55 lines
1.6 KiB
Makefile
55 lines
1.6 KiB
Makefile
ST_FAMILY = l0
|
|
DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
|
|
|
|
ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
|
|
ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
|
|
|
|
CFLAGS += \
|
|
-flto \
|
|
-mthumb \
|
|
-mabi=aapcs \
|
|
-mcpu=cortex-m0plus \
|
|
-mfloat-abi=soft \
|
|
-nostdlib -nostartfiles \
|
|
-DSTM32L053xx \
|
|
-DCFG_EXAMPLE_MSC_READONLY \
|
|
-DCFG_EXAMPLE_VIDEO_READONLY \
|
|
-DCFG_TUSB_MCU=OPT_MCU_STM32L0
|
|
|
|
# mcu driver cause following warnings
|
|
CFLAGS += -Wno-error=unused-parameter -Wno-error=maybe-uninitialized -Wno-error=redundant-decls
|
|
|
|
# All source paths should be relative to the top level.
|
|
LD_FILE = hw/bsp/$(BOARD)/STM32L053C8Tx_FLASH.ld
|
|
|
|
SRC_C += \
|
|
src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \
|
|
$(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
|
|
$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c
|
|
|
|
SRC_S += \
|
|
$(ST_CMSIS)/Source/Templates/gcc/startup_stm32l053xx.s
|
|
|
|
INC += \
|
|
$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
|
|
$(TOP)/$(ST_CMSIS)/Include \
|
|
$(TOP)/$(ST_HAL_DRIVER)/Inc \
|
|
$(TOP)/hw/bsp/$(BOARD)
|
|
|
|
# For freeRTOS port source
|
|
FREERTOS_PORT = ARM_CM0
|
|
|
|
# For flash-jlink target
|
|
JLINK_DEVICE = STM32L053R8
|
|
|
|
# Path to STM32 Cube Programmer CLI, should be added into system path
|
|
STM32Prog = STM32_Programmer_CLI
|
|
|
|
# flash target using on-board stlink
|
|
flash: $(BUILD)/$(PROJECT).elf
|
|
$(STM32Prog) --connect port=swd --write $< --go
|