63 lines
1.5 KiB
Makefile
63 lines
1.5 KiB
Makefile
# Default is Highspeed port
|
|
PORT ?= 1
|
|
|
|
CFLAGS += \
|
|
-flto \
|
|
-mthumb \
|
|
-mabi=aapcs \
|
|
-mcpu=cortex-m7 \
|
|
-mfloat-abi=hard \
|
|
-mfpu=fpv5-d16 \
|
|
-nostdlib -nostartfiles \
|
|
-DSTM32H743xx \
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32H7 \
|
|
-DBOARD_DEVICE_RHPORT_NUM=$(PORT)
|
|
|
|
ifeq ($(PORT), 1)
|
|
CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
|
|
$(info "PORT1 High Speed")
|
|
else
|
|
$(info "PORT0 Full Speed")
|
|
endif
|
|
|
|
# suppress warning caused by vendor mcu driver
|
|
CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align
|
|
|
|
ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver
|
|
ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx
|
|
|
|
# All source paths should be relative to the top level.
|
|
LD_FILE = hw/bsp/$(BOARD)/STM32H743XIHx_FLASH.ld
|
|
|
|
SRC_C += \
|
|
$(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_cortex.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c
|
|
|
|
SRC_S += \
|
|
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
|
|
|
|
INC += \
|
|
$(TOP)/hw/mcu/st/st_driver/CMSIS/Include \
|
|
$(TOP)/$(ST_CMSIS)/Include \
|
|
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
|
$(TOP)/hw/bsp/$(BOARD)
|
|
|
|
# For TinyUSB port source
|
|
VENDOR = st
|
|
CHIP_FAMILY = synopsys
|
|
|
|
# For freeRTOS port source
|
|
FREERTOS_PORT = ARM_CM7/r0p1
|
|
|
|
# For flash-jlink target
|
|
JLINK_DEVICE = stm32h743xi
|
|
|
|
# flash target using on-board stlink
|
|
flash: flash-stlink
|