add stm32f103 mini v2.0 board

2021-08-19 18:51:51 +07:00
parent 1992f49343
commit ebfd65a9ca
7 changed files with 277 additions and 6 deletions
--- a/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
+++ b/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
@@ -0,0 +1,92 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT              GPIOA
+#define LED_PIN               GPIO_PIN_8
+#define LED_STATE_ON          0
+
+// Button
+#define BUTTON_PORT           GPIOA
+#define BUTTON_PIN            GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE   1
+
+// UART
+//#define UART_DEV              USART1
+//#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
+//#define UART_GPIO_PORT        GPIOA
+//#define UART_GPIO_AF          GPIO_AF1_USART1
+//#define UART_TX_PIN           GPIO_PIN_9
+//#define UART_RX_PIN           GPIO_PIN_10
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32f1_clock_init(void)
+{
+  RCC_ClkInitTypeDef clkinitstruct = {0};
+  RCC_OscInitTypeDef oscinitstruct = {0};
+  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source */
+  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
+  oscinitstruct.HSEState        = RCC_HSE_ON;
+  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
+  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
+  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
+  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
+  HAL_RCC_OscConfig(&oscinitstruct);
+
+  /* USB clock selection */
+  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
+  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */