229 lines
7.2 KiB
C
229 lines
7.2 KiB
C
/**************************************************************************/
|
|
/*!
|
|
@file board_ea4357.c
|
|
@author hathach (tinyusb.org)
|
|
|
|
@section LICENSE
|
|
|
|
Software License Agreement (BSD License)
|
|
|
|
Copyright (c) 2013, hathach (tinyusb.org)
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
1. Redistributions of source code must retain the above copyright
|
|
notice, this list of conditions and the following disclaimer.
|
|
2. Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in the
|
|
documentation and/or other materials provided with the distribution.
|
|
3. Neither the name of the copyright holders nor the
|
|
names of its contributors may be used to endorse or promote products
|
|
derived from this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
|
|
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
|
|
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND
|
|
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
This file is part of the tinyusb stack.
|
|
*/
|
|
/**************************************************************************/
|
|
|
|
#ifdef BOARD_EA4357
|
|
|
|
#include "../board.h"
|
|
#include "pca9532.h"
|
|
|
|
#define BOARD_UART_PORT LPC_USART0
|
|
#define BOARD_UART_PIN_PORT 0x0f
|
|
#define BOARD_UART_PIN_TX 10 // PF.10 : UART0_TXD
|
|
#define BOARD_UART_PIN_RX 11 // PF.11 : UART0_RXD
|
|
|
|
static const struct {
|
|
uint8_t mux_port;
|
|
uint8_t mux_pin;
|
|
|
|
uint8_t gpio_port;
|
|
uint8_t gpio_pin;
|
|
}buttons[] =
|
|
{
|
|
{0x0a, 3, 4, 10 }, // Joystick up
|
|
{0x09, 1, 4, 13 }, // Joystick down
|
|
{0x0a, 2, 4, 9 }, // Joystick left
|
|
{0x09, 0, 4, 12 }, // Joystick right
|
|
{0x0a, 1, 4, 8 }, // Joystick press
|
|
{0x02, 7, 0, 7 }, // SW6
|
|
};
|
|
|
|
enum {
|
|
BOARD_BUTTON_COUNT = sizeof(buttons) / sizeof(buttons[0])
|
|
};
|
|
|
|
/*------------------------------------------------------------------*/
|
|
/* TUSB HAL MILLISECOND
|
|
*------------------------------------------------------------------*/
|
|
#if CFG_TUSB_OS == OPT_OS_NONE
|
|
|
|
volatile uint32_t system_ticks = 0;
|
|
|
|
void SysTick_Handler (void)
|
|
{
|
|
system_ticks++;
|
|
}
|
|
|
|
uint32_t tusb_hal_millis(void)
|
|
{
|
|
return board_tick2ms(system_ticks);
|
|
}
|
|
|
|
#endif
|
|
|
|
/*------------------------------------------------------------------*/
|
|
/* BOARD API
|
|
*------------------------------------------------------------------*/
|
|
|
|
/* System configuration variables used by chip driver */
|
|
const uint32_t ExtRateIn = 0;
|
|
const uint32_t OscRateIn = 12000000;
|
|
|
|
static const PINMUX_GRP_T pinmuxing[] =
|
|
{
|
|
// USB
|
|
|
|
/* I2S */
|
|
{0x3, 0, (SCU_PINIO_FAST | SCU_MODE_FUNC2)}, //I2S0_TX_CLK
|
|
{0xC, 12, (SCU_PINIO_FAST | SCU_MODE_FUNC6)}, //I2S0_TX_SDA
|
|
{0xC, 13, (SCU_PINIO_FAST | SCU_MODE_FUNC6)}, //I2S0_TX_WS
|
|
{0x6, 0, (SCU_PINIO_FAST | SCU_MODE_FUNC4)}, //I2S0_RX_SCK
|
|
{0x6, 1, (SCU_PINIO_FAST | SCU_MODE_FUNC3)}, //I2S0_RX_WS
|
|
{0x6, 2, (SCU_PINIO_FAST | SCU_MODE_FUNC3)}, //I2S0_RX_SDA
|
|
};
|
|
|
|
/* Pin clock mux values, re-used structure, value in first index is meaningless */
|
|
static const PINMUX_GRP_T pinclockmuxing[] =
|
|
{
|
|
{0, 0, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
|
|
{0, 1, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
|
|
{0, 2, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
|
|
{0, 3, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)},
|
|
};
|
|
|
|
// Invoked by startup code
|
|
void SystemInit(void)
|
|
{
|
|
/* Setup system level pin muxing */
|
|
Chip_SCU_SetPinMuxing(pinmuxing, sizeof(pinmuxing) / sizeof(PINMUX_GRP_T));
|
|
|
|
/* Clock pins only, group field not used */
|
|
for (int i = 0; i < (sizeof(pinclockmuxing) / sizeof(pinclockmuxing[0])); i++)
|
|
{
|
|
Chip_SCU_ClockPinMuxSet(pinclockmuxing[i].pinnum, pinclockmuxing[i].modefunc);
|
|
}
|
|
|
|
Chip_SetupXtalClocking();
|
|
}
|
|
|
|
void board_init(void)
|
|
{
|
|
SystemCoreClockUpdate();
|
|
|
|
#if CFG_TUSB_OS == OPT_OS_NONE
|
|
SysTick_Config( SystemCoreClock / BOARD_TICKS_HZ );
|
|
#endif
|
|
|
|
Chip_GPIO_Init(LPC_GPIO_PORT);
|
|
|
|
//------------- LED -------------//
|
|
/* Init I2C */
|
|
Chip_SCU_I2C0PinConfig(I2C0_STANDARD_FAST_MODE);
|
|
Chip_I2C_Init(I2C0);
|
|
Chip_I2C_SetClockRate(I2C0, 100000);
|
|
Chip_I2C_SetMasterEventHandler(I2C0, Chip_I2C_EventHandlerPolling);
|
|
|
|
pca9532_init();
|
|
|
|
#if 0
|
|
//------------- BUTTON -------------//
|
|
for(uint8_t i=0; i<BOARD_BUTTON_COUNT; i++)
|
|
{
|
|
scu_pinmux(buttons[i].mux_port, buttons[i].mux_pin, GPIO_NOPULL, FUNC0);
|
|
GPIO_SetDir(buttons[i].gpio_port, BIT_(buttons[i].gpio_pin), 0);
|
|
}
|
|
|
|
//------------- UART -------------//
|
|
scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_TX, MD_PDN, FUNC1);
|
|
scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_RX, MD_PLN | MD_EZI | MD_ZI, FUNC1);
|
|
|
|
UART_CFG_Type UARTConfigStruct;
|
|
UART_ConfigStructInit(&UARTConfigStruct);
|
|
UARTConfigStruct.Baud_rate = CFG_UART_BAUDRATE;
|
|
UARTConfigStruct.Clock_Speed = 0;
|
|
|
|
UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
|
|
UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
|
|
#endif
|
|
|
|
//------------- USB -------------//
|
|
// USB0 Vbus Power: P2_3 on EA4357 channel B U20 GPIO26 active low (base board)
|
|
Chip_SCU_PinMuxSet(2, 3, SCU_MODE_PULLUP | SCU_MODE_INBUFF_EN | SCU_MODE_FUNC7);
|
|
|
|
#if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE
|
|
// P9_5 (GPIO5[18]) (GPIO28 on oem base) as USB connect, active low.
|
|
Chip_SCU_PinMuxSet(9, 5, SCU_MODE_PULLDOWN | SCU_MODE_FUNC4);
|
|
Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, 5, 18);
|
|
#endif
|
|
|
|
// USB1 Power: EA4357 channel A U20 is enabled by SJ5 connected to pad 1-2, no more action required
|
|
// TODO Remove R170, R171, solder a pair of 15K to USB1 D+/D- to test with USB1 Host
|
|
}
|
|
|
|
// LED
|
|
void board_led_control(bool state)
|
|
{
|
|
if (state)
|
|
{
|
|
pca9532_setLeds( LED1, 0 );
|
|
}else
|
|
{
|
|
pca9532_setLeds( 0, LED1);
|
|
}
|
|
}
|
|
|
|
//--------------------------------------------------------------------+
|
|
// BUTTONS
|
|
//--------------------------------------------------------------------+
|
|
static bool button_read(uint8_t id)
|
|
{
|
|
// return !BIT_TEST_( GPIO_ReadValue(buttons[id].gpio_port), buttons[id].gpio_pin ); // button is active low
|
|
}
|
|
|
|
uint32_t board_buttons(void)
|
|
{
|
|
uint32_t result = 0;
|
|
|
|
// for(uint8_t i=0; i<BOARD_BUTTON_COUNT; i++) result |= (button_read(i) ? BIT_(i) : 0);
|
|
|
|
return result;
|
|
}
|
|
|
|
//--------------------------------------------------------------------+
|
|
// UART
|
|
//--------------------------------------------------------------------+
|
|
uint8_t board_uart_getchar(void)
|
|
{
|
|
//return UART_ReceiveByte(BOARD_UART_PORT);
|
|
}
|
|
void board_uart_putchar(uint8_t c)
|
|
{
|
|
//UART_Send(BOARD_UART_PORT, &c, 1, BLOCKING);
|
|
}
|
|
|
|
#endif
|