andy/tinyUSB
1
0
Fork 0
Code Issues Pull Requests Actions 1 Packages Projects Releases Wiki Activity
Files
55db123a85d464462562f4c64efa8d6ff5734dce
tinyUSB/hw/mcu/dialog/da1469x/src/hal_gpio.c
Jerzy Kasenberg 8e143fc962 Add board support for Dialog DA1469x-dk-pro 
This adds source files that allow to run TinyUSB stack on DA1469x-dk-pro board.
Source files .c .S and .ld are taken from Apache Mynewt repository.
Those files were stripped to allow starting board without Mynewt os.
2020-06-29 11:02:32 +02:00

479 lines
13 KiB
C
Raw Blame History

/*
* Licensed to the Apache Software Foundation (ASF) under one
* or more contributor license agreements. See the NOTICE file
* distributed with this work for additional information
* regarding copyright ownership. The ASF licenses this file
* to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance
* with the License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing,
* software distributed under the License is distributed on an
* "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
* KIND, either express or implied. See the License for the
* specific language governing permissions and limitations
* under the License.
*/
#include <assert.h>
#include <stddef.h>
#include "syscfg/syscfg.h"
#include "mcu/da1469x_hal.h"
#include <mcu/mcu.h>
#include "hal/hal_gpio.h"
/* GPIO interrupts */
#define HAL_GPIO_MAX_IRQ MYNEWT_VAL(MCU_GPIO_MAX_IRQ)
#define GPIO_REG(name) ((__IO uint32_t *)(GPIO_BASE + offsetof(GPIO_Type, name)))
#define WAKEUP_REG(name) ((__IO uint32_t *)(WAKEUP_BASE + offsetof(WAKEUP_Type, name)))
#define CRG_TOP_REG(name) ((__IO uint32_t *)(CRG_TOP_BASE + offsetof(CRG_TOP_Type, name)))
#ifndef MCU_GPIO_PORT0_PIN_COUNT
#define MCU_GPIO_PORT0_PIN_COUNT 32
#endif
#if (MCU_GPIO_PORT0_PIN_COUNT) == 32
#define GPIO_PORT(pin) (((unsigned)(pin)) >> 5U)
#define GPIO_PORT_PIN(pin) (((unsigned)(pin)) & 31U)
#else
#define GPIO_PORT(pin) (((unsigned)(pin)) < MCU_GPIO_PORT0_PIN_COUNT ? 0 : 1)
#define GPIO_PORT_PIN(pin) ((unsigned)(pin) < MCU_GPIO_PORT0_PIN_COUNT ? \
(pin) : (pin) - MCU_GPIO_PORT0_PIN_COUNT)
#endif
#define GPIO_PIN_BIT(pin) (1 << GPIO_PORT_PIN(pin))
#define GPIO_PIN_DATA_REG_ADDR(pin) (GPIO_REG(P0_DATA_REG) + GPIO_PORT(pin))
#define GPIO_PIN_DATA_REG(pin) *GPIO_PIN_DATA_REG_ADDR(pin)
#define GPIO_PIN_SET_DATA_REG_ADDR(pin) (GPIO_REG(P0_SET_DATA_REG) + GPIO_PORT(pin))
#define GPIO_PIN_SET_DATA_REG(pin) *GPIO_PIN_SET_DATA_REG_ADDR(pin)
#define GPIO_PIN_RESET_DATA_REG_ADDR(pin) (GPIO_REG(P0_RESET_DATA_REG) + GPIO_PORT(pin))
#define GPIO_PIN_RESET_DATA_REG(pin) *GPIO_PIN_RESET_DATA_REG_ADDR(pin)
#define GPIO_PIN_MODE_REG_ADDR(pin) (GPIO_REG(P0_00_MODE_REG) + (pin))
#define GPIO_PIN_MODE_REG(pin) *GPIO_PIN_MODE_REG_ADDR(pin)
#define GPIO_PIN_PADPWR_CTRL_REG_ADDR(pin) (GPIO_REG(P0_PADPWR_CTRL_REG) + GPIO_PORT(pin))
#define GPIO_PIN_PADPWR_CTRL_REG(pin) *GPIO_PIN_PADPWR_CTRL_REG_ADDR(pin)
#define GPIO_PIN_UNLATCH_ADDR(pin) (CRG_TOP_REG(P0_SET_PAD_LATCH_REG) + GPIO_PORT(pin) * 3)
#define GPIO_PIN_LATCH_ADDR(pin) (CRG_TOP_REG(P0_RESET_PAD_LATCH_REG) + GPIO_PORT(pin) * 3)
#define WKUP_CTRL_REG_ADDR (WAKEUP_REG(WKUP_CTRL_REG))
#define WKUP_RESET_IRQ_REG_ADDR (WAKEUP_REG(WKUP_RESET_IRQ_REG))
#define WKUP_SELECT_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_SELECT_P0_REG) + GPIO_PORT(pin))
#define WKUP_SELECT_PX_REG(pin) *(WKUP_SELECT_PX_REG_ADDR(pin))
#define WKUP_POL_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_POL_P0_REG) + GPIO_PORT(pin))
#define WKUP_POL_PX_SET_FALLING(pin) do { *(WKUP_POL_PX_REG_ADDR(pin)) |= GPIO_PIN_BIT(pin); } while (0)
#define WKUP_POL_PX_SET_RISING(pin) do { *(WKUP_POL_PX_REG_ADDR(pin)) &= ~GPIO_PIN_BIT(pin); } while (0)
#define WKUP_STAT_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_STATUS_P0_REG) + GPIO_PORT(pin))
#define WKUP_STAT(pin) ((*(WKUP_STAT_PX_REG_ADDR(pin)) >> GPIO_PORT_PIN(pin)) & 1)
#define WKUP_CLEAR_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_CLEAR_P0_REG) + GPIO_PORT(pin))
#define WKUP_CLEAR_PX(pin) do { (*(WKUP_CLEAR_PX_REG_ADDR(pin)) = GPIO_PIN_BIT(pin)); } while (0)
#define WKUP_SEL_GPIO_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_SEL_GPIO_P0_REG) + GPIO_PORT(pin))
#define WKUP_SEL_GPIO_PX_REG(pin) *(WKUP_SEL_GPIO_PX_REG_ADDR(pin))
/* Storage for GPIO callbacks. */
struct hal_gpio_irq {
int pin;
hal_gpio_irq_handler_t func;
void *arg;
};
static struct hal_gpio_irq hal_gpio_irqs[HAL_GPIO_MAX_IRQ];
#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0
static uint32_t g_mcu_gpio_latch_state[2];
static uint8_t g_mcu_gpio_retained_num;
static struct da1469x_retreg g_mcu_gpio_retained[MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM)];
#endif
/*
* We assume that any latched pin has default configuration, i.e. was either
* not configured or was deinited. Any unlatched pin is considered to be used
* by someone.
*
* By default, all pins are assumed to have default configuration and are
* latched. This allows PD_COM to be disabled (if no other peripheral needs
* it) since we do not need GPIO mux to be active.
*
* Configuration of any pin shall be done as follows, with interrupts disabled:
* 1. call mcu_gpio_unlatch_prepare() to enable PD_COM if needed
* 2. configure pin
* 3. call mcu_gpio_unlatch() to actually unlatch pin
*
* Once pin is restored to default configuration it shall be latched again by
* calling mcu_gpio_latch().
*/
#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0
static void
mcu_gpio_retained_add_port(uint32_t latch_val, volatile uint32_t *base_reg)
{
struct da1469x_retreg *retreg;
int pin;
retreg = &g_mcu_gpio_retained[g_mcu_gpio_retained_num];
while (latch_val) {
assert(g_mcu_gpio_retained_num < MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM));
pin = __builtin_ctz(latch_val);
latch_val &= ~(1 << pin);
da1469x_retreg_assign(retreg, &base_reg[pin]);
g_mcu_gpio_retained_num++;
retreg++;
}
}
#endif
static void
mcu_gpio_retained_refresh(void)
{
#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0
g_mcu_gpio_retained_num = 0;
mcu_gpio_retained_add_port(CRG_TOP->P0_PAD_LATCH_REG, &GPIO->P0_00_MODE_REG);
mcu_gpio_retained_add_port(CRG_TOP->P1_PAD_LATCH_REG, &GPIO->P1_00_MODE_REG);
#endif
}
static inline void
mcu_gpio_unlatch_prepare(int pin)
{
__HAL_ASSERT_CRITICAL();
(void)pin;
/* Acquire PD_COM if first pin will be unlatched */
// if ((CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG) == 0) {
// da1469x_pd_acquire(MCU_PD_DOMAIN_COM);
// }
}
static inline void
mcu_gpio_unlatch(int pin)
{
__HAL_ASSERT_CRITICAL();
*GPIO_PIN_UNLATCH_ADDR(pin) = GPIO_PIN_BIT(pin);
mcu_gpio_retained_refresh();
}
static inline void
mcu_gpio_latch(int pin)
{
(void)pin;
// uint32_t primask;
// uint32_t latch_pre;
// uint32_t latch_post;
//
// __HAL_DISABLE_INTERRUPTS(primask);
//
// latch_pre = CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG;
//
// *GPIO_PIN_LATCH_ADDR(pin) = GPIO_PIN_BIT(pin);
// mcu_gpio_retained_refresh();
//
// latch_post = CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG;
//
// /* Release PD_COM if last pin was latched */
// if (latch_pre && !latch_post) {
// da1469x_pd_release(MCU_PD_DOMAIN_COM);
// }
//
// __HAL_ENABLE_INTERRUPTS(primask);
}
int
hal_gpio_init_in(int pin, hal_gpio_pull_t pull)
{
volatile uint32_t *px_xx_mod_reg = GPIO_PIN_MODE_REG_ADDR(pin);
uint32_t regval;
uint32_t primask;
switch (pull) {
case HAL_GPIO_PULL_UP:
regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT_PULLUP;
break;
case HAL_GPIO_PULL_DOWN:
regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT_PULLDOWN;
break;
case HAL_GPIO_PULL_NONE:
regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT;
break;
default:
return -1;
}
__HAL_DISABLE_INTERRUPTS(primask);
mcu_gpio_unlatch_prepare(pin);
*px_xx_mod_reg = regval;
mcu_gpio_unlatch(pin);
__HAL_ENABLE_INTERRUPTS(primask);
return 0;
}
int
hal_gpio_init_out(int pin, int val)
{
uint32_t primask;
__HAL_DISABLE_INTERRUPTS(primask);
mcu_gpio_unlatch_prepare(pin);
GPIO_PIN_MODE_REG(pin) = MCU_GPIO_MODE_OUTPUT;
if (val) {
GPIO_PIN_SET_DATA_REG(pin) = GPIO_PIN_BIT(pin);
} else {
GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin);
}
mcu_gpio_unlatch(pin);
__HAL_ENABLE_INTERRUPTS(primask);
return 0;
}
int
hal_gpio_deinit(int pin)
{
/* Reset mode to default value and latch pin */
GPIO_PIN_MODE_REG(pin) = 0x200;
GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin);
mcu_gpio_latch(pin);
return 0;
}
void
hal_gpio_write(int pin, int val)
{
if (val) {
GPIO_PIN_SET_DATA_REG(pin) = GPIO_PIN_BIT(pin);
} else {
GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin);
}
}
int
hal_gpio_read(int pin)
{
return (GPIO_PIN_DATA_REG(pin) >> GPIO_PORT_PIN(pin)) & 1;
}
int
hal_gpio_toggle(int pin)
{
int new_value = hal_gpio_read(pin) == 0;
hal_gpio_write(pin, new_value);
return new_value;
}
static void
hal_gpio_irq_handler(void)
{
struct hal_gpio_irq *irq;
uint32_t stat;
int i;
*WKUP_RESET_IRQ_REG_ADDR = 1;
NVIC_ClearPendingIRQ(KEY_WKUP_GPIO_IRQn);
for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) {
irq = &hal_gpio_irqs[i];
/* Read latched status value from relevant GPIO port */
stat = WKUP_STAT(irq->pin);
if (irq->func && stat) {
irq->func(irq->arg);
}
WKUP_CLEAR_PX(irq->pin);
}
}
static void
hal_gpio_irq_setup(void)
{
static uint8_t irq_setup;
int sr;
if (!irq_setup) {
__HAL_DISABLE_INTERRUPTS(sr);
irq_setup = 1;
NVIC_ClearPendingIRQ(GPIO_P0_IRQn);
NVIC_ClearPendingIRQ(GPIO_P1_IRQn);
NVIC_SetVector(GPIO_P0_IRQn, (uint32_t)hal_gpio_irq_handler);
NVIC_SetVector(GPIO_P1_IRQn, (uint32_t)hal_gpio_irq_handler);
WAKEUP->WKUP_CTRL_REG = 0;
WAKEUP->WKUP_CLEAR_P0_REG = 0xFFFFFFFF;
WAKEUP->WKUP_CLEAR_P1_REG = 0x007FFFFF;
WAKEUP->WKUP_SELECT_P0_REG = 0;
WAKEUP->WKUP_SELECT_P1_REG = 0;
WAKEUP->WKUP_SEL_GPIO_P0_REG = 0;
WAKEUP->WKUP_SEL_GPIO_P1_REG = 0;
WAKEUP->WKUP_RESET_IRQ_REG = 0;
CRG_TOP->CLK_TMR_REG |= CRG_TOP_CLK_TMR_REG_WAKEUPCT_ENABLE_Msk;
__HAL_ENABLE_INTERRUPTS(sr);
NVIC_EnableIRQ(GPIO_P0_IRQn);
NVIC_EnableIRQ(GPIO_P1_IRQn);
}
}
static int
hal_gpio_find_empty_slot(void)
{
int i;
for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) {
if (hal_gpio_irqs[i].func == NULL) {
return i;
}
}
return -1;
}
int
hal_gpio_irq_init(int pin, hal_gpio_irq_handler_t handler, void *arg,
hal_gpio_irq_trig_t trig, hal_gpio_pull_t pull)
{
int i;
hal_gpio_irq_setup();
i = hal_gpio_find_empty_slot();
/* If assert failed increase syscfg value MCU_GPIO_MAX_IRQ */
assert(i >= 0);
if (i < 0) {
return -1;
}
hal_gpio_init_in(pin, pull);
switch (trig) {
case HAL_GPIO_TRIG_RISING:
WKUP_POL_PX_SET_RISING(pin);
break;
case HAL_GPIO_TRIG_FALLING:
WKUP_POL_PX_SET_FALLING(pin);
break;
case HAL_GPIO_TRIG_BOTH:
/* Not supported */
default:
return -1;
}
hal_gpio_irqs[i].pin = pin;
hal_gpio_irqs[i].func = handler;
hal_gpio_irqs[i].arg = arg;
return 0;
}
void
hal_gpio_irq_release(int pin)
{
int i;
hal_gpio_irq_disable(pin);
for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) {
if (hal_gpio_irqs[i].pin == pin && hal_gpio_irqs[i].func) {
hal_gpio_irqs[i].pin = -1;
hal_gpio_irqs[i].arg = NULL;
hal_gpio_irqs[i].func = NULL;
}
}
}
void
hal_gpio_irq_enable(int pin)
{
WKUP_SEL_GPIO_PX_REG(pin) |= GPIO_PIN_BIT(pin);
}
void
hal_gpio_irq_disable(int pin)
{
WKUP_SEL_GPIO_PX_REG(pin) &= ~GPIO_PIN_BIT(pin);
WKUP_CLEAR_PX(pin);
}
void
mcu_gpio_set_pin_function(int pin, int mode, mcu_gpio_func func)
{
uint32_t primask;
__HAL_DISABLE_INTERRUPTS(primask);
mcu_gpio_unlatch_prepare(pin);
GPIO_PIN_MODE_REG(pin) = (func & GPIO_P0_00_MODE_REG_PID_Msk) |
(mode & (GPIO_P0_00_MODE_REG_PUPD_Msk | GPIO_P0_00_MODE_REG_PPOD_Msk));
mcu_gpio_unlatch(pin);
__HAL_ENABLE_INTERRUPTS(primask);
}
void
mcu_gpio_enter_sleep(void)
{
#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0
if (g_mcu_gpio_retained_num == 0) {
return;
}
g_mcu_gpio_latch_state[0] = CRG_TOP->P0_PAD_LATCH_REG;
g_mcu_gpio_latch_state[1] = CRG_TOP->P1_PAD_LATCH_REG;
da1469x_retreg_update(g_mcu_gpio_retained, g_mcu_gpio_retained_num);
CRG_TOP->P0_RESET_PAD_LATCH_REG = CRG_TOP_P0_PAD_LATCH_REG_P0_LATCH_EN_Msk;
CRG_TOP->P1_RESET_PAD_LATCH_REG = CRG_TOP_P1_PAD_LATCH_REG_P1_LATCH_EN_Msk;
da1469x_pd_release(MCU_PD_DOMAIN_COM);
#endif
}
void
mcu_gpio_exit_sleep(void)
{
#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0
if (g_mcu_gpio_retained_num == 0) {
return;
}
da1469x_pd_acquire(MCU_PD_DOMAIN_COM);
da1469x_retreg_restore(g_mcu_gpio_retained, g_mcu_gpio_retained_num);
/* Set pins states to their latched values */
GPIO->P0_DATA_REG = GPIO->P0_DATA_REG;
GPIO->P1_DATA_REG = GPIO->P1_DATA_REG;
CRG_TOP->P0_PAD_LATCH_REG = g_mcu_gpio_latch_state[0];
CRG_TOP->P1_PAD_LATCH_REG = g_mcu_gpio_latch_state[1];
#endif
}
Reference in New Issue View Git Blame Copy Permalink