remove TUSB prefix for class enum definitions

add most of HID USAGE TABLE and definitions etc ...

tinyusb/core/std_descriptors.h

@@ -114,7 +114,14 @@ typedef ATTR_PREPACKED struct ATTR_PACKED {
   uint8_t  bDescriptorType  ; ///< ENDPOINT Descriptor Type
 
   uint8_t  bEndpointAddress ; ///< The address of the endpoint on the USB device described by this descriptor. The address is encoded as follows: \n Bit 3...0: The endpoint number \n Bit 6...4: Reserved, reset to zero \n Bit 7: Direction, ignored for control endpoints 0 = OUT endpoint 1 = IN endpoint.
-  uint8_t  bmAttributes     ; ///< This field describes the endpoint's attributes when it is configured using the bConfigurationValue. \n Bits 1..0: Transfer Type \n- 00 = Control \n- 01 = Isochronous \n- 10 = Bulk \n- 11 = Interrupt \n If not an isochronous endpoint, bits 5..2 are reserved and must be set to zero. If isochronous, they are defined as follows: \n Bits 3..2: Synchronization Type \n- 00 = No Synchronization \n- 01 = Asynchronous \n- 10 = Adaptive \n- 11 = Synchronous \n Bits 5..4: Usage Type \n- 00 = Data endpoint \n- 01 = Feedback endpoint \n- 10 = Implicit feedback Data endpoint \n- 11 = Reserved \n Refer to Chapter 5 of USB 2.0 specification for more information. \n All other bits are reserved and must be reset to zero. Reserved bits must be ignored by the host.
+
+  ATTR_PREPACKED struct ATTR_PACKED {
+    uint8_t xfer : 2;
+    uint8_t sync : 2;
+    uint8_t usage : 2;
+    uint8_t : 2;
+  } bmAttributes     ; ///< This field describes the endpoint's attributes when it is configured using the bConfigurationValue. \n Bits 1..0: Transfer Type \n- 00 = Control \n- 01 = Isochronous \n- 10 = Bulk \n- 11 = Interrupt \n If not an isochronous endpoint, bits 5..2 are reserved and must be set to zero. If isochronous, they are defined as follows: \n Bits 3..2: Synchronization Type \n- 00 = No Synchronization \n- 01 = Asynchronous \n- 10 = Adaptive \n- 11 = Synchronous \n Bits 5..4: Usage Type \n- 00 = Data endpoint \n- 01 = Feedback endpoint \n- 10 = Implicit feedback Data endpoint \n- 11 = Reserved \n Refer to Chapter 5 of USB 2.0 specification for more information. \n All other bits are reserved and must be reset to zero. Reserved bits must be ignored by the host.
+
   uint16_t wMaxPacketSize   ; ///< Maximum packet size this endpoint is capable of sending or receiving when this configuration is selected. \n For isochronous endpoints, this value is used to reserve the bus time in the schedule, required for the per-(micro)frame data payloads. The pipe may, on an ongoing basis, actually use less bandwidth than that reserved. The device reports, if necessary, the actual bandwidth used via its normal, non-USB defined mechanisms. \n For all endpoints, bits 10..0 specify the maximum packet size (in bytes). \n For high-speed isochronous and interrupt endpoints: \n Bits 12..11 specify the number of additional transaction opportunities per microframe: \n- 00 = None (1 transaction per microframe) \n- 01 = 1 additional (2 per microframe) \n- 10 = 2 additional (3 per microframe) \n- 11 = Reserved \n Bits 15..13 are reserved and must be set to zero.
   uint8_t  bInterval        ; ///< Interval for polling endpoint for data transfers. Expressed in frames or microframes depending on the device operating speed (i.e., either 1 millisecond or 125 us units). \n- For full-/high-speed isochronous endpoints, this value must be in the range from 1 to 16. The bInterval value is used as the exponent for a \f$ 2^(bInterval-1) \f$ value; e.g., a bInterval of 4 means a period of 8 (\f$ 2^(4-1) \f$). \n- For full-/low-speed interrupt endpoints, the value of this field may be from 1 to 255. \n- For high-speed interrupt endpoints, the bInterval value is used as the exponent for a \f$ 2^(bInterval-1) \f$ value; e.g., a bInterval of 4 means a period of 8 (\f$ 2^(4-1) \f$) . This value must be from 1 to 16. \n- For high-speed bulk/control OUT endpoints, the bInterval must specify the maximum NAK rate of the endpoint. A value of 0 indicates the endpoint never NAKs. Other values indicate at most 1 NAK each bInterval number of microframes. This value must be in the range from 0 to 255. \n Refer to Chapter 5 of USB 2.0 specification for more information.
 } tusb_descriptor_endpoint_t;

tinyusb/core/std_request.h

@@ -61,7 +61,7 @@
 #include "common/binary.h"
 
 typedef ATTR_PREPACKED struct ATTR_PACKED {
-  struct {
+  ATTR_PREPACKED struct ATTR_PACKED {
     uint8_t recipient :  5; /**< Recipient type. */
     uint8_t type      :  2; /**< Request type.  */
     uint8_t direction :  1; /**< Direction type. */

tinyusb/core/tusb_types.h

@@ -161,6 +161,7 @@ enum {
   TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP = BIT_(5)
 };
 
+#define TUSB_DESC_CONFIG_POWER_MA(x)  ((x)/2)
 #ifdef __cplusplus
  }
 #endif