adding tud_isr/tuh_isr with lpc18/43

hw/bsp/ea4357/board.mk

@@ -16,9 +16,6 @@ MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx
 # All source paths should be relative to the top level.
 LD_FILE = hw/bsp/ea4357/lpc4357.ld
 
-# TODO remove later
-SRC_C += src/portable/$(VENDOR)/$(CHIP_FAMILY)/hal_$(CHIP_FAMILY).c
-
 SRC_C += \
 	$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \
 	$(MCU_DIR)/src/chip_18xx_43xx.c \

hw/bsp/ea4357/ea4357.c

@@ -230,6 +230,31 @@ void board_init(void)
   // TODO Remove R170, R171, solder a pair of 15K to USB1 D+/D- to test with USB1 Host
 }
 
+//--------------------------------------------------------------------+
+// USB Interrupt Handler
+//--------------------------------------------------------------------+
+void USB0_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(0);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(0);
+  #endif
+}
+
+void USB1_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(1);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(1);
+  #endif
+}
+
 //--------------------------------------------------------------------+
 // Board porting API
 //--------------------------------------------------------------------+

hw/bsp/mcb1800/board.mk

@@ -16,9 +16,6 @@ MCU_DIR = hw/mcu/nxp/lpcopen/lpc18xx/lpc_chip_18xx
 # All source paths should be relative to the top level.
 LD_FILE = hw/bsp/mcb1800/lpc1857.ld
 
-# TODO remove later
-SRC_C += src/portable/$(VENDOR)/$(CHIP_FAMILY)/hal_$(CHIP_FAMILY).c
-
 SRC_C += \
 	$(MCU_DIR)/../gcc/cr_startup_lpc18xx.c \
 	$(MCU_DIR)/src/chip_18xx_43xx.c \

hw/bsp/mcb1800/mcb1800.c

@@ -172,6 +172,31 @@ void board_init(void)
 #endif
 }
 
+//--------------------------------------------------------------------+
+// USB Interrupt Handler
+//--------------------------------------------------------------------+
+void USB0_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(0);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(0);
+  #endif
+}
+
+void USB1_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(1);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(1);
+  #endif
+}
+
 //--------------------------------------------------------------------+
 // Board porting API
 //--------------------------------------------------------------------+

hw/bsp/ngx4330/board.mk

@@ -16,9 +16,6 @@ MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx
 # All source paths should be relative to the top level.
 LD_FILE = hw/bsp/$(BOARD)/ngx4330.ld
 
-# TODO remove later
-SRC_C += src/portable/$(VENDOR)/$(CHIP_FAMILY)/hal_$(CHIP_FAMILY).c
-
 SRC_C += \
 	$(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \
 	$(MCU_DIR)/src/chip_18xx_43xx.c \

hw/bsp/ngx4330/ngx4330.c

@@ -219,6 +219,31 @@ void board_init(void)
 #endif
 }
 
+//--------------------------------------------------------------------+
+// USB Interrupt Handler
+//--------------------------------------------------------------------+
+void USB0_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(0);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(0);
+  #endif
+}
+
+void USB1_IRQHandler(void)
+{
+  #if TUSB_OPT_HOST_ENABLED
+    tuh_isr(1);
+  #endif
+
+  #if TUSB_OPT_DEVICE_ENABLED
+    tud_isr(1);
+  #endif
+}
+
 //--------------------------------------------------------------------+
 // Board porting API
 //--------------------------------------------------------------------+