246 lines
7.1 KiB
C
246 lines
7.1 KiB
C
/*
|
|
* The MIT License (MIT)
|
|
*
|
|
* Copyright (c) 2018, hathach (tinyusb.org)
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*
|
|
* This file is part of the TinyUSB stack.
|
|
*/
|
|
|
|
#include "bsp/board.h"
|
|
#include "fsl_device_registers.h"
|
|
#include "fsl_gpio.h"
|
|
#include "fsl_lpuart.h"
|
|
#include "board.h"
|
|
|
|
#include "pin_mux.h"
|
|
#include "clock_config.h"
|
|
|
|
#ifdef BOARD_TUD_RHPORT
|
|
#define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n)
|
|
#else
|
|
#define PORT_SUPPORT_DEVICE(_n) 0
|
|
#endif
|
|
|
|
#ifdef BOARD_TUH_RHPORT
|
|
#define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n)
|
|
#else
|
|
#define PORT_SUPPORT_HOST(_n) 0
|
|
#endif
|
|
|
|
//--------------------------------------------------------------------+
|
|
// MACRO TYPEDEF CONSTANT ENUM
|
|
//--------------------------------------------------------------------+
|
|
|
|
//--------------------------------------------------------------------+
|
|
// Forward USB interrupt events to TinyUSB IRQ Handler
|
|
//--------------------------------------------------------------------+
|
|
void USB0_FS_IRQHandler(void)
|
|
{
|
|
tud_int_handler(0);
|
|
}
|
|
|
|
void USB1_HS_IRQHandler(void)
|
|
{
|
|
tud_int_handler(1);
|
|
}
|
|
|
|
void board_init(void)
|
|
{
|
|
BOARD_InitPins();
|
|
BOARD_InitBootClocks();
|
|
CLOCK_SetupExtClocking(XTAL0_CLK_HZ);
|
|
|
|
// 1ms tick timer
|
|
SysTick_Config(SystemCoreClock / 1000);
|
|
|
|
#if CFG_TUSB_OS == OPT_OS_FREERTOS
|
|
// If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
|
|
NVIC_SetPriority(USB1_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY );
|
|
#endif
|
|
|
|
// LED
|
|
CLOCK_EnableClock(LED_CLK);
|
|
gpio_pin_config_t led_config = {
|
|
kGPIO_DigitalOutput,
|
|
0,
|
|
};
|
|
GPIO_PinInit(LED_GPIO,LED_PIN, &led_config);
|
|
board_led_write(0);
|
|
|
|
#ifdef NEOPIXEL_PIN
|
|
// Neopixel
|
|
static uint32_t pixelData[NEOPIXEL_NUMBER];
|
|
IOCON_PinMuxSet(IOCON, NEOPIXEL_PORT, NEOPIXEL_PIN, IOCON_PIO_DIG_FUNC4_EN);
|
|
|
|
sctpix_init(NEOPIXEL_TYPE);
|
|
sctpix_addCh(NEOPIXEL_CH, pixelData, NEOPIXEL_NUMBER);
|
|
sctpix_setPixel(NEOPIXEL_CH, 0, 0x100010);
|
|
sctpix_setPixel(NEOPIXEL_CH, 1, 0x100010);
|
|
sctpix_show();
|
|
#endif
|
|
|
|
// Button
|
|
#ifdef BUTTON_GPIO
|
|
CLOCK_EnableClock(BUTTON_CLK);
|
|
gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0};
|
|
GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config);
|
|
#endif
|
|
|
|
#ifdef UART_DEV
|
|
// UART
|
|
// IOCON_PinMuxSet(IOCON, UART_RX_PINMUX);
|
|
// IOCON_PinMuxSet(IOCON, UART_TX_PINMUX);
|
|
|
|
// Enable UART when debug log is on
|
|
board_uart_init_clock();
|
|
|
|
lpuart_config_t uart_config;
|
|
LPUART_GetDefaultConfig(&uart_config);
|
|
uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE;
|
|
uart_config.enableTx = true;
|
|
uart_config.enableRx = true;
|
|
LPUART_Init(UART_DEV, &uart_config, 12000000u);
|
|
#endif
|
|
|
|
// USB VBUS
|
|
/* PORT0 PIN22 configured as USB0_VBUS */
|
|
|
|
#if PORT_SUPPORT_DEVICE(0)
|
|
// Port0 is Full Speed
|
|
|
|
CLOCK_AttachClk(kCLK_48M_to_USB0);
|
|
CLOCK_EnableClock(kCLOCK_Usb0Ram);
|
|
CLOCK_EnableClock(kCLOCK_Usb0Fs);
|
|
CLOCK_EnableUsbfsClock();
|
|
#endif
|
|
|
|
#if PORT_SUPPORT_DEVICE(1)
|
|
// Port1 is High Speed
|
|
|
|
// Power
|
|
SPC0->ACTIVE_VDELAY = 0x0500;
|
|
/* Change the power DCDC to 1.8v (By default, DCDC is 1.8V), CORELDO to 1.1v (By default, CORELDO is 1.0V) */
|
|
SPC0->ACTIVE_CFG &= ~SPC_ACTIVE_CFG_CORELDO_VDD_DS_MASK;
|
|
SPC0->ACTIVE_CFG |= SPC_ACTIVE_CFG_DCDC_VDD_LVL(0x3) | SPC_ACTIVE_CFG_CORELDO_VDD_LVL(0x3) |
|
|
SPC_ACTIVE_CFG_SYSLDO_VDD_DS_MASK | SPC_ACTIVE_CFG_DCDC_VDD_DS(0x2u);
|
|
/* Wait until it is done */
|
|
while (SPC0->SC & SPC_SC_BUSY_MASK) {}
|
|
if (0u == (SCG0->LDOCSR & SCG_LDOCSR_LDOEN_MASK)) {
|
|
SCG0->TRIM_LOCK = 0x5a5a0001U;
|
|
SCG0->LDOCSR |= SCG_LDOCSR_LDOEN_MASK;
|
|
/* wait LDO ready */
|
|
while (0U == (SCG0->LDOCSR & SCG_LDOCSR_VOUT_OK_MASK));
|
|
}
|
|
SYSCON->AHBCLKCTRLSET[2] |= SYSCON_AHBCLKCTRL2_USB_HS_MASK | SYSCON_AHBCLKCTRL2_USB_HS_PHY_MASK;
|
|
SCG0->SOSCCFG &= ~(SCG_SOSCCFG_RANGE_MASK | SCG_SOSCCFG_EREFS_MASK);
|
|
/* xtal = 20 ~ 30MHz */
|
|
SCG0->SOSCCFG = (1U << SCG_SOSCCFG_RANGE_SHIFT) | (1U << SCG_SOSCCFG_EREFS_SHIFT);
|
|
SCG0->SOSCCSR |= SCG_SOSCCSR_SOSCEN_MASK;
|
|
while (1) {
|
|
if (SCG0->SOSCCSR & SCG_SOSCCSR_SOSCVLD_MASK) {
|
|
break;
|
|
}
|
|
}
|
|
|
|
// Clock
|
|
SYSCON->CLOCK_CTRL |= SYSCON_CLOCK_CTRL_CLKIN_ENA_MASK | SYSCON_CLOCK_CTRL_CLKIN_ENA_FM_USBH_LPT_MASK;
|
|
CLOCK_EnableClock(kCLOCK_UsbHs);
|
|
CLOCK_EnableClock(kCLOCK_UsbHsPhy);
|
|
CLOCK_EnableUsbhsPhyPllClock(kCLOCK_Usbphy480M, 24000000U);
|
|
CLOCK_EnableUsbhsClock();
|
|
|
|
// USB PHY
|
|
#if ((!(defined FSL_FEATURE_SOC_CCM_ANALOG_COUNT)) && (!(defined FSL_FEATURE_SOC_ANATOP_COUNT)))
|
|
USBPHY->TRIM_OVERRIDE_EN = 0x001fU; /* override IFR value */
|
|
#endif
|
|
|
|
// Enable PHY support for Low speed device + LS via FS Hub
|
|
USBPHY->CTRL |= USBPHY_CTRL_SET_ENUTMILEVEL2_MASK | USBPHY_CTRL_SET_ENUTMILEVEL3_MASK;
|
|
|
|
// Enable all power for normal operation
|
|
USBPHY->PWD = 0;
|
|
|
|
// TX Timing
|
|
uint32_t phytx = USBPHY->TX;
|
|
phytx &= ~(USBPHY_TX_D_CAL_MASK | USBPHY_TX_TXCAL45DM_MASK | USBPHY_TX_TXCAL45DP_MASK);
|
|
phytx |= USBPHY_TX_D_CAL(0x04) | USBPHY_TX_TXCAL45DP(0x07) | USBPHY_TX_TXCAL45DM(0x07);
|
|
//phytx |= USBPHY_TX_D_CAL(0x0C) | USBPHY_TX_TXCAL45DP(0x06) | USBPHY_TX_TXCAL45DM(0x06);
|
|
USBPHY->TX = phytx;
|
|
#endif
|
|
}
|
|
|
|
//--------------------------------------------------------------------+
|
|
// Board porting API
|
|
//--------------------------------------------------------------------+
|
|
|
|
void board_led_write(bool state)
|
|
{
|
|
GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
|
|
|
|
#ifdef NEOPIXEL_PIN
|
|
if (state) {
|
|
sctpix_setPixel(NEOPIXEL_CH, 0, 0x100000);
|
|
sctpix_setPixel(NEOPIXEL_CH, 1, 0x101010);
|
|
} else {
|
|
sctpix_setPixel(NEOPIXEL_CH, 0, 0x001000);
|
|
sctpix_setPixel(NEOPIXEL_CH, 1, 0x000010);
|
|
}
|
|
sctpix_show();
|
|
#endif
|
|
}
|
|
|
|
uint32_t board_button_read(void)
|
|
{
|
|
#ifdef BUTTON_GPIO
|
|
return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN);
|
|
#endif
|
|
}
|
|
|
|
int board_uart_read(uint8_t* buf, int len)
|
|
{
|
|
(void) buf; (void) len;
|
|
return 0;
|
|
}
|
|
|
|
int board_uart_write(void const * buf, int len)
|
|
{
|
|
#ifdef UART_DEV
|
|
LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len);
|
|
return len;
|
|
#else
|
|
(void) buf; (void) len;
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
#if CFG_TUSB_OS == OPT_OS_NONE
|
|
volatile uint32_t system_ticks = 0;
|
|
void SysTick_Handler(void)
|
|
{
|
|
system_ticks++;
|
|
}
|
|
|
|
uint32_t board_millis(void)
|
|
{
|
|
return system_ticks;
|
|
}
|
|
#endif
|