111 lines
4.1 KiB
C
111 lines
4.1 KiB
C
/*
|
|
* The MIT License (MIT)
|
|
*
|
|
* Copyright (c) 2020, Ha Thach (tinyusb.org)
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*
|
|
* This file is part of the TinyUSB stack.
|
|
*/
|
|
|
|
#ifndef BOARD_H_
|
|
#define BOARD_H_
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
// LED
|
|
#define LED_PORT GPIOA
|
|
#define LED_PIN GPIO_PIN_5
|
|
#define LED_STATE_ON 1
|
|
|
|
// Button
|
|
#define BUTTON_PORT GPIOA
|
|
#define BUTTON_PIN GPIO_PIN_0
|
|
#define BUTTON_STATE_ACTIVE 1
|
|
|
|
// UART
|
|
//#define UART_DEV USART2
|
|
//#define UART_CLK_EN __HAL_RCC_USART2_CLK_ENABLE
|
|
//#define UART_GPIO_PORT GPIOA
|
|
//#define UART_GPIO_AF GPIO_AF4_USART2
|
|
//#define UART_TX_PIN GPIO_PIN_2
|
|
//#define UART_RX_PIN GPIO_PIN_3
|
|
|
|
//--------------------------------------------------------------------+
|
|
// RCC Clock
|
|
//--------------------------------------------------------------------+
|
|
static inline void board_stm32l0_clock_init(void)
|
|
{
|
|
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
|
|
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
|
|
RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
|
|
RCC_CRSInitTypeDef RCC_CRSInitStruct = {0};
|
|
|
|
/* Enable HSI Oscillator to be used as System clock source
|
|
Enable HSI48 Oscillator to be used as USB clock source */
|
|
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSI48;
|
|
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
|
|
RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
|
|
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
|
|
HAL_RCC_OscConfig(&RCC_OscInitStruct);
|
|
|
|
/* Select HSI48 as USB clock source */
|
|
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
|
|
PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
|
|
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
|
|
|
|
/* Select HSI as system clock source and configure the HCLK, PCLK1 and PCLK2
|
|
clock dividers */
|
|
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
|
|
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
|
|
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
|
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
|
|
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
|
|
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0);
|
|
|
|
/*Configure the clock recovery system (CRS)**********************************/
|
|
|
|
/*Enable CRS Clock*/
|
|
__HAL_RCC_CRS_CLK_ENABLE();
|
|
|
|
/* Default Synchro Signal division factor (not divided) */
|
|
RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1;
|
|
/* Set the SYNCSRC[1:0] bits according to CRS_Source value */
|
|
RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB;
|
|
/* HSI48 is synchronized with USB SOF at 1KHz rate */
|
|
RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000, 1000);
|
|
RCC_CRSInitStruct.ErrorLimitValue = RCC_CRS_ERRORLIMIT_DEFAULT;
|
|
/* Set the TRIM[5:0] to the default value*/
|
|
RCC_CRSInitStruct.HSI48CalibrationValue = 0x20;
|
|
/* Start automatic synchronization */
|
|
HAL_RCCEx_CRSConfig (&RCC_CRSInitStruct);
|
|
}
|
|
|
|
static inline void board_vbus_sense_init(void)
|
|
{
|
|
}
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* BOARD_H_ */
|