54 lines
1.7 KiB
Makefile
54 lines
1.7 KiB
Makefile
CFLAGS += \
|
|
-flto \
|
|
-mthumb \
|
|
-mabi=aapcs-linux \
|
|
-mcpu=cortex-m4 \
|
|
-mfloat-abi=hard \
|
|
-mfpu=fpv4-sp-d16 \
|
|
-nostdlib -nostartfiles \
|
|
-D__SAMD51J19A__ \
|
|
-DCFG_TUSB_MCU=OPT_MCU_SAMD51
|
|
|
|
CFLAGS += -Wno-error=undef
|
|
|
|
# All source paths should be relative to the top level.
|
|
LD_FILE = hw/bsp/$(BOARD)/samd51g19a_flash.ld
|
|
|
|
SRC_C += \
|
|
hw/mcu/microchip/samd/asf4/samd51/gcc/gcc/startup_samd51.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/gcc/system_samd51.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/hpl/gclk/hpl_gclk.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/hpl/mclk/hpl_mclk.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/hpl/osc32kctrl/hpl_osc32kctrl.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/hpl/oscctrl/hpl_oscctrl.c \
|
|
hw/mcu/microchip/samd/asf4/samd51/hal/src/hal_atomic.c
|
|
|
|
INC += \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/ \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/config \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/include \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/hal/include \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/hal/utils/include \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/hpl/port \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/hri \
|
|
$(TOP)/hw/mcu/microchip/samd/asf4/samd51/CMSIS/Include
|
|
|
|
# For TinyUSB port source
|
|
VENDOR = microchip
|
|
CHIP_FAMILY = samd
|
|
|
|
# For freeRTOS port source
|
|
FREERTOS_PORT = ARM_CM4F
|
|
|
|
# For flash-jlink target
|
|
JLINK_DEVICE = ATSAMD51J19
|
|
|
|
# flash using bossac at least version 1.8
|
|
# can be found in arduino15/packages/arduino/tools/bossac/
|
|
# Add it to your PATH or change BOSSAC variable to match your installation
|
|
BOSSAC = bossac
|
|
|
|
flash: $(BUILD)/$(BOARD)-firmware.bin
|
|
@:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0)
|
|
$(BOSSAC) --port=$(SERIAL) -U -i --offset=0x4000 -e -w $^ -R
|