add PORT selection for makefile

hw/bsp/ra/boards/ra6m5_ek/board.mk

@@ -4,4 +4,7 @@ MCU_VARIANT = ra6m5
 # For flash-jlink target
 JLINK_DEVICE = R7FA6M5BH
 
+# Port 1 is highspeed
+PORT ?= 1
+
 flash: flash-jlink

hw/bsp/ra/family.cmake

@@ -13,7 +13,7 @@ include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake)
 
 set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake)
 
-set(FAMILY_MCUS RA CACHE INTERNAL "")
+set(FAMILY_MCUS RAXXX CACHE INTERNAL "")
 
 #------------------------------------
 # BOARD_TARGET

hw/bsp/ra/family.mk

@@ -3,8 +3,12 @@ DEPS_SUBMODULES += hw/mcu/renesas/fsp lib/CMSIS_5
 FSP_RA = hw/mcu/renesas/fsp/ra/fsp
 include $(TOP)/$(BOARD_PATH)/board.mk
 
+# Default to port 0 fullspeed, board with port 1 highspeed should override this in board.mk
+PORT ?= 0
+
 CFLAGS += \
   -DCFG_TUSB_MCU=OPT_MCU_RAXXX \
+  -DBOARD_TUD_RHPORT=$(PORT) \
 	-Wno-error=undef \
 	-Wno-error=strict-prototypes \
 	-Wno-error=cast-align \
@@ -15,6 +19,14 @@ CFLAGS += \
 	-nostartfiles \
 	-ffreestanding
 
+ifeq ($(PORT), 1)
+  CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED
+  $(info "Using PORT 1 HighSpeed")
+else
+  CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+  $(info "Using PORT 0 FullSpeed")
+endif
+
 SRC_C += \
 	src/portable/renesas/rusb2/dcd_rusb2.c \
 	src/portable/renesas/rusb2/hcd_rusb2.c \

src/portable/renesas/rusb2/dcd_rusb2.c

@@ -216,6 +216,7 @@ static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo
 
   // Highspeed FIFO is 32-bit
   if ( is_highspeed_regbase(rusb) ) {
+    // TODO 32-bit access for better performance
     ff16 = (volatile uint16_t*) ((uintptr_t) fifo+2);
     ff8  = (volatile uint8_t *) ((uintptr_t) fifo+3);
   }else {
@@ -241,6 +242,9 @@ static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo
 static void pipe_read_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo, unsigned len)
 {
   (void) rusb;
+
+  // TODO 16/32-bit access for better performance
+
   uint8_t *p = (uint8_t*)buf;
   volatile uint8_t *reg = (volatile uint8_t*)fifo;  /* byte access is always at base register address */
   while (len--) *p++ = *reg;