125 lines
4.1 KiB
C
125 lines
4.1 KiB
C
/**************************************************************************/
|
|
/*!
|
|
@file board_lpcxpresso1769.c
|
|
@author hathach (tinyusb.org)
|
|
|
|
@section LICENSE
|
|
|
|
Software License Agreement (BSD License)
|
|
|
|
Copyright (c) 2013, hathach (tinyusb.org)
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
1. Redistributions of source code must retain the above copyright
|
|
notice, this list of conditions and the following disclaimer.
|
|
2. Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in the
|
|
documentation and/or other materials provided with the distribution.
|
|
3. Neither the name of the copyright holders nor the
|
|
names of its contributors may be used to endorse or promote products
|
|
derived from this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
|
|
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
|
|
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
|
|
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
This file is part of the tinyusb stack.
|
|
*/
|
|
/**************************************************************************/
|
|
|
|
#include "../board.h"
|
|
|
|
#if BOARD == BOARD_LPCXPRESSO1769
|
|
|
|
#define BOARD_LED_PORT (0)
|
|
#define BOARD_LED_PIN (22)
|
|
|
|
#define BOARD_UART_PORT LPC_UART3
|
|
|
|
void board_init(void)
|
|
{
|
|
SystemInit();
|
|
SysTick_Config(SystemCoreClock / CFG_TICKS_PER_SECOND); // 1 msec tick timer
|
|
|
|
// Leds Init
|
|
GPIO_SetDir(BOARD_LED_PORT, BIT_(BOARD_LED_PIN), 1);
|
|
|
|
#if MODE_DEVICE_SUPPORTED
|
|
//------------- USB Device -------------//
|
|
// VBUS sense is wrongly connected to P0_5 (instead of P1_30). So we need to always pull P1_30 to high
|
|
// so that USB device block can work. However, Device Controller (thus tinyusb) cannot able to determine
|
|
// if device is disconnected or not
|
|
PINSEL_ConfigPin( &(PINSEL_CFG_Type) {
|
|
.Portnum = 1, .Pinnum = 30,
|
|
.Funcnum = 2, .Pinmode = PINSEL_PINMODE_PULLUP} );
|
|
|
|
//P0_21 instead of P2_9 as USB connect
|
|
#endif
|
|
|
|
#if CFG_UART_ENABLE
|
|
//------------- UART init -------------//
|
|
|
|
PINSEL_CFG_Type PinCfg =
|
|
{
|
|
.Portnum = 0,
|
|
.Pinnum = 0, // TXD is P0.0
|
|
.Funcnum = 2,
|
|
.OpenDrain = 0,
|
|
.Pinmode = 0
|
|
};
|
|
PINSEL_ConfigPin(&PinCfg);
|
|
|
|
PinCfg.Portnum = 0;
|
|
PinCfg.Pinnum = 1; // RXD is P0.1
|
|
PINSEL_ConfigPin(&PinCfg);
|
|
|
|
UART_CFG_Type UARTConfigStruct;
|
|
UART_ConfigStructInit(&UARTConfigStruct);
|
|
UARTConfigStruct.Baud_rate = CFG_UART_BAUDRATE;
|
|
|
|
UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
|
|
UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
|
|
#endif
|
|
}
|
|
|
|
//--------------------------------------------------------------------+
|
|
// LEDS
|
|
//--------------------------------------------------------------------+
|
|
void board_leds(uint32_t on_mask, uint32_t off_mask)
|
|
{
|
|
if (on_mask & BIT_(0))
|
|
{
|
|
GPIO_SetValue(BOARD_LED_PORT, BIT_(BOARD_LED_PIN));
|
|
}else if (off_mask & BIT_(0))
|
|
{
|
|
GPIO_ClearValue(BOARD_LED_PORT, BIT_(BOARD_LED_PIN));
|
|
}
|
|
}
|
|
|
|
//--------------------------------------------------------------------+
|
|
// UART
|
|
//--------------------------------------------------------------------+
|
|
#if CFG_UART_ENABLE
|
|
uint32_t board_uart_send(uint8_t *buffer, uint32_t length)
|
|
{
|
|
return UART_Send(BOARD_UART_PORT, buffer, length, BLOCKING);
|
|
}
|
|
|
|
uint8_t board_uart_getchar(void)
|
|
{
|
|
return UART_ReceiveByte(BOARD_UART_PORT);
|
|
}
|
|
|
|
#endif
|
|
|
|
#endif
|