!< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more + //! details + uint8_t deviceType; //!< [0x044-0x044] Device Type: See Flash Type Definition for more details + uint8_t sflashPadType; //!< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal + uint8_t serialClkFreq; //!< [0x046-0x046] Serial Flash Frequency, device specific definitions, See System Boot + //! Chapter for more details + uint8_t lutCustomSeqEnable; //!< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot + //! be done using 1 LUT sequence, currently, only applicable to HyperFLASH + uint32_t reserved3[2]; //!< [0x048-0x04f] Reserved for future use + uint32_t sflashA1Size; //!< [0x050-0x053] Size of Flash connected to A1 + uint32_t sflashA2Size; //!< [0x054-0x057] Size of Flash connected to A2 + uint32_t sflashB1Size; //!< [0x058-0x05b] Size of Flash connected to B1 + uint32_t sflashB2Size; //!< [0x05c-0x05f] Size of Flash connected to B2 + uint32_t csPadSettingOverride; //!< [0x060-0x063] CS pad setting override value + uint32_t sclkPadSettingOverride; //!< [0x064-0x067] SCK pad setting override value + uint32_t dataPadSettingOverride; //!< [0x068-0x06b] data pad setting override value + uint32_t dqsPadSettingOverride; //!< [0x06c-0x06f] DQS pad setting override value + uint32_t timeoutInMs; //!< [0x070-0x073] Timeout threshold for read status command + uint32_t commandInterval; //!< [0x074-0x077] CS deselect interval between two commands + uint16_t dataValidTime[2]; //!< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns + uint16_t busyOffset; //!< [0x07c-0x07d] Busy offset, valid value: 0-31 + uint16_t busyBitPolarity; //!< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 - + //! busy flag is 0 when flash device is busy + uint32_t lookupTable[64]; //!< [0x080-0x17f] Lookup table holds Flash command sequences + flexspi_lut_seq_t lutCustomSeq[12]; //!< [0x180-0x1af] Customizable LUT Sequences + uint32_t reserved4[4]; //!< [0x1b0-0x1bf] Reserved for future use +} flexspi_mem_config_t; + +/* */ +#define NOR_CMD_INDEX_READ CMD_INDEX_READ //!< 0 +#define NOR_CMD_INDEX_READSTATUS CMD_INDEX_READSTATUS //!< 1 +#define NOR_CMD_INDEX_WRITEENABLE CMD_INDEX_WRITEENABLE //!< 2 +#define NOR_CMD_INDEX_ERASESECTOR 3 //!< 3 +#define NOR_CMD_INDEX_PAGEPROGRAM CMD_INDEX_WRITE //!< 4 +#define NOR_CMD_INDEX_CHIPERASE 5 //!< 5 +#define NOR_CMD_INDEX_DUMMY 6 //!< 6 +#define NOR_CMD_INDEX_ERASEBLOCK 7 //!< 7 + +#define NOR_CMD_LUT_SEQ_IDX_READ CMD_LUT_SEQ_IDX_READ //!< 0 READ LUT sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_READSTATUS \ + CMD_LUT_SEQ_IDX_READSTATUS //!< 1 Read Status LUT sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI \ + 2 //!< 2 Read status DPI/QPI/OPI sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE \ + CMD_LUT_SEQ_IDX_WRITEENABLE //!< 3 Write Enable sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI \ + 4 //!< 4 Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5 //!< 5 Erase Sector sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK 8 //!< 8 Erase Block sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM \ + CMD_LUT_SEQ_IDX_WRITE //!< 9 Program sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11 //!< 11 Chip Erase sequence in lookupTable id stored in config block +#define NOR_CMD_LUT_SEQ_IDX_READ_SFDP 13 //!< 13 Read SFDP sequence in lookupTable id stored in config block +#define NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD \ + 14 //!< 14 Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block +#define NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD \ + 15 //!< 15 Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config blobk + +/* + * Serial NOR configuration block + */ +typedef struct _flexspi_nor_config +{ + flexspi_mem_config_t memConfig; //!< Common memory configuration info via FlexSPI + uint32_t pageSize; //!< Page size of Serial NOR + uint32_t sectorSize; //!< Sector size of Serial NOR + uint8_t ipcmdSerialClkFreq; //!< Clock frequency for IP command + uint8_t isUniformBlockSize; //!< Sector/Block size is the same + uint8_t reserved0[2]; //!< Reserved for future use + uint8_t serialNorType; //!< Serial NOR Flash type: 0/1/2/3 + uint8_t needExitNoCmdMode; //!< Need to exit NoCmd mode before other IP command + uint8_t halfClkForNonReadCmd; //!< Half the Serial Clock for non-read command: true/false + uint8_t needRestoreNoCmdMode; //!< Need to Restore NoCmd mode after IP command execution + uint32_t blockSize; //!< Block size + uint32_t reserve2[11]; //!< Reserved for future use +} flexspi_nor_config_t; + +#ifdef __cplusplus +extern "C" { +#endif + +#ifdef __cplusplus +} +#endif +#endif /* __EVKMIMXRT1024_FLEXSPI_NOR_CONFIG__ */ diff --git a/hw/bsp/stm32h7/boards/stm32h723nucleo/board.h b/hw/bsp/stm32h7/boards/stm32h723nucleo/board.h new file mode 100644 index 000000000..56a48ec24 --- /dev/null +++ b/hw/bsp/stm32h7/boards/stm32h723nucleo/board.h @@ -0,0 +1,131 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_0 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 1 + +#define UART_DEV USART3 +#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE +#define UART_GPIO_PORT GPIOD +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_8 +#define UART_RX_PIN GPIO_PIN_9 + +// VBUS Sense detection +#define OTG_FS_VBUS_SENSE 1 +#define OTG_HS_VBUS_SENSE 0 + +// STM32F723 has only one USB HS peripheral +// Nucleo board does not have ULPI so USB will operate in FS mode only +// For the rest of the synopsys driver it is FS device however there +// is only USB_OTG_HS defined. Here are required conversions to +// make peripheral FS. +#define __HAL_RCC_USB2_OTG_FS_CLK_ENABLE __HAL_RCC_USB1_OTG_HS_CLK_ENABLE +#define GPIO_AF10_OTG2_HS GPIO_AF10_OTG1_HS +#define USB_OTG_FS USB_OTG_HS + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32h7_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* The PWR block is always enabled on the H7 series- there is no clock + enable. For now, use the default VOS3 scale mode (lowest) and limit clock + frequencies to avoid potential current draw problems from bus + power when using the max clock speeds throughout the chip. */ + + /* Enable HSE Oscillator and activate PLL1 with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSIState = RCC_HSI_OFF; + RCC_OscInitStruct.CSIState = RCC_CSI_OFF; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 336; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLQ = 7; + RCC_OscInitStruct.PLL.PLLR = 2; /* Unused */ + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_0; + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | \ + RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | \ + RCC_CLOCKTYPE_D3PCLK1); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1; + + /* Unlike on the STM32F4 family, it appears the maximum APB frequencies are + device-dependent- 120 MHz for this board according to Figure 2 of + the datasheet. Dividing by half will be safe for now. */ + RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; + RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2; + + /* 4 wait states required for 168MHz and VOS3. */ + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); + + /* Like on F4, on H7, USB's actual peripheral clock and bus clock are + separate. However, the main system PLL (PLL1) doesn't have a direct + connection to the USB peripheral clock to generate 48 MHz, so we do this + dance. This will connect PLL1's Q output to the USB peripheral clock. */ + RCC_PeriphCLKInitTypeDef RCC_PeriphCLKInitStruct; + + RCC_PeriphCLKInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + RCC_PeriphCLKInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL; + HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphCLKInitStruct); +} + +static inline void board_stm32h7_post_init(void) +{ + // For this board does nothing +} + + +#ifdef __cplusplus + } +#endif + +#endif diff --git a/hw/bsp/stm32h7/boards/stm32h723nucleo/board.mk b/hw/bsp/stm32h7/boards/stm32h723nucleo/board.mk new file mode 100644 index 000000000..bbd0a0e58 --- /dev/null +++ b/hw/bsp/stm32h7/boards/stm32h723nucleo/board.mk @@ -0,0 +1,13 @@ +CFLAGS += -DSTM32H723xx -DHSE_VALUE=8000000 + +# Default is FulSpeed port +PORT ?= 0 + +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h723xx.s +LD_FILE = $(BOARD_PATH)/stm32h723xx_flash.ld + +# For flash-jlink target +JLINK_DEVICE = stm32h723zg + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32h7/boards/stm32h723nucleo/stm32h723xx_flash.ld b/hw/bsp/stm32h7/boards/stm32h723nucleo/stm32h723xx_flash.ld new file mode 100644 index 000000000..05e0d4e26 --- /dev/null +++ b/hw/bsp/stm32h7/boards/stm32h723nucleo/stm32h723xx_flash.ld @@ -0,0 +1,192 @@ +/* +****************************************************************************** +** +** File : LinkerScript.ld +** +** Author : STM32CubeIDE +** +** Abstract : Linker script for STM32H7 series +** 1024Kbytes FLASH and 560Kbytes RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** Copyright (c) 2021 STMicroelectronics. +** All rights reserved. +** +** This software is licensed under terms that can be found in the LICENSE file +** in the root directory of this software component. +** If no LICENSE file comes with this software, it is provided AS-IS. +** +**************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = ORIGIN(RAM_D1) + LENGTH(RAM_D1); /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200 ; /* required amount of heap */ +_Min_Stack_Size = 0x400 ; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ + ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K + DTCMRAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K + FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K + RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 320K + RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 32K + RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 16K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + *(.RamFunc) /* .RamFunc sections */ + *(.RamFunc*) /* .RamFunc* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM_D1 AT> FLASH + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM_D1 + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM_D1 + + .usbx_data 0x24027000 (NOLOAD): + { + *(.UsbHpcdSection) + + } >RAM_D1 + + .uart_bss 0x24028000 (NOLOAD): + { + *(.UsbxAppSection) + + } >RAM_D1 + + .usbx_bss 0x24029000 (NOLOAD): + { + *(.UsbxPoolSection) + + } >RAM_D1 + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32h7/family.c b/hw/bsp/stm32h7/family.c index 3964f427a..0aa8fe47f 100644 --- a/hw/bsp/stm32h7/family.c +++ b/hw/bsp/stm32h7/family.c @@ -66,10 +66,12 @@ void board_init(void) __HAL_RCC_GPIOC_CLK_ENABLE(); // USB ULPI NXT __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOE_CLK_ENABLE(); - __HAL_RCC_GPIOE_CLK_ENABLE(); + __HAL_RCC_GPIOF_CLK_ENABLE(); __HAL_RCC_GPIOG_CLK_ENABLE(); __HAL_RCC_GPIOH_CLK_ENABLE(); // USB ULPI NXT +#ifdef __HAL_RCC_GPIOI_CLK_ENABLE __HAL_RCC_GPIOI_CLK_ENABLE(); // USB ULPI NXT +#endif __HAL_RCC_GPIOJ_CLK_ENABLE(); // Enable UART Clock @@ -84,7 +86,9 @@ void board_init(void) SysTick->CTRL &= ~1U; // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) +#ifdef USB_OTG_FS_PERIPH_BASE NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); #endif diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index b53735a5e..c6132a1f5 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -529,8 +529,10 @@ void dcd_init (uint8_t rhport) dwc2->dcfg |= DCFG_NZLSOHSK; // Clear all interrupts - dwc2->gintsts |= dwc2->gintsts; - dwc2->gotgint |= dwc2->gotgint; + uint32_t int_mask = dwc2->gintsts; + dwc2->gintsts |= int_mask; + int_mask = dwc2->gotgint; + dwc2->gotgint |= int_mask; // Required as part of core initialization. // TODO: How should mode mismatch be handled? It will cause @@ -1219,7 +1221,8 @@ void dcd_int_handler(uint8_t rhport) { dwc2_regs_t *dwc2 = DWC2_REG(rhport); - uint32_t const int_status = dwc2->gintsts & dwc2->gintmsk; + uint32_t const int_mask = dwc2->gintmsk; + uint32_t const int_status = dwc2->gintsts & int_mask; if(int_status & GINTSTS_USBRST) { diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index b63d1fcd0..cb455bd90 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -122,13 +122,13 @@ static const dwc2_controller_t _dwc2_controller[] = TU_ATTR_ALWAYS_INLINE static inline void dwc2_dcd_int_enable(uint8_t rhport) { - NVIC_EnableIRQ(_dwc2_controller[rhport].irqnum); + NVIC_EnableIRQ((IRQn_Type)_dwc2_controller[rhport].irqnum); } TU_ATTR_ALWAYS_INLINE static inline void dwc2_dcd_int_disable (uint8_t rhport) { - NVIC_DisableIRQ(_dwc2_controller[rhport].irqnum); + NVIC_DisableIRQ((IRQn_Type)_dwc2_controller[rhport].irqnum); } TU_ATTR_ALWAYS_INLINE diff --git a/test/fuzz/device/cdc/cdc_seed_corpus.zip b/test/fuzz/device/cdc/cdc_seed_corpus.zip new file mode 100644 index 000000000..81bc2240d Binary files /dev/null and b/test/fuzz/device/cdc/cdc_seed_corpus.zip differ diff --git a/test/fuzz/device/msc/msc_seed_corpus.zip b/test/fuzz/device/msc/msc_seed_corpus.zip new file mode 100644 index 000000000..81bc2240d Binary files /dev/null and b/test/fuzz/device/msc/msc_seed_corpus.zip differ diff --git a/tools/pcapng_to_corpus.py b/tools/pcapng_to_corpus.py new file mode 100755 index 000000000..78b1f77a2 --- /dev/null +++ b/tools/pcapng_to_corpus.py @@ -0,0 +1,46 @@ +#!/bin/python3 +import argparse +import pcapng +import zipfile +import hashlib + +def extract_packets(pcap_file): + """Reads a wireshark packet capture and extracts the binary packets""" + packets = [] + with open(pcap_file, 'rb') as fp: + scanner = pcapng.FileScanner(fp) + for block in scanner: + if isinstance(block, pcapng.blocks.EnhancedPacket): + packets.append(block.packet_data) + return packets + +def build_corpus_zip(zip_file_output, packets): + """Builds a zip file with a file per packet + + The structure of this zip corpus is a simple content addressable storage + i.e. seed_file_name == sha256_digest(packet). + """ + with zipfile.ZipFile(zip_file_output, 'a') as out: + for packet in packets: + hash = hashlib.sha256(packet).hexdigest() + if hash not in out.namelist(): + out.writestr(hash, packet) + + +def main(pcap_file, output_zip_file): + packets = extract_packets(pcap_file) + build_corpus_zip(output_zip_file, packets) + +if __name__ == "__main__": + parser = argparse.ArgumentParser( + prog = "pcapng_to_corpus.py", + description="""Converts a wireshark capture to a zip of binary packet + files suitable for an oss-fuzz corpus. In the case the + zip corpus already exists, this script will modify + the zip file in place adding seed entries.""") + parser.add_argument('pcapng_capture_file') + parser.add_argument('oss_fuzz_corpus_zip') + args = parser.parse_args() + main(args.pcapng_capture_file, args.oss_fuzz_corpus_zip) + +