144 lines
5.1 KiB
C
144 lines
5.1 KiB
C
/**************************************************************************/
|
|
/*!
|
|
@file board_ea4357.h
|
|
@author hathach (tinyusb.org)
|
|
|
|
@section LICENSE
|
|
|
|
Software License Agreement (BSD License)
|
|
|
|
Copyright (c) 2013, hathach (tinyusb.org)
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
1. Redistributions of source code must retain the above copyright
|
|
notice, this list of conditions and the following disclaimer.
|
|
2. Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in the
|
|
documentation and/or other materials provided with the distribution.
|
|
3. Neither the name of the copyright holders nor the
|
|
names of its contributors may be used to endorse or promote products
|
|
derived from this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
|
|
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
|
|
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
|
|
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
This file is part of the tinyusb stack.
|
|
*/
|
|
/**************************************************************************/
|
|
|
|
/** \file
|
|
* \brief TBD
|
|
*
|
|
* \note TBD
|
|
*/
|
|
|
|
/** \ingroup TBD
|
|
* \defgroup TBD
|
|
* \brief TBD
|
|
*
|
|
* @{
|
|
*/
|
|
|
|
#ifndef _TUSB_BOARD_EA4357_H_
|
|
#define _TUSB_BOARD_EA4357_H_
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include "LPC43xx.h"
|
|
#include "lpc43xx_scu.h"
|
|
#include "lpc43xx_cgu.h"
|
|
#include "lpc43xx_gpio.h"
|
|
#include "lpc43xx_uart.h"
|
|
#include "lpc43xx_i2c.h"
|
|
|
|
|
|
#include "oem_base_board/pca9532.h" // LEDs
|
|
|
|
|
|
//#define CFG_PRINTF_TARGET PRINTF_TARGET_SWO
|
|
#define CFG_PRINTF_TARGET PRINTF_TARGET_UART // FIXME keil's cmsis rtx does not work with UART (work with SWO)
|
|
|
|
/*=========================================================================
|
|
HARDWARE MAC ADDRESS
|
|
-----------------------------------------------------------------------*/
|
|
#define BOARD_MAC_ADDR0 0x00
|
|
#define BOARD_MAC_ADDR1 0x10
|
|
#define BOARD_MAC_ADDR2 0x20
|
|
#define BOARD_MAC_ADDR3 0x30
|
|
#define BOARD_MAC_ADDR4 0x40
|
|
#define BOARD_MAC_ADDR5 0x50
|
|
/*=========================================================================*/
|
|
|
|
/*=========================================================================
|
|
EMAC CONFIGURATION
|
|
-----------------------------------------------------------------------*/
|
|
/* The PHY address connected the to MII/RMII */
|
|
#define LPC_PHYDEF_PHYADDR 1 /**< The PHY address on the PHY device. */
|
|
|
|
/* Enable autonegotiation mode.
|
|
* If this is enabled, the PHY will attempt to auto-negotiate the
|
|
* best link mode if the PHY supports it. If this is not enabled,
|
|
* the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
|
|
* used to select the link mode. Note that auto-negotiation may
|
|
* take a few seconds to complete.
|
|
*/
|
|
#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
|
|
|
|
/* Sets up the PHY interface to either full duplex operation or
|
|
* half duplex operation if PHY_USE_AUTONEG is not enabled.
|
|
*/
|
|
#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
|
|
|
|
/* Sets up the PHY interface to either 100MBS operation or 10MBS
|
|
* operation if PHY_USE_AUTONEG is not enabled.
|
|
*/
|
|
#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
|
|
|
|
/* Selects RMII or MII connection type in the EMAC peripheral */
|
|
#define LPC_EMAC_RMII 1 /**< Use the RMII or MII driver variant */
|
|
|
|
/* Defines the number of descriptors used for RX */
|
|
#define LPC_NUM_BUFF_RXDESCS 20
|
|
|
|
/* Defines the number of descriptors used for TX */
|
|
#define LPC_NUM_BUFF_TXDESCS 20
|
|
|
|
/* Enables slow speed memory buffering
|
|
* Enable this define if you expect to transfer packets directly
|
|
* from SPI FLASH or any slower memory. This will add a check
|
|
* before queueing up the transfer pbuf to make sure the packet
|
|
* is not in slow memoey (defined by the LPC_SLOWMEM_ARRAY). If
|
|
* the packet does exists in slow memory, a pbuf will be created
|
|
* in the PBUF_RAM pool, copied to it, and sent from there.
|
|
*/
|
|
#define LPC_CHECK_SLOWMEM 0
|
|
|
|
/* Array of slow memory addresses for LPC_CHECK_SLOWMEM
|
|
* Define the array - start and ending address - for the slow
|
|
* memory regions in the system that need pbuf copies.
|
|
*
|
|
* Not defined since LPC_CHECK_SLOWMEM = 0.
|
|
*/
|
|
#define LPC_SLOWMEM_ARRAY
|
|
/*=========================================================================*/
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* _TUSB_BOARD_EA4357_H_ */
|
|
|
|
/** @} */
|