124 lines
4.5 KiB
C
124 lines
4.5 KiB
C
/**************************************************************************/
|
|
/*!
|
|
@file hal_lpc43xx.c
|
|
@author hathach (tinyusb.org)
|
|
|
|
@section LICENSE
|
|
|
|
Software License Agreement (BSD License)
|
|
|
|
Copyright (c) 2013, hathach (tinyusb.org)
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
1. Redistributions of source code must retain the above copyright
|
|
notice, this list of conditions and the following disclaimer.
|
|
2. Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in the
|
|
documentation and/or other materials provided with the distribution.
|
|
3. Neither the name of the copyright holders nor the
|
|
names of its contributors may be used to endorse or promote products
|
|
derived from this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
|
|
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
|
|
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
|
|
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
This file is part of the tinyusb stack.
|
|
*/
|
|
/**************************************************************************/
|
|
|
|
#include "common/common.h"
|
|
#include "hal.h"
|
|
|
|
#if MCU == MCU_LPC43XX
|
|
|
|
#include "lpc43xx_cgu.h"
|
|
#include "lpc43xx_scu.h"
|
|
|
|
enum {
|
|
LPC43XX_USBMODE_DEVICE = 2,
|
|
LPC43XX_USBMODE_HOST = 3
|
|
};
|
|
|
|
enum {
|
|
LPC43XX_USBMODE_VBUS_LOW = 0,
|
|
LPC43XX_USBMODE_VBUS_HIGH = 1
|
|
};
|
|
|
|
tusb_error_t hal_init(void)
|
|
{
|
|
//------------- USB0 Clock -------------//
|
|
#if TUSB_CFG_CONTROLLER_0_MODE
|
|
CGU_EnableEntity(CGU_CLKSRC_PLL0, DISABLE); /* Disable PLL first */
|
|
ASSERT_INT( CGU_ERROR_SUCCESS, CGU_SetPLL0(), TUSB_ERROR_FAILED); /* the usb core require output clock = 480MHz */
|
|
CGU_EntityConnect(CGU_CLKSRC_XTAL_OSC, CGU_CLKSRC_PLL0);
|
|
CGU_EnableEntity(CGU_CLKSRC_PLL0, ENABLE); /* Enable PLL after all setting is done */
|
|
LPC_CREG->CREG0 &= ~(1<<5); /* Turn on the phy */
|
|
|
|
// reset controller & set role
|
|
#if TUSB_CFG_CONTROLLER_0_MODE & TUSB_MODE_HOST
|
|
hcd_controller_reset(0); // TODO where to place prototype
|
|
LPC_USB0->USBMODE_H = LPC43XX_USBMODE_HOST | (LPC43XX_USBMODE_VBUS_HIGH << 5);
|
|
#else // TODO OTG
|
|
// dcd_controller_reset(0);
|
|
// LPC_USB0->USBMODE_D = LPC43XX_USBMODE_DEVICE;
|
|
// LPC_USB0->OTGSC = (1<<3) | (1<<0) /*| (1<<16)| (1<<24)| (1<<25)| (1<<26)| (1<<27)| (1<<28)| (1<<29)| (1<<30)*/;
|
|
// LPC_USB0->PORTSC1_D |= (1<<24); // force full speed
|
|
// dcd_controller_connect(0);
|
|
#endif
|
|
|
|
hal_interrupt_enable(0);
|
|
#endif
|
|
|
|
//------------- USB1 Clock, only use on-chip FS PHY -------------//
|
|
#if TUSB_CFG_CONTROLLER_1_MODE
|
|
// TODO confirm whether device mode require P2_5 or not
|
|
scu_pinmux(0x2, 5, MD_PLN | MD_EZI | MD_ZI, FUNC2); // USB1_VBUS monitor presence, must be high for bus reset occur
|
|
|
|
/* connect CLK_USB1 to 60 MHz clock */
|
|
CGU_EntityConnect(CGU_CLKSRC_PLL1, CGU_BASE_USB1); /* FIXME Run base BASE_USB1_CLK clock from PLL1 (assume PLL1 is 60 MHz, no division required) */
|
|
//LPC_CREG->CREG0 &= ~(1<<5); /* Turn on the phy */
|
|
LPC_SCU->SFSUSB = (TUSB_CFG_CONTROLLER_1_MODE & TUSB_MODE_HOST) ? 0x16 : 0x12; // enable USB1 with on-chip FS PHY
|
|
|
|
#if TUSB_CFG_CONTROLLER_1_MODE & TUSB_MODE_HOST
|
|
hcd_controller_reset(1); // TODO where to place prototype
|
|
LPC_USB1->USBMODE_H = LPC43XX_USBMODE_HOST | (LPC43XX_USBMODE_VBUS_HIGH << 5);
|
|
#else // TODO OTG
|
|
// dcd_controller_reset(1);
|
|
LPC_USB0->USBMODE_D = LPC43XX_USBMODE_DEVICE;
|
|
dcd_controller_connect(1);
|
|
#endif
|
|
|
|
LPC_USB1->PORTSC1_D |= (1<<24); // TODO abtract, force port to fullspeed
|
|
|
|
hal_interrupt_enable(1);
|
|
#endif
|
|
|
|
return TUSB_ERROR_NONE;
|
|
}
|
|
|
|
#if TUSB_CFG_CONTROLLER_0_MODE
|
|
void USB0_IRQHandler(void)
|
|
{
|
|
tusb_isr(0);
|
|
}
|
|
#endif
|
|
|
|
#if TUSB_CFG_CONTROLLER_1_MODE
|
|
void USB1_IRQHandler(void)
|
|
{
|
|
tusb_isr(1);
|
|
}
|
|
#endif
|
|
|
|
#endif
|